TN-ETHSOAM-MIB
166 objects
TBD
Imported Objects
| IEEE8021-CFM-MIB | dot1agCfmLtrEntry dot1agCfmMepEntry dot1agCfmMepIdentifier |
| IEEE8021-TC-MIB | IEEE8021PriorityValue |
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| Q-BRIDGE-MIB | VlanId VlanIdOrNone |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| TRANSITION-SMI | 1ag tnProducts |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.5.105 | IdentitytnEthSoamMIB | TBD | ||
| 1.3.6.1.4.1.868.2.5.105.0 | NodetnEthSoamMIBNotifications | |||
| 1.3.6.1.4.1.868.2.5.105.0.1 | NotificationtnEthSoamFaultAlarm | current | An EthSoam has a persistent defect condition. A notification (fault alarm) is sent to the management entity with the OID of the EthSoam that has detected the f… | |
| 1.3.6.1.4.1.868.2.5.105.0.2 | NotificationtnEthSoamPeerFaultAlarm | current | An EthSoamPeer has a persistent defect condition. A notification (fault alarm) is sent to the management entity with the OID of the EthSoamPeer that has detect… | |
| 1.3.6.1.4.1.868.2.5.105.1 | NodetnEthSoamMIBObjects | |||
| 1.3.6.1.4.1.868.2.5.105.1.1 | NodetnEthSoamMPMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.1.1 | TabletnEthSoamMPTable | not-accessible | current | This table provides configuration of SOAM Maintenance Point. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1 | RowtnEthSoamMPEntry | not-accessible | current | A entry in the table represents a configuration for local SOAM. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.1 | ColumntnEthSoaminstance | not-accessible | current | This is the configuration of the two possible Maintenance Association Identifier formats. ITU ICC: This is defined by ITU. 'ICC' can be max. 6 char. 'MEG id' c… |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.2 | ColumntnEthSoamDomaintype | read-create | current | The Domain Mode affects the OAM. The allowed values are Port: This is a MEP in the Port Domain. 'Flow Instance' is a Port. Esp: Future use. Evc: This is a MEP … |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.3 | ColumntnEthSoamMode | read-create | current | MEP: This is a Maintenance Entity End Point. MIP: This is a Maintenance Entity Intermediate Point. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.4 | ColumntnEthSoamdirection | read-create | current | Direction in which the MP faces on the Bridge Port. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.5 | ColumntnEthSoamresidencePort | read-create | current | This object is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, to which the MEP is attached. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.6 | ColumntnEthSoamlevel | read-create | current | Level of the Maintenance Point. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.7 | ColumntnEthSoamFlowInstance | read-create | current | The MEP is related to this flow - See 'Domain'. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.8 | ColumntnEthSoamTaggedVID | read-create | current | Port MEP: An outer C/S-tag (depending on VLAN Port Type) is added with this VID. Entering '0' means no TAG added. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.9 | ColumntnEthSoamAlarm | read-only | current | An active alarm on the MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.1.1.1.11 | ColumntnEthSoamStatus | read-create | current | The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated. |
| 1.3.6.1.4.1.868.2.5.105.1.2 | NodetnEthSoamPeerCfgMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.2.1 | TabletnEthSoamPeerCfgTable | not-accessible | current | This table has entries which generate a configuration for peer SOAM. |
| 1.3.6.1.4.1.868.2.5.105.1.2.1.1 | RowtnEthSoamPeerCfgEntry | not-accessible | current | A entry in the table represents a configuration for peer SOAM. |
| 1.3.6.1.4.1.868.2.5.105.1.2.1.1.1 | ColumntnEthSoamPeerCfgMepId | not-accessible | current | The ID of the MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.2.1.1.2 | ColumntnEthSoamPeerCfgUnicastMac | read-write | current | This MAC will be used when unicast is selected with this peer MEP. Also this MAC is used to create HW checking of receiving CCM PDU (LOC detection) from this M… |
| 1.3.6.1.4.1.868.2.5.105.1.2.1.1.3 | ColumntnEthSoamPeerCfgRowState | read-create | current | row status. |
| 1.3.6.1.4.1.868.2.5.105.1.3 | NodetnEthSoamPeerStatusMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.3.1 | TabletnEthSoamPeerStatusTable | not-accessible | current | This table provides configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.3.1.1 | RowtnEthSoamPeerStatusEntry | not-accessible | current | This entry represents configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.3.1.1.1 | ColumntnEthSoamPeerStatusMepId | not-accessible | current | MEPID. |
| 1.3.6.1.4.1.868.2.5.105.1.3.1.1.2 | ColumntnEthSoamPeerStatuscLOC | read-only | current | Fault Cause indicating that no CCM has been received (in 3,5 periods) - from this peer MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.3.1.1.3 | ColumntnEthSoamPeerStatuscRDI | read-only | current | Fault Cause indicating that a CCM is received with Remote Defect Indication - from this peer MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.3.1.1.4 | ColumntnEthSoamPeerStatuscPeriod | read-only | current | Fault Cause indicating that a CCM is received with a period different what is configured for this MEP - from this peer MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.3.1.1.5 | ColumntnEthSoamPeerStatuscPriority | read-only | current | Fault Cause indicating that a CCM is received with a priority different what is configured for this MEP - from this peer MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.4 | NodetnEthSoamAPSCfgMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.4.1 | TabletnEthSoamAPSCfgTable | not-accessible | current | This table provides configuration about the APSCfg that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.4.1.1 | RowtnEthSoamAPSCfgEntry | not-accessible | current | This entry represents configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.4.1.1.1 | ColumntnEthSoamAPSCfgEnable | read-create | current | Automatic Protection Switching protocol information transportation based on transmitting/receiving R-APS/L-APS PDU can be enabled/disabled. Must be enabled to … |
| 1.3.6.1.4.1.868.2.5.105.1.4.1.1.2 | ColumntnEthSoamAPSCfgPriority | read-create | current | The priority to be inserted as PCP bits in TAG (if any). |
| 1.3.6.1.4.1.868.2.5.105.1.4.1.1.3 | ColumntnEthSoamAPSCfgCast | read-create | current | Selection of APS PDU transmitted unicast or multi-cast. The unicast MAC will be taken from the 'Unicast Peer MAC' configuration. Unicast is only valid for L-AP… |
| 1.3.6.1.4.1.868.2.5.105.1.4.1.1.4 | ColumntnEthSoamAPSCfgType | read-create | current | R-APS: APS PDU is transmitted as R-APS - this is for ERPS. L-APS: APS PDU is transmitted as L-APS - this is for ELPS. |
| 1.3.6.1.4.1.868.2.5.105.1.4.1.1.5 | ColumntnEthSoamAPSCfgLastOctet | read-create | current | This is the last octet of the transmitted and expected RAPS multi-cast MAC. In G.8031 (03/2010) a RAPS multi-cast MAC is defined as 01-19-A7-00-00-XX. In curre… |
| 1.3.6.1.4.1.868.2.5.105.1.5 | NodetnEthSoamClientCfgMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.5.1 | TabletnEthSoamClientCfgTable | not-accessible | current | This table provides configuration about the Link Trace reply that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1 | RowtnEthSoamClientCfgEntry | not-accessible | current | This entry represents configuration about the Client Configuration that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.1 | ColumntnEthSoamClientCfgDomain | read-create | current | The domain of the client layer. Must be EVC. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.2 | ColumntnEthSoamClientCfgLevel | read-write | current | Client layer level - meaning that PDU transmitted in client layer flows will be on this level. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.3 | ColumntnEthSoamClientCfgFlow1 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.4 | ColumntnEthSoamClientCfgFlow2 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.5 | ColumntnEthSoamClientCfgFlow3 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.6 | ColumntnEthSoamClientCfgFlow4 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.7 | ColumntnEthSoamClientCfgFlow5 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.8 | ColumntnEthSoamClientCfgFlow6 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.9 | ColumntnEthSoamClientCfgFlow7 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.10 | ColumntnEthSoamClientCfgFlow8 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.11 | ColumntnEthSoamClientCfgFlow9 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.5.1.1.12 | ColumntnEthSoamClientCfgFlow10 | read-create | current | Client layer flow instance numbers. |
| 1.3.6.1.4.1.868.2.5.105.1.6 | NodetnEthSoamLocalCfgMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.6.1 | TabletnEthSoamLocalCfgTable | not-accessible | current | This table has entries which generate a configuration for local SOAM. |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1 | RowtnEthSoamLocalCfgEntry | not-accessible | current | A entry in the table represents a configuration for local SOAM. |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.1 | ColumntnEthSoamFormat | read-write | current | This is the configuration of the two possible Maintenance Association Identifier formats. ITU ICC: This is defined by ITU. 'ICC' can be max. 6 char. 'MEG id' c… |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.2 | ColumntnEthSoamDomainName | read-write | current | This is either ITU ICC (MEG ID value[1-6]) or IEEE Maintenance Domain Name - depending on 'Format'. See 'Format'. |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.3 | ColumntnEthSoamMegOrMaName | read-write | current | This is either ITU UMC (MEG ID value[7-13]) or IEEE Short MA Name - depending on 'Format'. See 'Format'. In case of ITU ICC format this can be max. 7 char. If … |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.4 | ColumntnEthSoamMepID | read-write | current | This value will become the transmitted two byte CCM MEP ID. |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.5 | ColumntnEthSoamCcmInterval | read-write | current | Interval between CCM transmissions to be used by all MEPs in the MA. |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.6 | ColumntnEthSoamEVCQos | read-write | current | This is only relevant for a EVC MEP. This is the Qos of the EVC used for getting QoS counters for Loss Measurement. |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.7 | ColumntnEthSoamEVCPolicyID | read-write | current | This is relevant for an EVC Egress/Up-MEP. This is the Policy number of the relevant ECE. The Policy ID that the generated TST frames will get as IS1 action. C… |
| 1.3.6.1.4.1.868.2.5.105.1.6.1.1.8 | ColumntnEthSoamVOE | read-write | current | This will attempt to utilize VOE HW for MEP implementation. Not all platforms support VOE. |
| 1.3.6.1.4.1.868.2.5.105.1.7 | NodetnEthSoamStatusMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.7.1 | TabletnEthSoamStatusTable | not-accessible | current | This table provides configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1 | RowtnEthSoamStatusEntry | not-accessible | current | This entry represents configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.1 | ColumntnEthSoamStatusCCMLevel | read-only | current | Fault Cause indicating that a CCM is received with a lower level than the configured for this MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.2 | ColumntnEthSoamStatusCCMMeg | read-only | current | Fault Cause indicating that a CCM is received with a MEG ID different from configured for this MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.3 | ColumntnEthSoamStatusCCMMep | read-only | current | Fault Cause indicating that a CCM is received with a MEP ID different from all 'Peer MEP ID' configured for this MEP. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.4 | ColumntnEthSoamStatusAIS | read-only | current | Fault Cause indicating that AIS PDU is received. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.5 | ColumntnEthSoamStatusCLK | read-only | current | Fault Cause indicating that LCK PDU is received. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.6 | ColumntnEthSoamStatusSSF | read-only | current | Fault Cause indicating that server layer is indicating Signal Fail. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.7 | ColumntnEthSoamStatusBLK | read-only | current | The consequent action of blocking service frames in this flow is active. |
| 1.3.6.1.4.1.868.2.5.105.1.7.1.1.8 | ColumntnEthSoamStatusTSF | read-only | current | The consequent action of indicating Trail Signal Fail to-wards protection is active. |
| 1.3.6.1.4.1.868.2.5.105.1.8 | NodetnEthSoamLossStateMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.8.1 | TabletnEthSoamLossStateTable | not-accessible | current | This table has entries which generate a configuration for loss measurement State. |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1 | RowtnEthSoamLossStateEntry | not-accessible | current | A entry in the table represents a configuration for loss measurement State. |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1.1 | ColumntnEthSoamLossStateTxCount | read-only | current | The accumulated Tx frame loss count. |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1.2 | ColumntnEthSoamLossStateRxCount | read-only | current | The accumulated Rx frame loss count. |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1.3 | ColumntnEthSoamLossStateNELossCount | read-only | current | The accumulated near end frame loss count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1.4 | ColumntnEthSoamLossStateFELossCount | read-only | current | The accumulated far end frame loss count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1.5 | ColumntnEthSoamLossStateNELossRatio | read-only | current | The near end frame loss ratio calculated based on the near end frame loss count and far end frame transmitted - in the latest 'FLR Interval'. The result is giv… |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1.6 | ColumntnEthSoamLossStateFELossRatio | read-only | current | The far end frame loss ratio calculated based on the far end frame loss count and near end frame transmitted - in the latest 'FLR Interval'. The result is give… |
| 1.3.6.1.4.1.868.2.5.105.1.8.1.1.7 | ColumntnEthSoamLossStateAction | read-write | current | Set of this check and save will clear the accumulated counters and restart ratio calculation. |
| 1.3.6.1.4.1.868.2.5.105.1.9 | NodetnEthSoamTSExtMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.9.1 | TabletnEthSoamTSExtTable | not-accessible | current | This table has entries which generate a configuration for test signal. |
| 1.3.6.1.4.1.868.2.5.105.1.9.1.1 | RowtnEthSoamTSExtEntry | not-accessible | current | A entry in the table represents a configuration for test signal. |
| 1.3.6.1.4.1.868.2.5.105.1.9.1.1.1 | ColumntnEthSoamTSSeqNum | read-write | current | sequence number. |
| 1.3.6.1.4.1.868.2.5.105.1.9.1.1.2 | ColumntnEthSoamTSStateRxRate | read-only | current | The current received TST frame bit rate in 100 Kbps. This is calculated on a 1 s. basis, starting when first TST frame is received after 'Clear'. The frame siz… |
| 1.3.6.1.4.1.868.2.5.105.1.9.1.1.3 | ColumntnEthSoamTSStateAction | read-write | current | This will clear all Test Signal State. Transmission of TST frame will be restarted. Calculation of 'Rx frame count', 'RX rate' and 'Test time' will be started … |
| 1.3.6.1.4.1.868.2.5.105.1.9.1.1.4 | ColumntnEthSoamTestCfgPattern | read-create | current | This attribute specifies the type of test pattern to be sent or received in an OAM PDU Test TLV. |
| 1.3.6.1.4.1.868.2.5.105.1.10 | NodetnEthSoamLtmMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.10.1 | TabletnEthSoamLtmTable | not-accessible | current | This table provides configuration about ltm priority that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.10.1.1 | RowtnEthSoamLtmEntry | not-accessible | current | This entry represents configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.10.1.1.1 | ColumntnEthSoamltmPriority | read-create | current | The priority to be inserted as PCP bits in TAG (if any). |
| 1.3.6.1.4.1.868.2.5.105.1.11 | NodetnEthSoamLtrMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.11.1 | TabletnEthSoamLtrTable | not-accessible | current | This table provides configuration about ltm priority that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.11.1.1 | RowtnEthSoamLtrEntry | not-accessible | current | This entry represents configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.11.1.1.1 | ColumntnEthSoamLtrDirection | read-only | current | The priority to be inserted as PCP bits in TAG (if any). |
| 1.3.6.1.4.1.868.2.5.105.1.12 | NodetnEthSoamAisCfgMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.12.1 | TabletnEthSoamAisCfgTable | not-accessible | current | This table provides configuration about ais that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.12.1.1 | RowtnEthSoamAisCfgEntry | not-accessible | current | This entry represents configuration about the SOAM that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.12.1.1.1 | ColumntnEthSoamAisCfgProtection | read-write | current | Selecting this means that the first 3 AIS PDU is transmitted as fast as possible - in case of using this for protection in the end point. |
| 1.3.6.1.4.1.868.2.5.105.1.13 | NodetnEthSoamDmCfgMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.13.1 | TabletnEthSoamDmCfgTable | not-accessible | current | This table provides configuration about the Delay Measurement that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1 | RowtnEthSoamDmCfgEntry | not-accessible | current | This entry represents configuration about the Delay Measurement that provide OAM services. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.1 | ColumntnEthSoamDmCfgEnable | read-create | current | Delay Measurement based on transmitting 1DM/DMM PDU can be enabled/disabled. Delay Measurement based on receiving and handling 1DM/DMR PDU is always enabled. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.2 | ColumntnEthSoamDmCfgPriority | read-create | current | The priority to be inserted as PCP bits in TAG (if any). |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.3 | ColumntnEthSoamDmCfgCast | read-create | current | Selection of 1DM/DMM PDU transmitted unicast or multicast. The unicast MAC will be configured through 'Peer MEP'. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.4 | ColumntnEthSoamDmCfgPeerId | read-create | current | Peer MEP ID. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.5 | ColumntnEthSoamDmCfgWayType | read-create | current | One-Way: One-Way Delay Measurement implemented on 1DM. Two-Way: Two-Way Delay Measurement implemented on DMM/DMR. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.6 | ColumntnEthSoamDmCfgTxMode | read-create | current | Standardize: Y.1731 standardize way to transmit 1DM/DMR. Proprietary: Vitesse proprietary way with follow-up packets to transmit 1DM/DMR. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.7 | ColumntnEthSoamDmCfgCalc | read-create | current | This is only used if the 'Way' is configured to Two-way. Round trip: The frame dealy calculated by the transmitting and receiving timestamps of initiators. Fra… |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.8 | ColumntnEthSoamDmCfgGap | read-create | current | The gap between transmitting 1DM/DMM PDU in 10ms. The range is 10 to 65535. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.9 | ColumntnEthSoamDmCfgCount | read-create | current | The number of last records to calculate. The range is 10 to 2000. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.10 | ColumntnEthSoamDmCfgUnit | read-create | current | The time resolution. |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.11 | ColumntnEthSoamDmCfgD2forD1 | read-create | current | Enable to use DMM/DMR packet to calculate one-way DM. If the option is enabled, the following action will be taken. When DMR is received, two-way delay (roundt… |
| 1.3.6.1.4.1.868.2.5.105.1.13.1.1.12 | ColumntnEthSoamDmCfgCOAction | read-create | current | The action to counter when overflow happens. |
| 1.3.6.1.4.1.868.2.5.105.1.14 | NodetnEthSoamDmStateMgmt | |||
| 1.3.6.1.4.1.868.2.5.105.1.14.1 | TabletnEthSoamDmStateTable | not-accessible | current | This table has entries which generate a configuration for delay measurement state. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1 | RowtnEthSoamDmStateEntry | not-accessible | current | A entry in the table which generate a configuration for delay measurement state. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.1 | ColumntnEthSoamDmStateFNTxCount | read-only | current | The accumulated transmit count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.2 | ColumntnEthSoamDmStateFNRxTimeout | read-only | current | The accumulated receive timeout count for two-way only - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.3 | ColumntnEthSoamDmStateFNRxCount | read-only | current | The accumulated receive count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.4 | ColumntnEthSoamDmStateFNRxError | read-only | current | The accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout). |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.5 | ColumntnEthSoamDmStateFNAvgTotal | read-only | current | The average delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.6 | ColumntnEthSoamDmStateFNAvgLastN | read-only | current | The average delay of the last n packets - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.7 | ColumntnEthSoamDmStateFNAvgVarTotal | read-only | current | The average delay variation - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.8 | ColumntnEthSoamDmStateFNAvgVarLastN | read-only | current | The average delay variation of the last n packets - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.9 | ColumntnEthSoamDmStateFNMinValue | read-only | current | The minimum delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.10 | ColumntnEthSoamDmStateFNMaxValue | read-only | current | The maximum delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.11 | ColumntnEthSoamDmStateFNOverFlow | read-only | current | The number of counter overflow - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.12 | ColumntnEthSoamDmStateNFTxCount | read-only | current | The accumulated transmit count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.13 | ColumntnEthSoamDmStateNFRxTimeout | read-only | current | The accumulated receive timeout count for two-way only - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.14 | ColumntnEthSoamDmStateNFRxCount | read-only | current | The accumulated receive count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.15 | ColumntnEthSoamDmStateNFRxError | read-only | current | The accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout). |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.16 | ColumntnEthSoamDmStateNFAvgTotal | read-only | current | The average delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.17 | ColumntnEthSoamDmStateNFAvgLastN | read-only | current | The average delay of the last n packets - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.18 | ColumntnEthSoamDmStateNFAvgVarTotal | read-only | current | The average delay variation - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.19 | ColumntnEthSoamDmStateNFAvgVarLastN | read-only | current | The average delay variation of the last n packets - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.20 | ColumntnEthSoamDmStateNFMinValue | read-only | current | The minimum delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.21 | ColumntnEthSoamDmStateNFMaxValue | read-only | current | The maximum delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.22 | ColumntnEthSoamDmStateNFOverFlow | read-only | current | The number of counter overflow - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.23 | ColumntnEthSoamDmStateTwoWayTxCount | read-only | current | The accumulated transmit count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.24 | ColumntnEthSoamDmStateTwoWayRxTimeout | read-only | current | The accumulated receive timeout count for two-way only - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.25 | ColumntnEthSoamDmStateTwoWayRxCount | read-only | current | The accumulated receive count - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.26 | ColumntnEthSoamDmStateTwoWayRxError | read-only | current | The accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout). |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.27 | ColumntnEthSoamDmStateTwoWayAvgTotal | read-only | current | The average delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.28 | ColumntnEthSoamDmStateTwoWayAvgLastN | read-only | current | The average delay of the last n packets - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.29 | ColumntnEthSoamDmStateTwoWayAvgVarTotal | read-only | current | The average delay variation - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.30 | ColumntnEthSoamDmStateTwoWayAvgVarLastN | read-only | current | The average delay variation of the last n packets - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.31 | ColumntnEthSoamDmStateTwoWayMinValue | read-only | current | The minimum delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.32 | ColumntnEthSoamDmStateTwoWayMaxValue | read-only | current | The maximum delay - since last 'clear'. The unit is microsecond. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.33 | ColumntnEthSoamDmStateTwoWayOverFlow | read-only | current | The number of counter overflow - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.1.14.1.1.34 | ColumntnEthSoamDmStateAction | read-write | current | The number of counter overflow - since last 'clear'. |
| 1.3.6.1.4.1.868.2.5.105.2 | NodetnEthSoamMIBConformance |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Dot1agCfmMaintAssocName | OCTET STRING (SIZE(1..45)) | current | Denotes a generic Maintenance Association Name. It is the part of the Maintenance Association Identifier which is unique within the Maintenance Domain Name and is appended to the Maintenance Domain Name to form the Main… |
| Dot1agCfmMaintDomainName | OCTET STRING (SIZE(1..43)) | current | Denotes a generic Maintenance Domain Name. A Dot1agCfmMaintDomainName value is always interpreted within the context of a Dot1agCfmMaintDomainNameType value. Every usage of the Dot1agCfmMaintDomainName textual conventio… |
| Dot1agCfmMDLevel | Integer32 (0..7) | current | Integer identifying the Maintenance Domain Level (MD Level). Higher numbers correspond to higher Maintenance Domains, those with the greatest physical reach, with the highest values for customers' CFM PDUs. Lower number… |
| Dot1agCfmMepId | Unsigned32 (1..8191) | current | Maintenance association End Point Identifier (MEPID): A small integer, unique over a given Maintenance Association, identifying a specific MEP. |
| Dot1agCfmMpDirection | INTEGER { down (1), up (2) } | current | Indicates the direction in which the Maintenance association (MEP or MIP) faces on the bridge port: down(1) Sends Continuity Check Messages away from the MAC Relay Entity. up(2) Sends Continuity Check Messages towards t… |
| TnEthSoamTestPatternType | INTEGER { allzero (1), allone (2), onezero (3) } | current | This enumeration data type indicates the type of test pattern to be sent in an OAM PDU Test TLV. The valid enumerated values associated with this type are: All Zreo(1) pattern will be '00000000' All One(2) pattern will … |
| TnEthSoamType | INTEGER { port (1), esp (2), evc (3), vlan (4), mplslink (5), mplstunnel (6), mplspw (7), mplslsp (8) } | current | Indicates the type of the domain in which the Maintenance association. |