TN-MGMT-TDM-MIB
36 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.5.3.0.6 | NotificationtnIfTDMAlarmIndicationSignalEvt | current | A alarm indication signal event is sent when there is a warning or alarm on TDM port. | |
| 1.3.6.1.4.1.868.2.5.3.1.2.6 | TabletnIfTDMTable | not-accessible | current | This table has entries for the TDM attributes. |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1 | RowtnIfTDMEntry | not-accessible | current | A entry in the table represents TDM attributes. |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.1 | ColumntnIfTDMAISTransmit | read-write | current | Transmit AIS(All Ones/BLUE) on Fiber(Copper) as an error signal when Copper interface(Fiber Interface) is down. When this error signal is transmitted, the AIS … |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.2 | ColumntnIfTDMAISFormat | read-write | current | Transmit AIS(All Ones:1111... sequence/BLUE:0101... sequence) on Fiber(Copper) as an error signal for DS3/E3/STS-1 port |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.3 | ColumntnIfTDMAlarmIndicationSignal | read-only | current | When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition. when equal to normal, this means no al… |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.4 | ColumntnIfTDMLongHaul | read-only | current | This variable indicates the current position of the remote device's Short/Long haul configuration switch. |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.5 | ColumntnIfTDMType | read-only | current | This variable indicates the type of the current device. T1=1.544MHz; E1=2.048MHz;E3 = 34.4Mb/s; DS3 = 44.7Mb/s; STS-1 = 51.8Mb/s |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.6 | ColumntnIfTDMT1E1LineBuildout | read-only | current | The characteristics T1E1 card's copper interface. |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.7 | ColumntnIfTDMDS3E3LineBuildout | read-write | current | The characteristics of DS3E3 card's copper interface. |
| 1.3.6.1.4.1.868.2.5.3.1.2.6.1.8 | ColumntnIfTDMConnectorType | read-only | current | The style of connector built into this device. |
| 1.3.6.1.4.1.868.2.5.3.1.2.9 | TabletnIfTDMExtTable | not-accessible | current | This table has entries for the Extral TDM attributes. |
| 1.3.6.1.4.1.868.2.5.3.1.2.9.1 | RowtnIfTDMExtEntry | not-accessible | current | A entry in the table represents Extral TDM attributes. |
| 1.3.6.1.4.1.868.2.5.3.1.2.9.1.1 | ColumntnIfTDMExtId | not-accessible | current | An index that uniquely identifies an entry in the tnIfTDMExtTable. This index permits the same interface to have several different channels |
| 1.3.6.1.4.1.868.2.5.3.1.2.9.1.2 | ColumntnIfTDMExtAISTrasmit | read-write | current | Transmit AIS(All Ones/BLUE) on the Channel as an error signal when Copper interface(Fiber Interface) is down. When this error signal is transmitted, the AIS of… |
| 1.3.6.1.4.1.868.2.5.3.1.2.9.1.3 | ColumntnIfTDMExtAISFormat | read-write | current | Transmit AIS(All Ones:1111... sequence/BLUE:0101... sequence) on the Channel as an error signal for the pair port |
| 1.3.6.1.4.1.868.2.5.3.1.2.9.1.4 | ColumntnIfTDMExtAlarmIndicationSingnal | read-only | current | When equal to alarm(1), this means that the other end of Channel has AIS enabled and is currently transmitting an alarm condition. when equal to normal(2), thi… |
| 1.3.6.1.4.1.868.2.5.3.1.2.9.1.5 | ColumntnIfTDMExtLoopback | read-write | current | This variable indicates the loopback state of the current Channel |
| 1.3.6.1.4.1.868.2.5.3.1.2.9.1.6 | ColumntnIfTDMExtYellowTrasmit | read-write | current | Transmit Yellow on the Channel as an error signal when Local Copper Interface is down. When this error signal is transmitted. |
| 1.3.6.1.4.1.868.2.5.3.1.2.10 | TabletnIfTDM2Table | not-accessible | current | This table has entries for the TDM 2 attributes. |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1 | RowtnIfTDM2Entry | not-accessible | current | A entry in the table represents the TDM 2 attributes. |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.1 | ColumntnIfTDM2FiberLineNum | read-only | current | This variable is indicate the links number of the Fiber Port, maybe single line or dual line |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.2 | ColumntnIfTDM2FiberActiveLine | read-write | current | This variable is indicate the active fiber link, if a multi-fiber line is used for hardware redundancy |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.3 | ColumntnIfTDM2FiberRevertive | read-write | current | This variable is used to decide whether to revertive the fiber link to primary link if applicable |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.4 | ColumntnIfTDM2FiberPrimaryLinkStatus | read-only | current | This variable indicates the fiber port primary line link status |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.5 | ColumntnIfTDM2FiberSecondaryLinkStatus | read-only | current | This variable indicates the fiber port secondary line link status |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.6 | ColumntnIfTDM2InBandLPEnable | read-write | current | This variable indicates whether In-band Loopback detect is enabled |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.7 | ColumntnIfTDM2InBandLPStartPatten | read-write | current | This binary string is used to set the In-band Loopback start Patten, such as 11000 string |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.8 | ColumntnIfTDM2InBandLPStopPatten | read-write | current | This binary string is used to set the In-band Loopback stop Patten, such as 11100 string |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.9 | ColumntnIfTDM2InBandPEERLPEnable | read-write | current | This variable indicates whether the PEER interface In-band Loopback detect is enabled |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.10 | ColumntnIfTDM2InBandPEERLPStartPatten | read-write | current | This binary string is used to set the PEER interface In-band Loopback start Patten, such as 11000 string |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.11 | ColumntnIfTDM2InBandPEERLPStopPatten | read-write | current | This binary string is used to set the PEER interface In-band Loopback stop Patten, such as 11100 string |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.12 | ColumntnIfTDM2InBandLPTimeoutEnable | read-write | current | This variable indicates whether the In-band Loopback timeout watchdog is enabled |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.13 | ColumntnIfTDM2InBandLPTimeoutCount | read-write | current | This variable is used to set the In-band Loopback timeout watchdog value, the unit is minute |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.14 | ColumntnIfTDM2InBandPEERLPTimeoutEnable | read-write | current | This variable indicates whether the Peer In-band Loopback timeout watchdog is enabled |
| 1.3.6.1.4.1.868.2.5.3.1.2.10.1.15 | ColumntnIfTDM2InBandPEERLPTimeoutCount | read-write | current | This variable is used to set the Peer In-band Loopback timeout watchdog value, the unit is minute |