ZHONE-COM-BRIDGE-REC-MIB
270 objects
BRIDGE record MIB IP Software Minneapolis, MN
Imported Objects
| ATM-TC-MIB | AtmVcIdentifier AtmVpIdentifier |
| IF-MIB | ifAlias ifIndex InterfaceIndex |
| RFC1213-MIB | ifPhysAddress PhysAddress |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter64 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | MacAddress TEXTUAL-CONVENTION TruthValue |
| Zhone | zhone zhoneBridge zhoneModules |
| Zhone-TC | ZhoneAdminString ZhoneRowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5504.4.7.1 | GroupbridgeInterfaceGroup | current | The bridge Interface Record object group. | |
| 1.3.6.1.4.1.5504.4.7.2 | TablebridgeInterfaceTable | not-accessible | current | This table contains information required for the management of bridge interfaces. |
| 1.3.6.1.4.1.5504.4.7.2.1 | RowbridgeInterfaceEntry | not-accessible | current | An entry exists for each bridge interface in the system. At a mininum the ifIndex must be present to create a row. |
| 1.3.6.1.4.1.5504.4.7.2.1.1 | ColumnbridgeIfVpi | read-create | current | If this bridge interface is on an ATM VC, the ATM VPI is specified here. If the bridge interface is not an ATM VC, this field is ignored. The VPI value for a V… |
| 1.3.6.1.4.1.5504.4.7.2.1.2 | ColumnbridgeIfVci | read-create | current | If this bridge interface is on an ATM VC, the ATM VCI is specified here. The range is 32...65535. The maximum VCI value cannot exceed the value allowable by at… |
| 1.3.6.1.4.1.5504.4.7.2.1.3 | ColumnbridgeIfVlanId | read-create | current | The Virtual LAN Id for VLAN Tag Insertion. |
| 1.3.6.1.4.1.5504.4.7.2.1.4 | ColumnbridgeIfStripAndInsert | read-create | current | If true, enable VLAN Tagging. |
| 1.3.6.1.4.1.5504.4.7.2.1.5 | ColumnbridgeIfCustomARP | read-create | current | If true, send ARP requests selectively or by flood. |
| 1.3.6.1.4.1.5504.4.7.2.1.6 | ColumnbridgeIfFilterBroadcast | read-create | current | If true, discard non-ARP broadcast packets. |
| 1.3.6.1.4.1.5504.4.7.2.1.7 | ColumnbridgeIfLearnIp | read-create | current | If true, snoop unicast packets to build ARP table. |
| 1.3.6.1.4.1.5504.4.7.2.1.8 | ColumnbridgeIfLearnUnicast | read-create | current | If true, snoop unicast packets to build MAC paths. |
| 1.3.6.1.4.1.5504.4.7.2.1.9 | ColumnbridgeIfMaxUnicast | read-create | current | Maximum number of unicast addresses for I/F. |
| 1.3.6.1.4.1.5504.4.7.2.1.10 | ColumnbridgeIfLearnMulticast | read-create | current | If true, snoop multicast packets for IGMP joins/leaves. |
| 1.3.6.1.4.1.5504.4.7.2.1.11 | ColumnbridgeIfForwardToUnicast | read-create | current | If true, attempt to forward via unicast MAC paths. |
| 1.3.6.1.4.1.5504.4.7.2.1.12 | ColumnbridgeIfForwardToMulticast | read-create | current | If true, attempt to forward via multicast MAC paths. |
| 1.3.6.1.4.1.5504.4.7.2.1.13 | ColumnbridgeIfForwardToDefault | read-create | current | If true, attempt to forward via VLAN default paths. |
| 1.3.6.1.4.1.5504.4.7.2.1.14 | ColumnbridgeLowerIfIndex | read-create | current | An entry exists for each bridge interface in the system. Only Ifindex and lower if index is needed to create a row. |
| 1.3.6.1.4.1.5504.4.7.2.1.15 | ColumnbridgeIfRowStatus | read-create | current | This object is used to create and remove rows in the table. See bridgeInterfaceEntry description for minimum requirements. |
| 1.3.6.1.4.1.5504.4.7.2.1.16 | ColumnbridgeIfCustomDHCP | read-create | current | If TRUE, forwards broadcast DHCPOFFER or DHCPACK packets even if bridgeFilterBroadcast is TRUE for that interface. |
| 1.3.6.1.4.1.5504.4.7.2.1.17 | ColumnbridgeIfIngressPacketRuleGroupIndex | read-create | current | Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the ingress interface. |
| 1.3.6.1.4.1.5504.4.7.2.1.18 | ColumnbridgeIfVlanIdCOS | read-create | current | The Class-Of-Service (COS) value used for VLAN Tag Insertion. |
| 1.3.6.1.4.1.5504.4.7.2.1.19 | ColumnbridgeIfOutgoingCOSOption | read-create | current | Determines COS setting on packets bridged out this interface. disable - COS setting is untouched. all - COS will be set to bridgeIfOutgoingCOSValue. |
| 1.3.6.1.4.1.5504.4.7.2.1.20 | ColumnbridgeIfOutgoingCOSValue | read-create | current | The COS value loaded into outgoing tagged packets. Applicable only if interface sends tagged packets and bridgeIfOutgoingCOSOption is outgoingCOSOption_all. |
| 1.3.6.1.4.1.5504.4.7.2.1.21 | ColumnbridgeIfStagTPID | read-create | current | The value of the tag protocol identifier that is being used for QinQ packets. (0x8100 is default.) |
| 1.3.6.1.4.1.5504.4.7.2.1.22 | ColumnbridgeIfStagId | read-create | current | The s-tag value that we are expecting to put on packets that are Rxed on this interface. |
| 1.3.6.1.4.1.5504.4.7.2.1.23 | ColumnbridgeIfStagStripAndInsert | read-create | current | If true, enable S-tag tagging on this IF. |
| 1.3.6.1.4.1.5504.4.7.2.1.24 | ColumnbridgeIfStagOutgoingCOSOption | read-create | current | Determines s-tag COS settings on packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with s_tagOut… |
| 1.3.6.1.4.1.5504.4.7.2.1.25 | ColumnbridgeIfStagCOS | read-create | current | The s-tag COS to be used when doing s-tag insertion. |
| 1.3.6.1.4.1.5504.4.7.2.1.26 | ColumnbridgeIfStagOutgoingCOSValue | read-create | current | The s-tag COS value loaded into outgoing tagged packets. Applicaple only if interface sends S-tagged packets and s_tagOutgoingCOSOption is All. |
| 1.3.6.1.4.1.5504.4.7.2.1.27 | ColumnbridgeIfMcastControlList | read-create | current | List of mcast-control-ids this bridge-interface-record is associated with. It is an integer stored as string, and controls which channels a user can watch. Not… |
| 1.3.6.1.4.1.5504.4.7.2.1.28 | ColumnbridgeIfMaxVideoStreams | read-create | current | Maximum number of multicast (video) streams that we will support. |
| 1.3.6.1.4.1.5504.4.7.2.1.29 | ColumnbridgeIfIsPPPoA | read-create | current | If true, this interface accepts PPPoA packets and will bridge them out as PPPoE packets. |
| 1.3.6.1.4.1.5504.4.7.2.1.30 | ColumnbridgeIfFloodUnknown | read-create | current | If true, flood frames with unknown unicast MAC address that would otherwise be discarded. |
| 1.3.6.1.4.1.5504.4.7.2.1.31 | ColumnbridgeIfFloodMulticast | read-create | current | If true, flood all multicast traffic received on this bridge to all other ports on this vlan. |
| 1.3.6.1.4.1.5504.4.7.2.1.32 | ColumnbridgeIfEgressPacketRuleGroupIndex | read-create | current | Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the egress interface. |
| 1.3.6.1.4.1.5504.4.7.2.1.33 | ColumnbridgeIfTableBasedFilter | read-create | current | none : Dynamic IP Filtering on bridge based on DHCP, is disabled. BIT 1(mac) : MAC address based Filtering based on DHCP, is enabled. BIT 2(ip) : IP address ba… |
| 1.3.6.1.4.1.5504.4.7.2.1.34 | ColumnbridgeIfDhcpLearn | read-create | current | none :IP address and Mac address are not learned from DHCP packets. BIT 1 (mac): MAC addresses are learned from DHCP packets. ip 2 (ip) : IP addresses are lear… |
| 1.3.6.1.4.1.5504.4.7.2.1.35 | ColumnbridgeIfOnDemandStatsEnabled | read-create | current | If true, the on-demand stats collection for this bridge interface will be enabled and packets will be counted. If bytes, the on-demand stats collection for thi… |
| 1.3.6.1.4.1.5504.4.7.2.1.36 | ColumnbridgeIfMvrVlan | read-create | current | The Multicast Vlan Registration (MVR) vlan ID. Multicast video packets with this vlan can be vlan translated out this bridge. |
| 1.3.6.1.4.1.5504.4.7.2.1.37 | ColumnbridgeIfVlanXlateFrom | read-create | current | If a packet's VLAN ID value matches this object's value then the packet's VLAN ID will be translated to the value of bridgeIfVlanId. A zero value disables tran… |
| 1.3.6.1.4.1.5504.4.7.2.1.38 | ColumnbridgeIfSlanXlateFrom | read-create | current | If a packet's SLAN ID value matches this object's value then the packet's SLAN ID will be translated to the value of bridgeIfStagId. A zero value disables tran… |
| 1.3.6.1.4.1.5504.4.7.2.1.39 | ColumnbridgeIfBridgeState | read-create | current | Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N/S ready(9… |
| 1.3.6.1.4.1.5504.4.7.2.1.40 | ColumnbridgeIfUnblock | read-write | current | Set to TRUE to unblock a bridge that is blocked due to flapping. |
| 1.3.6.1.4.1.5504.4.7.2.1.41 | ColumnbridgeType | read-create | current | bridge type |
| 1.3.6.1.4.1.5504.4.7.2.1.42 | ColumnbridgeIfGponGemPortId | read-write | current | GPON GEM Port ID used only to create a bridge on a GPON ONU. |
| 1.3.6.1.4.1.5504.4.7.2.1.43 | ColumnbridgeIfGponTrafficProfile | read-write | current | GPON Traffic Profile Index used only to create a bridge on a GPON ONU. |
| 1.3.6.1.4.1.5504.4.7.2.1.44 | ColumnbridgeIfIncomingCOSOption | read-write | current | Determines COS settings on incoming packets bridged out this interface: disable - COS replcement feature is disabled all - COS will be set with vlanIDCOS. |
| 1.3.6.1.4.1.5504.4.7.2.1.45 | ColumnbridgeIfStagIncomingCOSOption | read-write | current | Determines s-tag COS settings on incoming packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with… |
| 1.3.6.1.4.1.5504.4.7.3 | TablestaticBridgeTable | not-accessible | current | A collection of staticBridgeEntries. |
| 1.3.6.1.4.1.5504.4.7.3.1 | RowstaticBridgeEntry | not-accessible | current | Static Bridge entries are created by the user in order to specify forwarding for a particular interface, vlanId, mac address or ip address, slanId (for QinQ). … |
| 1.3.6.1.4.1.5504.4.7.3.1.1 | ColumnstaticBridgeMacOrIpAddress | not-accessible | current | If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this fi… |
| 1.3.6.1.4.1.5504.4.7.3.1.2 | ColumnstaticBridgeAddressType | not-accessible | current | If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpA… |
| 1.3.6.1.4.1.5504.4.7.3.1.3 | ColumnstaticBridgeMulticastAging | read-create | current | Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table… |
| 1.3.6.1.4.1.5504.4.7.3.1.4 | ColumnstaticBridgeRowStatus | read-create | current | Used to create, modify or delete an entry in this table. |
| 1.3.6.1.4.1.5504.4.7.3.1.5 | ColumnstaticBridgeFlapControl | read-create | current | This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) … |
| 1.3.6.1.4.1.5504.4.7.3.1.6 | ColumnstaticBridgeUnicastAging | read-create | current | Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table… |
| 1.3.6.1.4.1.5504.4.7.3.1.7 | ColumnstaticBridgeIgmpQueryInterval | read-create | current | How often (in seconds) we as a bridge inject IGMP query values into the stream. |
| 1.3.6.1.4.1.5504.4.7.3.1.8 | ColumnstaticBridgeFlags | read-create | current | none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondT… |
| 1.3.6.1.4.1.5504.4.7.3.1.9 | ColumnstaticBridgeIgmpCustomIpAddress | read-create | current | Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge. |
| 1.3.6.1.4.1.5504.4.7.3.1.10 | ColumnstaticBridgeLoopPrevention | read-write | current | This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates '… |
| 1.3.6.1.4.1.5504.4.7.3.1.11 | ColumnstaticBridgeIgmpDscp | read-create | current | This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (00101… |
| 1.3.6.1.4.1.5504.4.7.4 | TablebridgeIfLookupTable | not-accessible | current | A collection of bridgeIfLookupTable entries. |
| 1.3.6.1.4.1.5504.4.7.4.1 | RowbridgeIfLookupEntry | not-accessible | current | Bridge IfLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac addres… |
| 1.3.6.1.4.1.5504.4.7.4.1.1 | ColumnbridgeIfAddressType | not-accessible | current | If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress a… |
| 1.3.6.1.4.1.5504.4.7.4.1.2 | ColumnbridgeIfMacOrIpAddress | not-accessible | current | If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress r… |
| 1.3.6.1.4.1.5504.4.7.4.1.3 | ColumnbridgeIfLookupStaticOrDynamic | read-only | current | If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table ent… |
| 1.3.6.1.4.1.5504.4.7.4.1.4 | ColumnbridgeIfLookupFlush | read-write | current | The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of a… |
| 1.3.6.1.4.1.5504.4.7.5 | TablebridgeAddressLookupTable | not-accessible | current | A collection of bridgeAddressLookupTable entries. |
| 1.3.6.1.4.1.5504.4.7.5.1 | RowbridgeAddressLookupEntry | not-accessible | current | BridgeAddressLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac ad… |
| 1.3.6.1.4.1.5504.4.7.5.1.1 | ColumnbridgeAddressLookupStaticOrDynamic | read-only | current | If bridgeAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeAddressLookupStaticOrDynamic is set to 2, then this… |
| 1.3.6.1.4.1.5504.4.7.5.1.2 | ColumnbridgeAddressLookupFlush | read-write | current | The object 'bridgeIfAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used t… |
| 1.3.6.1.4.1.5504.4.7.6 | NodepacketRuleGroup | |||
| 1.3.6.1.4.1.5504.4.7.6.1 | ScalarpacketRuleGroupIndexNext | read-only | current | A scalar representing the next available Group Index for Packet Rule Table Entries. |
| 1.3.6.1.4.1.5504.4.7.6.2 | TablepacketRuleGroupNextIndexTable | not-accessible | current | A collection of entries each representing the next available index for that group. |
| 1.3.6.1.4.1.5504.4.7.6.2.1 | RowpacketRuleGroupNextIndexEntry | not-accessible | current | A packetRuleGroupNextIndexEntry contains the next available index for that packetRuleGroup. |
| 1.3.6.1.4.1.5504.4.7.6.2.1.1 | ColumnpacketRuleGroupMemberNextIndex | read-only | current | The next index available in a given packetRuleGroup for a new packetRuleEntry. |
| 1.3.6.1.4.1.5504.4.7.6.3 | TablepacketRuleTable | not-accessible | current | A collection of packetRuleEntries. |
| 1.3.6.1.4.1.5504.4.7.6.3.1 | RowpacketRuleEntry | not-accessible | current | Packet Rule entries are created by the user in order to specify filtering or other packet manipulation for a particular interface. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.1 | ColumnpacketRuleGroupMemberIndex | not-accessible | current | The index of a packetRuleEntry in a given packetRuleGroup. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.2 | ColumnpacketRuleType | read-create | current | A 32-bit value which determines a filter to be applied to packets on the interface matching the pattern specified in packetRuleValue. The size and offset of th… |
| 1.3.6.1.4.1.5504.4.7.6.3.1.3 | ColumnpacketRuleValue | read-create | current | A variable-length field whose meaning depends on packetRuleType. If bridgeForbidOui, it specifies a bit pattern to be matched in a packet, stored as a string, … |
| 1.3.6.1.4.1.5504.4.7.6.3.1.4 | ColumnpacketRuleRowStatus | read-create | current | This object is used to create and remove rows in the table. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.5 | ColumnpacketRuleValue2 | read-create | current | A variable-length field whose meaning depends on packetRuleType. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.6 | ColumnpacketRuleValue3 | read-create | current | A variable-length field whose meaning depends on packetRuleType. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.7 | ColumnpacketRuleValue4 | read-create | current | A variable-length field whose meaning depends on packetRuleType. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.8 | ColumnpacketRuleValue5 | read-create | current | A variable-length field whose meaning depends on packetRuleType. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.9 | ColumnpacketRuleGroupIndex | not-accessible | current | A scalar representing the Group Index for a set of Packet Rule Table Entries. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.10 | ColumnpacketRuleValue6 | read-create | current | A variable-length field whose meaning depends on packetRuleType. |
| 1.3.6.1.4.1.5504.4.7.6.3.1.11 | ColumnpacketRuleValue7 | read-create | current | A variable-length field whose meaning depends on packetRuleType. |
| 1.3.6.1.4.1.5504.4.7.7 | TablebridgePPPoETable | not-accessible | current | For PPPoA-to-PPPoE tables, provide a lookup by ifIndex into the PPPoE tables. If the session has not been created for this PPPoA ifIndex, then there will be no… |
| 1.3.6.1.4.1.5504.4.7.7.1 | RowbridgePPPoEEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.5504.4.7.7.1.1 | ColumnbridgePPPoEBrasMac | read-only | current | Destination mac address. |
| 1.3.6.1.4.1.5504.4.7.7.1.2 | ColumnbridgePPPoELocalHostMac | read-only | current | Source mac address. |
| 1.3.6.1.4.1.5504.4.7.7.1.3 | ColumnbridgePPPoEEIfIndex | read-only | current | PPPoE port's ifIndex. |
| 1.3.6.1.4.1.5504.4.7.7.1.4 | ColumnbridgePPPoESessionID | read-only | current | PPPoE session ID. |
| 1.3.6.1.4.1.5504.4.7.7.1.5 | ColumnbridgePPPoESlanId | read-only | current | SLan ID of BRAS. |
| 1.3.6.1.4.1.5504.4.7.7.1.6 | ColumnbridgePPPoEVlanId | read-only | current | VLAN ID of BRAS. |
| 1.3.6.1.4.1.5504.4.7.7.1.7 | ColumnbridgePPPoEEncapLLC | read-only | current | PPPoA encapsulation |
| 1.3.6.1.4.1.5504.4.7.8 | NodestpParam | |||
| 1.3.6.1.4.1.5504.4.7.8.1 | ScalarstpParamName | read-write | current | set this field if you are using MSTP, use the name of the bridge as a key. |
| 1.3.6.1.4.1.5504.4.7.8.2 | ScalarstpParamRevision | read-write | current | This parameter is used if you are running MSTP only. Currently we don't support any revisions to MSTP, so revision 0 is default. |
| 1.3.6.1.4.1.5504.4.7.8.3 | ScalarstpParamBridgePriority | read-write | current | The priority ID that will be advertised for this bridge. |
| 1.3.6.1.4.1.5504.4.7.8.4 | ScalarstpParamForceVersion | read-write | current | The protocol to initiate with. 3- MSTP, 2- RSTP, 0- STP. |
| 1.3.6.1.4.1.5504.4.7.8.5 | ScalarstpParamFwdDelay | read-write | current | The delay used by STP bridges to transition Root and Designated Ports to Forwarding. |
| 1.3.6.1.4.1.5504.4.7.8.6 | ScalarstpParamHelloTime | read-write | current | The interval between periodic transmissions of Configuration Messages by Designated Ports. We only support a hello time of 2 currently. |
| 1.3.6.1.4.1.5504.4.7.8.7 | ScalarstpParamMigrateTime | read-write | current | The initial value of the mdelayWhile and edgeDelayWhile timers. We currently only support a value of 3 for this timer. |
| 1.3.6.1.4.1.5504.4.7.8.8 | ScalarstpParamTxHoldCount | read-write | current | The transmit hold count is used by the Port Transmit state machine to limit transmission rate. |
| 1.3.6.1.4.1.5504.4.7.8.9 | ScalarstpParamMaxAge | read-write | current | The maximum age of the information transmitted by the bridge when it is the Root Bridge. |
| 1.3.6.1.4.1.5504.4.7.9 | TablestpBindTable | not-accessible | current | The stpBind table is used to store the entries of stpBind which hold the relationship between the ifIndex on which STP is to run on, and the MSTP instance if a… |
| 1.3.6.1.4.1.5504.4.7.9.1 | RowstpBindEntry | not-accessible | current | stpBindEntry is used to specify the type of STP that is to run on an ifIndex. An InstanceID of 0 specifies RSTP. An InstanceId > 0 indicates MSTP. |
| 1.3.6.1.4.1.5504.4.7.9.1.1 | ColumnstpBindInstanceID | not-accessible | current | This is a hidden storage of the InstanceId of an entry. |
| 1.3.6.1.4.1.5504.4.7.9.1.2 | ColumnstpBindRowStatus | read-create | current | Description. |
| 1.3.6.1.4.1.5504.4.7.9.1.3 | ColumnstpBindPortPriority | read-create | current | PortPriority is used to specify the STP priority of this port. |
| 1.3.6.1.4.1.5504.4.7.10 | TablemstpInstanceTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.5504.4.7.10.1 | RowmstpInstanceEntry | not-accessible | current | Description. |
| 1.3.6.1.4.1.5504.4.7.10.1.1 | ColumnmstpInstanceRowStatus | read-create | current | Description. |
| 1.3.6.1.4.1.5504.4.7.10.1.2 | ColumnmstpInstanceName | read-create | current | A name for this mstp instance and vlanId. |
| 1.3.6.1.4.1.5504.4.7.11 | TablebridgeStatsTable | not-accessible | current | The bridgeStatsTable is used to access the statistics of the entries in the bridge table. |
| 1.3.6.1.4.1.5504.4.7.11.1 | RowbridgeStatsEntry | not-accessible | current | Displays the bridge statistics table entries. |
| 1.3.6.1.4.1.5504.4.7.11.1.1 | ColumnbridgeStatsUcastRcvd | read-only | current | Unicast packets received. |
| 1.3.6.1.4.1.5504.4.7.11.1.2 | ColumnbridgeStatsMcastRcvd | read-only | current | Multicast packets received. |
| 1.3.6.1.4.1.5504.4.7.11.1.3 | ColumnbridgeStatsBcastRcvd | read-only | current | Broadcast packets received. |
| 1.3.6.1.4.1.5504.4.7.11.1.4 | ColumnbridgeStatsUcastSent | read-only | current | Unicast packets sent. |
| 1.3.6.1.4.1.5504.4.7.11.1.5 | ColumnbridgeStatsMcastSent | read-only | current | Multicast packets sent. |
| 1.3.6.1.4.1.5504.4.7.11.1.6 | ColumnbridgeStatsBcastSent | read-only | current | Broadcast packets sent. |
| 1.3.6.1.4.1.5504.4.7.11.1.7 | ColumnbridgeStatsErrorSent | read-only | current | Error packets sent. |
| 1.3.6.1.4.1.5504.4.7.11.1.8 | ColumnbridgeOnDemandStatsRulesSupported | read-only | current | Get the number of supported Ingress Stats available for a line card. |
| 1.3.6.1.4.1.5504.4.7.11.1.9 | ColumnbridgeOnDemandStatsRulesRemaining | read-only | current | Get the number of remaining Ingress Stats available for a line card |
| 1.3.6.1.4.1.5504.4.7.11.1.10 | ColumnbridgeStatsBSDUcastBlocked | read-only | current | Number of unicast packets dropped due to Bridge Packet Storm Detection threshold exceeded. |
| 1.3.6.1.4.1.5504.4.7.11.1.11 | ColumnbridgeStatsBSDMcastBlocked | read-only | current | Number of multicast packets dropped due to Bridge Packet Storm Detection threshold exceeded. |
| 1.3.6.1.4.1.5504.4.7.11.1.12 | ColumnbridgeStatsBSDBcastBlocked | read-only | current | Number of broadcast packets dropped due to Bridge Packet Storm Detection threshold exceeded. |
| 1.3.6.1.4.1.5504.4.7.11.1.13 | ColumnbridgeStatsBSDAlarmCount | read-only | current | This counter reflects the number of times this interface has transitioned to the alarm state due to the Bridge Packet Storm Detection threshold being exceeded … |
| 1.3.6.1.4.1.5504.4.7.11.1.14 | ColumnbridgeStatsBytesRcvdCount | read-only | current | This is a count of the number of bytes received. On-demand stats must be enabled for byte counters otherwise this counter is zero. |
| 1.3.6.1.4.1.5504.4.7.11.1.15 | ColumnbridgeStatsBytesSentCount | read-only | current | This is a count of the number of bytes transmitted. On-demand stats must be enabled for byte counters otherwise this counter is zero. |
| 1.3.6.1.4.1.5504.4.7.11.1.16 | ColumnbridgeStatsTicksLastCleared | read-only | current | Linecard tick value when bridge was last cleared. |
| 1.3.6.1.4.1.5504.4.7.11.1.17 | ColumnbridgeStatsTicksNow | read-only | current | Linecard current tick value. |
| 1.3.6.1.4.1.5504.4.7.11.1.18 | ColumnbridgeStatsTicksPerSecond | read-only | current | Linecard current tick value. |
| 1.3.6.1.4.1.5504.4.7.12 | NodebridgeCmd | |||
| 1.3.6.1.4.1.5504.4.7.12.1 | ScalarbridgeCmdOperation | read-write | current | Bridge command ID value. |
| 1.3.6.1.4.1.5504.4.7.12.2 | ScalarbridgeCmdFilterMask | read-write | current | Bridge command filters bit mask. If a bridge filter is enabled then the associated bridge filter value must be included in the SNMP packet. If the bridge filte… |
| 1.3.6.1.4.1.5504.4.7.12.3 | ScalarbridgeCmdIfIndex | read-write | current | Bridge command 'ifIndex' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (brid… |
| 1.3.6.1.4.1.5504.4.7.12.5 | ScalarbridgeCmdVlanId | read-write | current | Bridge command 'VLAN' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeC… |
| 1.3.6.1.4.1.5504.4.7.12.6 | ScalarbridgeCmdSlanId | read-write | current | Bridge command 'SLAN' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeC… |
| 1.3.6.1.4.1.5504.4.7.12.7 | ScalarbridgeCmdSlot | read-write | current | Bridge command 'SLOT' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeC… |
| 1.3.6.1.4.1.5504.4.7.12.8 | ScalarbridgeCmdPort | read-write | current | Bridge command 'PORT' filter value. This is the ifIndex of the linegroup on which the bridge is stacked If this object is included in the SNMP packet then the … |
| 1.3.6.1.4.1.5504.4.7.12.9 | ScalarbridgeCmdIpAddress | read-write | current | Bridge command 'IP Address' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (b… |
| 1.3.6.1.4.1.5504.4.7.12.10 | ScalarbridgeCmdMacAddress | read-write | current | Bridge command 'MAC Address' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (… |
| 1.3.6.1.4.1.5504.4.7.13 | NodeeapsGroup | |||
| 1.3.6.1.4.1.5504.4.7.13.1 | TableeapsConfigTable | not-accessible | current | This table contains information required for the management of EAPS domains. |
| 1.3.6.1.4.1.5504.4.7.13.1.1 | RoweapsConfigEntry | not-accessible | current | An entry exists for each EAPS domain in the system. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.1 | ColumneapsConfigPrimaryPortLineGroup | accessible-for-notify | current | This object contains the line group IfIndex of the Primary EAPS Port. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.2 | ColumneapsConfigSecondaryPortLineGroup | accessible-for-notify | current | This object contains the line group IfIndex of the Secondary EAPS Port. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.3 | ColumneapsConfigControlVlan | accessible-for-notify | current | This object contains the VLAN ID of the control VLAN for this domain record. This is the VLAN ID used in EAPS control messages. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.4 | ColumneapsConfigIsMasterNode | read-create | current | If this value is True, then this record describes a Master Node. Otherwise, it describes a Transit Node. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.5 | ColumneapsConfigControlVlanPriority | read-create | current | This object contains the Priority of the Control Vlan. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.6 | ColumneapsConfigDomainName | read-create | current | This object contains the user assigned ASCII representation of the Domain Name for this record. This name must be unique device wide. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.7 | ColumneapsConfigMsgTxInterval | read-create | current | This object contains the interval, in seconds, that a node sends Health Messages on the ring. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.8 | ColumneapsConfigTimeout | read-create | current | On a Master Node, this object contains the timeout, in seconds, which the Master Node will report a Ring Fault if it does not receive a Health Message on the r… |
| 1.3.6.1.4.1.5504.4.7.13.1.1.9 | ColumneapsConfigMaxDroppedMessages | read-create | current | On a Master Node, this object contains the number of contigious Health messages that may be dropped before the node declared a Ring Fault. This object is not u… |
| 1.3.6.1.4.1.5504.4.7.13.1.1.10 | ColumneapsConfigSnmpTrap | read-create | current | If this object is set to True, then this node will send SNMP Traps on Ring State transition. |
| 1.3.6.1.4.1.5504.4.7.13.1.1.11 | ColumneapsConfigDomainEnable | read-create | current | If this value is TRUE, the EAPS state machine will transition through the initialization process to the Health state. It will begin passing Control Messages an… |
| 1.3.6.1.4.1.5504.4.7.13.1.1.12 | ColumneapsConfigRowStatus | read-create | current | This object is used to create and remove rows in the table. See eapsConfigEntry description for minimum requirements. |
| 1.3.6.1.4.1.5504.4.7.13.2 | TableeapsProtectedVlanTable | not-accessible | current | This table contains information required for the management of a list of protected VLAN's in an EAPS domains. |
| 1.3.6.1.4.1.5504.4.7.13.2.1 | RoweapsProtectedVlanEntry | not-accessible | current | An entry for each VLAN ranges that is to be protected in the EAPS domain. |
| 1.3.6.1.4.1.5504.4.7.13.2.1.1 | ColumneapsProtectedVlanEntryIndex | accessible-for-notify | current | This object is an index which indicates which entry in the Protected Vlan Table is being addressed. For example, a value of 5 would indicate that the 5th entry… |
| 1.3.6.1.4.1.5504.4.7.13.2.1.2 | ColumneapsProtectedVlanLowerRange | read-create | current | The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsPr… |
| 1.3.6.1.4.1.5504.4.7.13.2.1.3 | ColumneapsProtectedVlanUpperRange | read-create | current | The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsPr… |
| 1.3.6.1.4.1.5504.4.7.13.2.1.4 | ColumneapsProtectedVlanRowStatus | read-create | current | This object is used to create and remove rows in the table. See eapsProtectedVlanEntry description for minimum requirements. |
| 1.3.6.1.4.1.5504.4.7.13.2.1.5 | ColumneapsProtectedVlanDomainName | read-only | current | The domain name for the EAPS protected vlan entry. |
| 1.3.6.1.4.1.5504.4.7.13.3 | TableeapsStatusTable | not-accessible | current | This table contains status of each EAPS domain state machine. |
| 1.3.6.1.4.1.5504.4.7.13.3.1 | RoweapsStatusEntry | not-accessible | current | The entry contains status of the domain's state machine. |
| 1.3.6.1.4.1.5504.4.7.13.3.1.1 | ColumneapsPrevState | read-only | current | Previous state for the domain. |
| 1.3.6.1.4.1.5504.4.7.13.3.1.2 | ColumneapsState | read-only | current | Current state for the domain. |
| 1.3.6.1.4.1.5504.4.7.13.4 | TableeapsStatsTable | not-accessible | current | EAPS statistics table. |
| 1.3.6.1.4.1.5504.4.7.13.4.1 | RoweapsStatsEntry | not-accessible | current | Displays the EAPS statistic table entries. |
| 1.3.6.1.4.1.5504.4.7.13.4.1.1 | ColumneapsStatsTotCtrlMsgSent | read-write | current | Total EAPS control messages sent. |
| 1.3.6.1.4.1.5504.4.7.13.4.1.2 | ColumneapsStatsTotCtrlMsgRecvd | read-write | current | Total EAPS control messages received. |
| 1.3.6.1.4.1.5504.4.7.13.5 | IdentityeapsTrapPrefix | current | Place-holder object for EAPS traps, which must have a final digit of 0 in OID. | |
| 1.3.6.1.4.1.5504.4.7.13.5.0 | IdentityeapsTraps | current | Traps raised by EAPS state machine. | |
| 1.3.6.1.4.1.5504.4.7.13.5.0.1 | NotificationeapsStateChange | current | State changed in the node for the EAPS domain. | |
| 1.3.6.1.4.1.5504.4.7.13.5.0.2 | NotificationeapsFailTimerExpFlagSet | current | The eapsFailTimerExpFlagSet notification is generated when the EAPS domain's fail timer expires for the first time, while its state is not in Fail state. | |
| 1.3.6.1.4.1.5504.4.7.13.5.0.3 | NotificationeapsFailTimerExpFlagClear | current | Description. | |
| 1.3.6.1.4.1.5504.4.7.13.5.0.4 | NotificationeapsLinkDownRingComplete | current | If a transit is in Link-Down state, and it receives a Health-Check-Pdu from the Master indicating the ring is Complete, it means there is some problem with the… | |
| 1.3.6.1.4.1.5504.4.7.13.6 | TableeapsTopologyTable | not-accessible | current | EAPS topology table. |
| 1.3.6.1.4.1.5504.4.7.13.6.1 | RoweapsTopologyEntry | not-accessible | current | Displays the EAPS topology table entries. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.1 | ColumneapsTopologyRing | not-accessible | current | This represents the link as primary or secondary. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.2 | ColumneapsTopologyRowNumber | not-accessible | current | This represents the node number in the ring. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.3 | ColumneapsTopologyDomainName | read-only | current | This represents the domain name for this record. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.4 | ColumneapsTopologyMacAddr | read-only | current | macAddress of the element in the ring. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.5 | ColumneapsTopologyIpAddr | read-only | current | Ip addressed of the element in the ring. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.6 | ColumneapsTopologyType | read-only | current | This represents whether the node is master or transit. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.7 | ColumneapsTopologyPrimaryLinkName | read-only | current | This represents the primary link name. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.8 | ColumneapsTopologyPrimaryLinkState | read-only | current | This represents the primary link state. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.9 | ColumneapsTopologySecondaryLinkName | read-only | current | This represents the secondary link name. |
| 1.3.6.1.4.1.5504.4.7.13.6.1.10 | ColumneapsTopologySecondaryLinkState | read-only | current | This represents the secondary link state. |
| 1.3.6.1.4.1.5504.4.7.14 | TablebridgeIgmpStatsTable | not-accessible | current | The bridgeIgmpStatsTable is used to access the IGMP statistics for bridges. |
| 1.3.6.1.4.1.5504.4.7.14.1 | RowbridgeIgmpStatsEntry | not-accessible | current | The bridgeIgmpStatsEntry holds IGMP stats for a bridge interface. |
| 1.3.6.1.4.1.5504.4.7.14.1.1 | ColumngenQueryRx | read-only | current | general IGMP queries received. |
| 1.3.6.1.4.1.5504.4.7.14.1.2 | ColumngenQueryTx | read-only | current | general IGMP queries transmitted. |
| 1.3.6.1.4.1.5504.4.7.14.1.3 | ColumnspecQueryRx | read-only | current | Specific IGMP queries received. |
| 1.3.6.1.4.1.5504.4.7.14.1.4 | ColumnspecQueryTx | read-only | current | Specific IGMP queries transmitted. |
| 1.3.6.1.4.1.5504.4.7.14.1.5 | Columnv2ReportsRx | read-only | current | Version 2 reports received (JOINs). |
| 1.3.6.1.4.1.5504.4.7.14.1.6 | Columnv2ReportsTx | read-only | current | Version 2 reports sent. |
| 1.3.6.1.4.1.5504.4.7.14.1.7 | ColumnleavesRx | read-only | current | IGMP leaves received. |
| 1.3.6.1.4.1.5504.4.7.14.1.8 | ColumnleavesTx | read-only | current | IGMP leaves transmitted. |
| 1.3.6.1.4.1.5504.4.7.14.1.9 | ColumnunknownRx | read-only | current | Unknown IGMP packets received. |
| 1.3.6.1.4.1.5504.4.7.14.1.10 | ColumnerrorRx | read-only | current | IGMP packet is bad received. |
| 1.3.6.1.4.1.5504.4.7.14.1.11 | ColumnactChans | read-only | current | Number of active muticast channels. |
| 1.3.6.1.4.1.5504.4.7.14.1.12 | ColumnactHosts | read-only | current | Number of active multicast hosts. |
| 1.3.6.1.4.1.5504.4.7.14.1.13 | Columnv3GenQueryRx | read-only | current | Number of IGMP V3 Queries received. |
| 1.3.6.1.4.1.5504.4.7.14.1.14 | Columnv3GenQueryTx | read-only | current | Number of IGMP V3 queries sent. |
| 1.3.6.1.4.1.5504.4.7.14.1.15 | Columnv3SpecQueryRx | read-only | current | Number of IGMP V3 specific queries received. |
| 1.3.6.1.4.1.5504.4.7.14.1.16 | Columnv3SpecQueryTx | read-only | current | Number of IGMP V3 specific queries sent. |
| 1.3.6.1.4.1.5504.4.7.14.1.17 | Columnv3ReportsRx | read-only | current | Number of IGMP V3 reports received. |
| 1.3.6.1.4.1.5504.4.7.14.1.18 | Columnv3ReportsTx | read-only | current | Number of IGMP V3 reports sent. |
| 1.3.6.1.4.1.5504.4.7.15 | NodebridgeGroup | |||
| 1.3.6.1.4.1.5504.4.7.15.1 | IdentitybridgeTrapPrefix | current | Traps raised for bridge conditions. | |
| 1.3.6.1.4.1.5504.4.7.15.1.0 | IdentitybridgeTraps | current | Bridge traps go under here - extra layer needed to ensure '0' in OID. | |
| 1.3.6.1.4.1.5504.4.7.15.1.0.1 | NotificationbridgeLoopDetection | current | Trap when bridge is looping on flap. | |
| 1.3.6.1.4.1.5504.4.7.15.1.0.2 | NotificationbridgeStormDetection | current | Trap sent when a bridge packet storm is detected. | |
| 1.3.6.1.4.1.5504.4.7.16 | NodebridgeTrapObjects | |||
| 1.3.6.1.4.1.5504.4.7.16.1 | ScalarbridgeMacAddrString | accessible-for-notify | current | vlan/slan/macAddress for bridge |
| 1.3.6.1.4.1.5504.4.7.17 | TablebridgeIgmpTable | not-accessible | current | The bridgeIgmpTable is used to access the IGMP data for bridges for when IGMP is in proxy mode and the IGMP status must be obtained from the linecard. |
| 1.3.6.1.4.1.5504.4.7.17.1 | RowbridgeIgmpEntry | not-accessible | current | BridgeIgmpEntry contains the igmp multicast data information for a bridge, indexed by ifIndex, hostMac, and mcastMac. |
| 1.3.6.1.4.1.5504.4.7.17.1.1 | ColumnslanId | read-only | current | IGMP slan identifier. Maximum value 4090 as defined by MAX_VLAN_NUM. |
| 1.3.6.1.4.1.5504.4.7.17.1.2 | ColumnvlanId | read-only | current | IGMP vlan identifier. Maximum value 4090 as defined my MAX_VLAN_NUM |
| 1.3.6.1.4.1.5504.4.7.17.1.3 | ColumnmcastMac | read-only | current | IGMP Multicast MAC addressed to bridge port. |
| 1.3.6.1.4.1.5504.4.7.17.1.4 | ColumnmcastIP | read-only | current | IGMP Multicast IP addressed to bridge port. |
| 1.3.6.1.4.1.5504.4.7.17.1.5 | ColumnhostMac | read-only | current | MAC address of end device receiving multicast packets. |
| 1.3.6.1.4.1.5504.4.7.17.1.6 | ColumnlastJoinTimer | read-only | current | Count down timer before IGMP entry ages out. |
| 1.3.6.1.4.1.5504.4.7.18 | TablestaticBridgePathTable | not-accessible | current | A collection of staticBridgePathEntries. The StaticBridgePath OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries tlist[0] ifIndex ifIn… |
| 1.3.6.1.4.1.5504.4.7.18.1 | RowstaticBridgePathEntry | not-accessible | current | Static Path Bridge entries are created by the user in order to specify forwarding for a particular interface, vlanId, mac address or ip address, slanId (for Qi… |
| 1.3.6.1.4.1.5504.4.7.18.1.1 | ColumnstaticBridgePathMacOrIpAddress | not-accessible | current | If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this fi… |
| 1.3.6.1.4.1.5504.4.7.18.1.2 | ColumnstaticBridgePathAddressType | not-accessible | current | If staticBridgeIPv6AddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacO… |
| 1.3.6.1.4.1.5504.4.7.18.1.3 | ColumnstaticBridgePathMulticastAging | read-create | current | Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table… |
| 1.3.6.1.4.1.5504.4.7.18.1.4 | ColumnstaticBridgePathRowStatus | read-create | current | Used to create, modify or delete an entry in this table. |
| 1.3.6.1.4.1.5504.4.7.18.1.5 | ColumnstaticBridgePathFlapControl | read-create | current | This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) … |
| 1.3.6.1.4.1.5504.4.7.18.1.6 | ColumnstaticBridgePathUnicastAging | read-create | current | Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table… |
| 1.3.6.1.4.1.5504.4.7.18.1.7 | ColumnstaticBridgePathIgmpQueryInterval | read-create | current | How often (in seconds) we as a bridge inject IGMP query values into the stream. |
| 1.3.6.1.4.1.5504.4.7.18.1.8 | ColumnstaticBridgePathFlags | read-create | current | none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondT… |
| 1.3.6.1.4.1.5504.4.7.18.1.9 | ColumnstaticBridgePathIgmpCustomIpAddress | read-create | current | Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge. |
| 1.3.6.1.4.1.5504.4.7.18.1.10 | ColumnstaticBridgePathLoopPrevention | read-write | current | This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates '… |
| 1.3.6.1.4.1.5504.4.7.18.1.11 | ColumnstaticBridgePathIgmpDscp | read-create | current | This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (00101… |
| 1.3.6.1.4.1.5504.4.7.19 | TablebridgePathIfLookupTable | not-accessible | current | A collection of bridgePathIfLookupTable entries. The bridgePathIfLookup OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries tlist[0] ad… |
| 1.3.6.1.4.1.5504.4.7.19.1 | RowbridgePathIfLookupEntry | not-accessible | current | Bridge IfLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac addres… |
| 1.3.6.1.4.1.5504.4.7.19.1.1 | ColumnbridgePathIfAddressType | not-accessible | current | If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress a… |
| 1.3.6.1.4.1.5504.4.7.19.1.2 | ColumnbridgePathIfMacOrIpAddress | not-accessible | current | If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress r… |
| 1.3.6.1.4.1.5504.4.7.19.1.3 | ColumnbridgePathIfLookupStaticOrDynamic | read-only | current | If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table ent… |
| 1.3.6.1.4.1.5504.4.7.19.1.4 | ColumnbridgePathIfLookupFlush | read-write | current | The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of a… |
| 1.3.6.1.4.1.5504.4.7.20 | TablebridgePathAddressLookupTable | not-accessible | current | A collection of bridgePathAddressLookupTable entries. The bridgePathAddressLookup OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries t… |
| 1.3.6.1.4.1.5504.4.7.20.1 | RowbridgePathAddressLookupEntry | not-accessible | current | BridgePathAddressLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, ma… |
| 1.3.6.1.4.1.5504.4.7.20.1.1 | ColumnbridgePathAddressLookupStaticOrDynamic | read-only | current | If bridgePathAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgePathAddressLookupStaticOrDynamic is set to 2, t… |
| 1.3.6.1.4.1.5504.4.7.20.1.2 | ColumnbridgePathAddressLookupFlush | read-write | current | The object 'bridgePathAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used… |
| 1.3.6.1.4.1.5504.4.7.21 | TablebridgeStatusTable | not-accessible | current | This table contains runtime status for each bridge interface. |
| 1.3.6.1.4.1.5504.4.7.21.1 | RowbridgeStatusEntry | not-accessible | current | Runtime status data for a single bridge. |
| 1.3.6.1.4.1.5504.4.7.21.1.1 | ColumnbridgeStatusState | read-only | current | Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N/S ready(9… |
| 1.3.6.1.4.1.5504.6.77 | IdentitybridgeRecord | keyword | BRIDGE record MIB IP Software Minneapolis, MN | |
| 1.3.6.1.4.1.5504.9 | NodezhoneCompliances | |||
| 1.3.6.1.4.1.5504.9.1 | NodezhoneGroups | |||
| 1.3.6.1.4.1.5504.9.1.23 | GroupzhoneBridgeGroup | current | The list of zhone bridge objects. | |
| 1.3.6.1.4.1.5504.9.1.76 | GroupzhoneBridgeCmdGroup | current | Bridge CMD objects | |
| 1.3.6.1.4.1.5504.9.1.77 | GroupzhoneBridgeEapsGroup | current | EAPS objects | |
| 1.3.6.1.4.1.5504.9.1.78 | GroupzhoneBridgeEapsConfigGroup | current | EAPS config objects | |
| 1.3.6.1.4.1.5504.9.1.79 | GroupzhoneBridgeEapsTopologyGroup | current | EAPS Topology objects | |
| 1.3.6.1.4.1.5504.9.1.80 | GroupzhoneBridgeNotificationGroup | current | BRIDGE Notifications | |
| 1.3.6.1.4.1.5504.9.1.81 | GroupzhoneBridgeIgmpGroup | current | IGMP objects | |
| 1.3.6.1.4.1.5504.9.1.82 | GroupzhoneBridgeStatsGroup | current | Bridge STATS objects |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BridgeState | INTEGER { up(1), down(2), trouble(3), notAvailable(4), initializing(5), adminDown(6), adminStateTest(7), adminStateNone(8), ready(9), discovering(10), unknown(11), blocked(12), pending(13), disabled(14), learning(15), forwarding(16), blockedFlapping(17), blockedPersistent(18), blockedFlappingPersistent(19) } NetworkAddress ::= OCTET STRING | current | state as shown in 'bridge show'. |
| EapsState | INTEGER { idle(0), complete(1), failed(2), links-up(3), link-down(4), preForwarding(5), init(6) } | current | EAPS State Values (per RFC 3619bis). IDLE = 0x00 (EAPS Domain (Master/Transit) still not running) COMPLETE = 0x01 (Master in complete State) FAILED = 0x02 (Master in Failed State) LINKS-UP = 0x03 (Transit in links-up St… |
| PacketRuleGroupIndex | Integer32 (0..2147483647) | current | Description. |