ZHONE-SYSTEM-MIB
263 objects
This module contains the system generic variables that are complete for the entire system. Note that some functional entities are maintained in their own mib as they will be included only when their functionality is included for that particular Zhone platform.
Imported Objects
| IANAifType-MIB | IANAifType |
| IF-MIB | ifIndex InterfaceIndexOrZero |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DateAndTime TEXTUAL-CONVENTION TruthValue |
| Zhone | zhone zhoneModules zhoneShelfIndex zhoneSlotIndex zhoneSystem zhoneTrapModules |
| ZHONE-COM-IP-REC-MIB | ipIfAddr ipIfLgId ipIfVci ipIfVpi |
| ZHONE-INTERFACE-TRANSLATION-MIB | pportNumber subPortNumber zhoneShelfNumber zhoneSlotNumber |
| Zhone-TC | ZhoneAdminString ZhoneAlarmSeverity ZhoneAlarmTypeId ZhoneCardLineType ZhoneCardType ZhoneCountryCode ZhoneFileName ZhoneIfType ZhoneRowStatus ZhoneShelfValue ZhoneSlotValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5504.3.1.1 | IdentityzhoneZms | current | The following variables are associated with the state of existence and connectivity with the Zhone Management System (ZMS). | |
| 1.3.6.1.4.1.5504.3.1.1.1 | ScalarzhoneZmsExists | read-write | current | Identifies whether or not this device is being managed by the Zhone Management System. This is only settable by the management system and NOT by the CLI as it … |
| 1.3.6.1.4.1.5504.3.1.1.2 | ScalarzhoneZmsConnectionStatus | read-write | current | The status of the connection between this device and the Zhone Management System, if one exists. This value can either be set directly by ZMS or by the device … |
| 1.3.6.1.4.1.5504.3.1.1.3 | ScalarzhoneZmsIpAddress | read-write | current | This is the ZMS IP address for which configuration synchronization messages and any other special handling is performed. This can be set either via CLI or ZMS. |
| 1.3.6.1.4.1.5504.3.1.1.4 | ScalarzhoneZmsBlockCli | read-write | current | If TRUE, CLI only allows 'show' commands and cannot modify/add any data records. This is used by ZMS to prevent race conditions and to allow only single access… |
| 1.3.6.1.4.1.5504.3.1.2 | IdentityzhoneTraps | current | This is the trap information related to handling device to ZMS traps. | |
| 1.3.6.1.4.1.5504.3.1.2.1 | TablezhoneTrapsTable | not-accessible | current | Zhone Traps Table |
| 1.3.6.1.4.1.5504.3.1.2.1.1 | RowzhoneTrapsEntry | not-accessible | current | An entry per trap destination. |
| 1.3.6.1.4.1.5504.3.1.2.1.1.1 | ColumnzhoneTrapsDestination | not-accessible | current | The location to be send traps. |
| 1.3.6.1.4.1.5504.3.1.2.1.1.2 | ColumnzhoneTrapsCommunityName | read-create | current | Community name to be sent in all traps sent to this destination. This field is defaulted to NULL so a null string will be sent to the destination. |
| 1.3.6.1.4.1.5504.3.1.2.1.1.3 | ColumnzhoneTrapsSequenceNumber | read-only | current | Next sequence number to be sent as part of a trap generated by the device. The sequence number has two uses. In one case,it is the sequence number of the non-a… |
| 1.3.6.1.4.1.5504.3.1.2.1.1.4 | ColumnzhoneTrapsResendSequenceNumber | read-create | current | This is set by the ZMS in order to have the device resend saved traps because one or more were lost in transmission. The device will resend traps starting at t… |
| 1.3.6.1.4.1.5504.3.1.2.1.1.5 | ColumnzhoneTrapsAckedSequenceNumber | read-create | current | Acknowledged trap sequence number. This field is set by the ZMS in order to acknowledge a trap sent by the device with the Request Acknowledge flag set to YES.… |
| 1.3.6.1.4.1.5504.3.1.2.1.1.6 | ColumnzhoneTrapsSeverity | read-create | current | The Trap severity level which at this level or higher, traps will be sent to this destination. |
| 1.3.6.1.4.1.5504.3.1.2.1.1.7 | ColumnzhoneTrapsAllowedCategories | read-create | current | Array of allowed categories to be sent to this particular trap destination. This field is not currently implemented and is reserved for future use. |
| 1.3.6.1.4.1.5504.3.1.2.1.1.8 | ColumnzhoneTrapsAdminStatus | read-create | current | Whether traps should be enabled or disabled for this particular IP address. |
| 1.3.6.1.4.1.5504.3.1.2.1.1.9 | ColumnzhoneTrapsRowStatus | read-create | current | Row status in order to create the entry for this destination. There are no required fields on a create besides the obvious index of the ip address of the desti… |
| 1.3.6.1.4.1.5504.3.1.2.1.1.10 | ColumnzhoneTrapsGatewayTrapServerAddress | read-create | current | The Gateway Trap Server Address is used to locate the Gateway. Trap Server. This field is defaulted 0,0,0. |
| 1.3.6.1.4.1.5504.3.1.2.2 | ScalarzhoneTrapVersion | accessible-for-notify | current | Version number of the format of the trap. Any changes to the common area of a trap require a bump of this number. |
| 1.3.6.1.4.1.5504.3.1.2.3 | ScalarzhoneTrapFlags | accessible-for-notify | current | This variable is sent with all traps and contains flags related to this trap. trapAcknolwedge: If this bit is set, it indicates to the ZMS that the trap must b… |
| 1.3.6.1.4.1.5504.3.1.2.4 | ScalarzhoneTrapShelf | accessible-for-notify | current | This variable is sent with all traps. This contains the value of the shelf that originated the trap. |
| 1.3.6.1.4.1.5504.3.1.2.5 | ScalarzhoneTrapSlot | accessible-for-notify | current | This variable is sent with all traps. This contains the value of the slot that originated the trap. |
| 1.3.6.1.4.1.5504.3.1.2.6 | ScalarzhoneTrapPort | accessible-for-notify | current | This variable is sent with all traps. This contains the value of the port that originated the trap. If this is a system or card level trap (no port is associat… |
| 1.3.6.1.4.1.5504.3.1.2.7 | ScalarzhoneTrapSubPort | accessible-for-notify | current | This variable is sent with all traps. This contains the value of the subport that originated the trap. If this is a system or card level trap (no port is assoc… |
| 1.3.6.1.4.1.5504.3.1.2.8 | ScalarzhoneTrapProviderId | accessible-for-notify | current | Unique service provider ID. This value is used throughout the management system to link objects with customers or service providers. |
| 1.3.6.1.4.1.5504.3.1.2.9 | ScalarzhoneTrapText | accessible-for-notify | current | Any text associated with this trap. NULL is allowed |
| 1.3.6.1.4.1.5504.3.1.2.10 | ScalarzhoneTrapPortType | accessible-for-notify | current | This is the If Type. It is used to uniquely identify a port. |
| 1.3.6.1.4.1.5504.3.1.2.11 | ScalarzhoneTrapPortTypeExtension | accessible-for-notify | current | This is the If Type Extension. It is used to uniquely identify a port. |
| 1.3.6.1.4.1.5504.3.1.2.12 | ScalarzhoneTrapAlarmAction | accessible-for-notify | current | This is the alarm action type for products supporting the alarm manager functionality. |
| 1.3.6.1.4.1.5504.3.1.2.13 | ScalarzhoneTrapAlarmId | accessible-for-notify | current | For products supporting the alarm manager functionality, this is the alarm id a particular trap is setting or clearing. |
| 1.3.6.1.4.1.5504.3.1.2.14 | ScalarzhoneTrapAlarmSeverity | accessible-for-notify | current | For products supporting the alarm manager functionality, this is the alarm severity a particular trap is setting or clearing. |
| 1.3.6.1.4.1.5504.3.1.2.15 | ScalarzhoneTrapConfigSyncResetInterval | accessible-for-notify | current | The ConfigSync reset check is run in 6 minute intervals. This object represents the interval number and starts with interval number 1 at system bootup and will… |
| 1.3.6.1.4.1.5504.3.1.2.16 | ScalarzhoneTrapConfigSyncResetCount | accessible-for-notify | current | This count is the number of times the device has had to reset ConfigSync. Resetting configsync on the device consists of closing the FTP data and control socke… |
| 1.3.6.1.4.1.5504.3.1.2.17 | ScalarzhoneTrapConfigSyncResetLastFtpTime | accessible-for-notify | current | Last time device sent a ConfigSync Ftp command to ZMS. Measured using the Unix time() function. The internal representation of time is the number of seconds el… |
| 1.3.6.1.4.1.5504.3.1.2.18 | ScalarzhoneTrapConfigSyncResetCurrentTime | accessible-for-notify | current | Current device time returned using Unix time() function. The internal representation of time is the number of seconds elapsed since 00:00 Universal time on Jan… |
| 1.3.6.1.4.1.5504.3.1.2.19 | ScalarzhoneTrapUtcTime | accessible-for-notify | current | Number of seconds since Jan. 1, 1970 GMT, when this trap was sent from the device. |
| 1.3.6.1.4.1.5504.3.1.3 | IdentityzhoneConfigSync | current | Configuration Synchronization information. | |
| 1.3.6.1.4.1.5504.3.1.3.1 | ScalarzhoneConfigSyncExists | read-only | current | Indicates whether or not there exists records to be sent to the ZMS config synch manager for changes that have been made by CLI/HTTP to the data base. |
| 1.3.6.1.4.1.5504.3.1.3.2 | ScalarzhoneConfigSyncOverflow | read-only | current | Indicates whether or not the device had to discard update data base records due to resource constraints. If TRUE, traps will be sent to the ZMS Config Synch Ma… |
| 1.3.6.1.4.1.5504.3.1.3.3 | ScalarzhoneConfigSyncPriority | read-only | current | Indicates the highest priority configuration synchronization trap outstanding. This flag is set to none at boot time and whenever a file of synchronization cha… |
| 1.3.6.1.4.1.5504.3.1.3.4 | ScalarzhoneConfigSyncAction | read-write | current | Used by ZMS when it wants to create a list of config synch records. It must first write the filename expected and then set the action. The create_list action a… |
| 1.3.6.1.4.1.5504.3.1.3.5 | ScalarzhoneConfigSyncFileName | read-write | current | File Name to be used when creating the config synch records. |
| 1.3.6.1.4.1.5504.3.1.3.6 | ScalarzhoneConfigSyncStatus | read-only | current | Used by Config Sync Acgent when processing a request to create a list of config synch records. |
| 1.3.6.1.4.1.5504.3.1.3.7 | ScalarzhoneConfigSyncUserName | read-write | current | User Name to be used when sending the config synch records. When read, the last user name is returned. |
| 1.3.6.1.4.1.5504.3.1.3.8 | ScalarzhoneConfigSyncUserPassword | read-write | current | Password to be used when sending the config synch records. For use in FTP authentication. When read, always returns the NULL string |
| 1.3.6.1.4.1.5504.3.1.4 | IdentityzhoneAdmin | current | Zhone Authorization parameters. | |
| 1.3.6.1.4.1.5504.3.1.4.1 | TablezhoneAdminCommunityTable | not-accessible | current | Zhone proprietary Community Table. |
| 1.3.6.1.4.1.5504.3.1.4.1.1 | RowzhoneAdminCommunityEntry | not-accessible | current | A community name access to this system. |
| 1.3.6.1.4.1.5504.3.1.4.1.1.1 | ColumnzhoneAdminCommunityName | not-accessible | current | The community name that has access to this system. Maximum length for community name string is 32 characters. |
| 1.3.6.1.4.1.5504.3.1.4.1.1.2 | ColumnzhoneAdminCommunityAccess | read-create | current | The Access Rights for this particular community name. An access of read-write-admin allows access to those tables with a higher level of security such as the c… |
| 1.3.6.1.4.1.5504.3.1.4.1.1.3 | ColumnzhoneAdminCommunityAccessListIndex | read-create | current | The AccessList Table index indicating which IP addresses are allowed to use this community name. If the value is 0, no address checking is performed and all SN… |
| 1.3.6.1.4.1.5504.3.1.4.1.1.4 | ColumnzhoneAdminCommunityRowStatus | read-create | current | Row status in order to create the entry for this destination. |
| 1.3.6.1.4.1.5504.3.1.4.2 | ScalarzhoneNextAdminAccessIndex | read-only | current | The next available zhoneAdminAccessListIndex that can be used by the manager when creating a access list entry. A Get request to this field causes the current … |
| 1.3.6.1.4.1.5504.3.1.4.3 | TablezhoneAdminAccessListTable | not-accessible | current | Access List Table Definition. |
| 1.3.6.1.4.1.5504.3.1.4.3.1 | RowzhoneAdminAccessListEntry | not-accessible | current | Zhone Access List Entry Definition. |
| 1.3.6.1.4.1.5504.3.1.4.3.1.1 | ColumnzhoneAdminAccessListIndex | not-accessible | current | The index into this table. There is a maximum support of a total of 50 access lists. 0 is not supported as it indicates that no IP address validation should be… |
| 1.3.6.1.4.1.5504.3.1.4.3.1.2 | ColumnzhoneAdminAccessListIpAddress | not-accessible | current | The IP address is used as a index into this table and indicates whether SNMP requests originating from this address will be accepted. |
| 1.3.6.1.4.1.5504.3.1.4.3.1.3 | ColumnzhoneAdminAccessRowStatus | read-create | current | Row status in order to create the entry for this destination. |
| 1.3.6.1.4.1.5504.3.1.4.4 | IdentityzhoneUser | current | Zhone User parameters. | |
| 1.3.6.1.4.1.5504.3.1.4.4.1 | ScalarzhoneUserIdNext | read-only | current | The next available zhoneUserId that can be used by the manager when creating a user entry. A Get request to this field causes the current number to be returned… |
| 1.3.6.1.4.1.5504.3.1.4.4.2 | ScalarzhoneUserTotalFailedLogins | read-only | current | The number of failed logins performed by any user whether this be for invalid user id or valid user id but an invalid password. |
| 1.3.6.1.4.1.5504.3.1.4.4.3 | TablezhoneUserTable | not-accessible | current | ZLI user information. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1 | RowzhoneUserEntry | not-accessible | current | A row exists for each user that can login on this system. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.1 | ColumnzhoneUserId | not-accessible | current | The id used to identify this particular user. This value is only used for access to this table and is not externally shown. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.2 | ColumnzhoneUserName | read-create | current | The user name allowed to login to this system. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.3 | ColumnzhoneUserPassword | read-create | current | The password to be used for logging in to the system. This field is returned as an encrypted field. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.4 | ColumnzhoneUserPrompt | read-create | current | The prompt to be used after this user has logged in to the system. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.5 | ColumnzhoneUserAccessLevel | read-create | current | Array of access levels that a user may have. This is an OR field where a user may have access to different subsystems. Only exception is Admin access level whi… |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.6 | ColumnzhoneUserAdmin | read-create | current | Whether this user is enabled (i.e. can login). Disabling the user will automatically cause an internal logout if the user is currently logged in. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.7 | ColumnzhoneUserLogins | read-only | current | The number of successful logins performed by this user. |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.8 | ColumnzhoneUserFailedLogins | read-only | current | The number of failed logins performed by this user. A user would have had entered a this user name but entered an invalid password. Invalid user names are not … |
| 1.3.6.1.4.1.5504.3.1.4.4.3.1.9 | ColumnzhoneUserRowStatus | read-create | current | Row status in order to create the entry for this user. In order to successfully create a user record, the following variables are required: zhoneUserName zhone… |
| 1.3.6.1.4.1.5504.3.1.5 | IdentityzhoneSystemConfiguration | current | System configuration parameters | |
| 1.3.6.1.4.1.5504.3.1.5.1 | ScalarzhoneSystemConfigurationNumShelves | read-only | current | The number of shelves physically in the system |
| 1.3.6.1.4.1.5504.3.1.5.2 | ScalarzhoneSystemConfigurationShelvesArray | read-only | current | Bit array from 0-255 (32 8-bit bytes) that are present in the system. |
| 1.3.6.1.4.1.5504.3.1.5.3 | ScalarzhoneSystemConfigurationNumCards | read-only | current | The total number of cards in the system (physcially). The number per shelf is defined in the shelf mib. |
| 1.3.6.1.4.1.5504.3.1.5.4 | ScalarzhoneSystemConfigurationIpAddress | read-write | current | The IP address of this device. Independent of the different IP interfaces configured and what is active,a manager uses this address as how to address the devic… |
| 1.3.6.1.4.1.5504.3.1.5.5 | ScalarzhoneSystemConfigurationAlternateIpAddress | read-write | current | A second IP address of this device. Independent of the different IP interfaces configured and what is active,a manager uses this address as how to address the … |
| 1.3.6.1.4.1.5504.3.1.5.6 | ScalarzhoneSystemConfigurationDateAndTime | read-write | current | The date and time of the system, specified in local time. Only a community name having 'admin' priviledges will be allowed to modify this value. Although any v… |
| 1.3.6.1.4.1.5504.3.1.5.7 | ScalarzhoneSystemConfigurationCountryRegion | read-write | current | The country or region where this system is operating in. This variable is used to adjust system settings for different functional modules. For example, both DS… |
| 1.3.6.1.4.1.5504.3.1.5.8 | ScalarzhonePrimaryClockSource | read-write | deprecated | The ifIndex of the interface from which clock can be derived. Only oc3, ds1, and ds3 interfaces can be used for this. This interface will be used to drive the … |
| 1.3.6.1.4.1.5504.3.1.5.9 | ScalarzhoneSystemConfigurationRingSource | read-write | current | Ring voltage source selection (internal or external): (1)Select internal ring generator (located within TAC) as source for ring voltage to line cards. (2) Sele… |
| 1.3.6.1.4.1.5504.3.1.5.10 | ScalarzhoneSystemCurrentClockSource | read-only | current | The current interface that is being used for the clock source. A value of 0 is returned if there are no available interfaces in the zhoneSystemClockTable that … |
| 1.3.6.1.4.1.5504.3.1.5.11 | ScalarzhoneSystemSecondaryClockSource | read-only | current | The interface that would next be used for the system clock source if the zhoneSystemCurrentClockSource becomes inactive, it's elgibility is changed,is being us… |
| 1.3.6.1.4.1.5504.3.1.5.12 | TablezhoneSystemClockTable | not-accessible | current | Table of physical ports that could be used as the clock source for other physical ports (i.e. DSL, DS1/DS3, and sonet). Entries are added to this table automat… |
| 1.3.6.1.4.1.5504.3.1.5.12.1 | RowzhoneSystemClockEntry | not-accessible | current | A row in the system clock table. Each row represents a possible clock source by it's associated ifIndex. |
| 1.3.6.1.4.1.5504.3.1.5.12.1.1 | ColumnzhoneSystemClockEligibility | read-write | current | The eligibility field indicates whether the system should include this physical port as a possible clock source. |
| 1.3.6.1.4.1.5504.3.1.5.12.1.2 | ColumnzhoneSystemClockWeight | read-write | current | The weight to be used to indicate the preference for each eligible port which is currently active (zhoneSystemClockElgibilityStatus = active) to be used as the… |
| 1.3.6.1.4.1.5504.3.1.5.12.1.3 | ColumnzhoneSystemClockAvailabilityStatus | read-only | current | The status for whether this port can be usd as a clock source. A port can be active only on all of the following conditions are true: 1. zhoneSystemClockEligib… |
| 1.3.6.1.4.1.5504.3.1.5.12.1.4 | ColumnzhoneSystemClockTxClockMode | read-only | current | The transmit clock source is provisioned in the profile corresponding to the line type. The choices are loop, local, or through. zhoneSystemClockTxClockMode sh… |
| 1.3.6.1.4.1.5504.3.1.5.13 | ScalarzhoneSystemConsoleLogging | read-write | current | An option to enable or disable logging of system messages onto the console. |
| 1.3.6.1.4.1.5504.3.1.5.14 | ScalarzhoneSystemRevertiveClockSource | read-write | current | Indicates whether revertive behavior of the system clock is desired. If set to TRUE, the system will automatically revert to the higher weighted clock when it … |
| 1.3.6.1.4.1.5504.3.1.5.15 | ScalarzhoneSystemVoiceBandwidthCheck | read-write | current | Turns ON (true) of OFF (false) ATM bandwidth checks for new voice calls going through the system. The bandwidth check is based on the configuration of the Rx a… |
| 1.3.6.1.4.1.5504.3.1.5.16 | ScalarzhoneAlarmLevelsEnabled | read-write | current | Bit field indicating which combination of the 4 alarm levels are enabled. User can disable alarms based on alarm severity level. |
| 1.3.6.1.4.1.5504.3.1.5.17 | ScalarzhoneSystemUserAuthMethod | read-write | current | This object determines how users access to the device is authenticated. A value of local indicates that user should be authenticated using locally provisioned … |
| 1.3.6.1.4.1.5504.3.1.5.18 | ScalarzhoneSystemRadiusAuthIndex | read-write | current | This object contains the index of the Radius Server profile to be used if RADIUS authentication is desired. |
| 1.3.6.1.4.1.5504.3.1.5.19 | ScalarzhoneSystemSecureFTP | read-write | current | Secure FTP (SFTP) control. |
| 1.3.6.1.4.1.5504.3.1.5.20 | ScalarzhoneSystemWebInterface | read-write | current | Specifies whether the Web GUI Interface is enabled for this system. |
| 1.3.6.1.4.1.5504.3.1.5.21 | ScalarzhoneSystemConfigurationOptions | read-write | current | System options in bit-mask format. |
| 1.3.6.1.4.1.5504.3.1.5.22 | ScalarzhoneSystemConfigurationReservedVlanIdStart | read-write | current | Starting VLAN ID of the reserved VLAN ID block. The reserved VLAN ID block starts with the reservedVlanIdStart and ends with reservedVlanIdStart + reservedVlan… |
| 1.3.6.1.4.1.5504.3.1.5.23 | ScalarzhoneSystemConfigurationReservedVlanIdCount | read-write | current | Number of reserved VLAN IDs in the reserved VLAN ID block. A zero value disables these reserved VLANs and operation reverts to normal VLAN ID reservation. The … |
| 1.3.6.1.4.1.5504.3.1.5.24 | ScalarzhoneSystemSnmpVersion | read-write | current | Version of SNMP the supported by the device. |
| 1.3.6.1.4.1.5504.3.1.5.25 | ScalarzhoneSystemPersistentLogging | read-write | current | An option to enable or disable persistent logging of system messages onto the console. |
| 1.3.6.1.4.1.5504.3.1.5.26 | ScalarzhoneSystemOutletTemperatureHighThreshold | read-write | current | Specifies the outlet sensor high temperature threshold. Minor, Major & Critical alarms will be raised when outlet sensor temperature reaches X, X+5 & X+10 resp… |
| 1.3.6.1.4.1.5504.3.1.5.27 | ScalarzhoneSystemOutletTemperatureLowThreshold | read-write | current | Specifies the outlet sensor low temperature threshold. Minor alarm will be raised when outlet sensor reaches the temperatue configured in this field |
| 1.3.6.1.4.1.5504.3.1.6 | TablezhoneSoftwareLoadTable | not-accessible | current | This table is used by the system to determine the default code image to load for each card type. Each card, when it requests a software load, will either recei… |
| 1.3.6.1.4.1.5504.3.1.6.1 | RowzhoneSoftwareLoadEntry | not-accessible | current | Table of software code image names for each card type in a BAN. |
| 1.3.6.1.4.1.5504.3.1.6.1.1 | ColumnzhoneSwCardType | not-accessible | current | Type of card requesting software load this card type the same used in the Card Resources MIB. |
| 1.3.6.1.4.1.5504.3.1.6.1.2 | ColumnzhoneSwCardSwFileName | read-create | current | Name of code image to loaded by software load services for the card type requesting a load if a specific load version is not requested. Required for RowCreate |
| 1.3.6.1.4.1.5504.3.1.6.1.3 | ColumnzhoneSwLoadRowStatus | read-create | current | Row status in order to create the entry for this destination. zhoneCardSwFileName is required for row creation. |
| 1.3.6.1.4.1.5504.3.1.7 | TablezhoneSnmpErrorTable | not-accessible | current | Zhone SNMP error information. |
| 1.3.6.1.4.1.5504.3.1.7.1 | RowzhoneSnmpErrorEntry | not-accessible | current | A single entry in the error table which describes an problem detected by the mib handler. |
| 1.3.6.1.4.1.5504.3.1.7.1.1 | ColumnzhoneSnmpErrorIpAddress | not-accessible | current | The IP address of the requesting station for which this error is applicable. |
| 1.3.6.1.4.1.5504.3.1.7.1.2 | ColumnzhoneSnmpErrorReqId | not-accessible | current | SNMP request ID of failed error. |
| 1.3.6.1.4.1.5504.3.1.7.1.3 | ColumnzhoneSnmpErrorDisplayString | read-write | current | The actual text string to show to the user. |
| 1.3.6.1.4.1.5504.3.1.7.1.4 | ColumnzhoneSnmpErrorTime | read-only | current | System time that the error occurred. This is used so the system will remove any old entries (older than 2 minutes) as it is unlikely that the cli or management… |
| 1.3.6.1.4.1.5504.3.1.8 | IdentityzhoneSoftwareDownload | current | Software Download information utilized by all Zhone devices in order to obtain software images on to local storage. In lower-end devices, the download itself m… | |
| 1.3.6.1.4.1.5504.3.1.8.1 | ScalarzhoneSysSwLogin | read-write | current | The login to be used on the remote system when downloading the image. This value is maintained throughout (i.e. persisted) and can be used for additional/futur… |
| 1.3.6.1.4.1.5504.3.1.8.2 | ScalarzhoneSysSwPassword | read-write | current | The password to be used on the remote system when downloading the image. This value is maintained throughout (i.e. persisted) and can be used for additional/fu… |
| 1.3.6.1.4.1.5504.3.1.8.3 | ScalarzhoneSysSwPriLoadServer | read-write | current | The IP address of the primary software load server. If the value of the zhoneSysSwPriLoadServer is set to 0.0.0.0 then no primary load server is available. If … |
| 1.3.6.1.4.1.5504.3.1.8.4 | ScalarzhoneSysSwSecLoadServer | read-write | current | The IP address of the secondary or back-up software load server, if there is no secondary server this should be set to 0.0.0.0 |
| 1.3.6.1.4.1.5504.3.1.8.5 | ScalarzhoneSysSwRemoteFilePath | read-write | current | The path on the remote system for the image to be loaded. |
| 1.3.6.1.4.1.5504.3.1.8.6 | ScalarzhoneSysSwLocalFilePath | read-write | current | The path on the system for the image to be stored. |
| 1.3.6.1.4.1.5504.3.1.8.7 | ScalarzhoneSysSwAdmin | read-write | current | (1) downloadSw: Download the image from the Primary load Server. If that fails, try to download from secondary load server. This value is only allowed if the z… |
| 1.3.6.1.4.1.5504.3.1.8.8 | ScalarzhoneSysSwStatus | read-only | current | (1) downLoadSwUnknown: No state known. This is the value if no sw download had been requested since the system was initialized or a delete command is in progre… |
| 1.3.6.1.4.1.5504.3.1.9 | IdentityzhoneSoftwareReboot | current | Reboot for system or particular type of cards. Common use is after software downloads but can be used anytime. Initiating a reboot requires admin access level … | |
| 1.3.6.1.4.1.5504.3.1.9.1 | ScalarzhoneSysRebootAdmin | read-write | current | systemReboot: reboot all the cards rebootByCardType : reboot all cards of a particular card Type (specified by zhoneSysRebootCardType). |
| 1.3.6.1.4.1.5504.3.1.9.2 | ScalarzhoneSysRebootCardType | read-write | current | The numerical representation of what unit/card type has to be rebooted. |
| 1.3.6.1.4.1.5504.3.1.10 | TablezhoneSysCardSoftwareConfigTable | not-accessible | current | The software configuration for this card. For every card (i.e. shelf/slot) in the system, an entry must be created in order for the card to get loaded with sof… |
| 1.3.6.1.4.1.5504.3.1.10.1 | RowzhoneSysCardSoftwareConfigEntry | not-accessible | current | An entry for a particular card. An entry is added by the manager in order for a card to be available for loading. If an entry does not exist for a card, no loa… |
| 1.3.6.1.4.1.5504.3.1.10.1.1 | ColumnzhoneSysCardSpecificSwFileName | read-create | current | The file or code image name of the specific software version that should be loaded by the unit/card for operation. If a failure occurs when trying to boot an u… |
| 1.3.6.1.4.1.5504.3.1.10.1.2 | ColumnzhoneSysCardSwSpecificVers | read-only | current | The software version of the file name specified in zhoneSysCardSpecificSwFileName. If the revision is not known or the file name is NULL, this should return an… |
| 1.3.6.1.4.1.5504.3.1.10.1.3 | ColumnzhoneSysCardUpgradeSwFileName | read-create | current | The file name of the software version that should be loaded by the unit/card into the upgrade region of the card/unit memory or storage. This file takes precen… |
| 1.3.6.1.4.1.5504.3.1.10.1.4 | ColumnzhoneSysCardSwUpgradeVers | read-only | current | The software version specified in the zhoneSysCardUpgrade FileName variable in this table that will be loaded on the next card reboot. This object complies to … |
| 1.3.6.1.4.1.5504.3.1.10.1.5 | ColumnzhoneSysCardSwType | read-create | current | The card type for the card in this shelf/slot. When initially created, this value is defaulted to 'unknown'. When the card requests a load, the value in this f… |
| 1.3.6.1.4.1.5504.3.1.10.1.6 | ColumnzhoneSysCardSwEnable | read-create | current | Whether or not the card has been enabled to be loaded. If this value is false, no sw will be loaded, otherwise the logic flow defined in the table description … |
| 1.3.6.1.4.1.5504.3.1.10.1.7 | ColumnzhoneSysCardSwUpgradeEnable | read-create | current | This field indicates whether the zhoneSysCardUpgradeSwFileName should be used as the software image when the card requests a software load. This value can eith… |
| 1.3.6.1.4.1.5504.3.1.10.1.8 | ColumnzhoneSysCardRowStatus | read-create | current | The row status used to create or delete an entry for a card (i.e. shelf/slot). No entries are required to be included in a table create as all entries have def… |
| 1.3.6.1.4.1.5504.3.1.10.1.9 | ColumnzhoneSysCardLineType | read-create | current | This field is used to identify which line types for different cards For normal e1/t1 cards only t1 and e1 (uni mode) line types are supported. For MALC t1Ima U… |
| 1.3.6.1.4.1.5504.3.1.10.1.10 | ColumnzhoneSysCardAtmConfiguration | read-create | current | This field specifies how internal resources are distributed between aal5 resources and aal2/cell relay resources based on the core use of this card. This field… |
| 1.3.6.1.4.1.5504.3.1.10.1.11 | ColumnzhoneSysCardLineVoltage | read-create | current | Sepcifies the voltage supplied to all lines (ports) of this card, Used on ISDN line cards. |
| 1.3.6.1.4.1.5504.3.1.10.1.12 | ColumnzhoneSysCardVpiVciRange | read-create | current | The maximum vpi and vci values that may be used for this card. |
| 1.3.6.1.4.1.5504.3.1.10.1.13 | ColumnzhoneSysCardInitString | read-create | current | Ascii string containing tokens separated by ',' or ' ' which is used to configure special non-standard operations. This string is blank for normal operation. |
| 1.3.6.1.4.1.5504.3.1.10.1.14 | ColumnzhoneSysCardWettingCurrent | read-create | current | Sepcifies weather wetting current is disabled or enabled(standard). |
| 1.3.6.1.4.1.5504.3.1.11 | NodezhoneCardRedundancy | |||
| 1.3.6.1.4.1.5504.3.1.11.1 | ScalarnextCardRedundancyGroupId | read-only | current | Returns the next unused card Redundancy Group Id. |
| 1.3.6.1.4.1.5504.3.1.11.2 | TablezhoneSysCardRedundancyTable | not-accessible | current | This table is used to group redundant cards and provide a mechanism to indicate which card, if any, is preferred to be active. A weight is assigned to each car… |
| 1.3.6.1.4.1.5504.3.1.11.2.1 | RowzhoneSysCardRedundancyEntry | not-accessible | current | An entry for a particular card. |
| 1.3.6.1.4.1.5504.3.1.11.2.1.1 | ColumnzhoneSysCardRedundancyGroupId | accessible-for-notify | current | The unique redundancy group to which the card is assigned. |
| 1.3.6.1.4.1.5504.3.1.11.2.1.2 | ColumnzhoneSysCardRedundancyWeight | read-create | current | A weight given to this card in determining whether this card should become Active on system boot. |
| 1.3.6.1.4.1.5504.3.1.11.2.1.3 | ColumnzhoneSysCardRedundancyHoldActive | read-create | current | When set to true, this indicates that the card, when Active, should remain in the Active state regardless of any system events. This effectively disables redun… |
| 1.3.6.1.4.1.5504.3.1.11.2.1.4 | ColumnzhoneSysCardRedundancyOperStatus | read-only | current | Indicates the status of the card. Note that a noStatus value means that the card is in a non-operational state, such as booting or fault. |
| 1.3.6.1.4.1.5504.3.1.11.2.1.5 | ColumnzhoneSysCardRedundancyRowStatus | read-create | current | The row status used to create or delete an entry for card redundancy. No entries are required to be included in a table create as all entries have default sett… |
| 1.3.6.1.4.1.5504.3.1.12 | IdentityzhoneSntpConfiguration | current | Configuration of parameters for SNTP. The SLMS node will act as an SNTP Client and synchronize the time and date from the network as specified in this table. T… | |
| 1.3.6.1.4.1.5504.3.1.12.1 | ScalarzhoneSntpPrimaryServerIpAddr | read-write | current | The IP address of the Primary NTP Server from which the date/time will be synchronized. |
| 1.3.6.1.4.1.5504.3.1.12.2 | ScalarzhoneSntpSecondaryServerIpAddr | read-write | current | The IP address of the Secondary NTP Server from which the date/time will be synchronized. Whenever the Primary NTP Server is not available, the Secondary NTP S… |
| 1.3.6.1.4.1.5504.3.1.12.3 | ScalarzhoneSntpLocalTimeZone | read-write | current | Indicates the local time zone. |
| 1.3.6.1.4.1.5504.3.1.12.4 | ScalarzhoneSntpDaylightSavingTime | read-write | current | Indicates whether Daylight Savings time is currently in affect. |
| 1.3.6.1.4.1.5504.3.1.12.5 | ScalarzhoneSntpDaylightSavingStart | read-write | current | Indicates the daylight savings start time. The start time should be of the format mm:dd:hh:mm |
| 1.3.6.1.4.1.5504.3.1.12.6 | ScalarzhoneSntpDaylightSavingEnd | read-write | current | Indicates the daylight savings end time. The start time should be of the fo rmat mm:dd:hh:mm |
| 1.3.6.1.4.1.5504.3.1.13 | IdentityzhoneAdslPotsBypassRelay | current | The objects contained in this ojbect identity are scalar objects used for provisioning and viewing the Adsl Pots LPF Bypass Relays. | |
| 1.3.6.1.4.1.5504.3.1.13.1 | ScalarzhoneAdslPotsMaxActiveBypassRelays | read-only | current | Maximum number of Adsl Pots LPF Bypass Relays that can be active on any one card at any given time. This number is determined by the device and is calculated b… |
| 1.3.6.1.4.1.5504.3.1.13.2 | ScalarzhoneAdslPotsBypassRelayResetAll | read-write | current | Enables the operator to force all Pots Bypass Relays in the system back to a normal state. This object is only valid for Adsl Pots Splitter cards containing th… |
| 1.3.6.1.4.1.5504.3.1.14 | IdentityzhoneBulkStatsSystemConfiguration | current | System wide configuration of bulk statistics, including ftp parameters and enabling/disabling bulk statistics collection for the system. | |
| 1.3.6.1.4.1.5504.3.1.14.1 | ScalarzhoneBulkStatsSystemCollectionEnabled | read-write | current | Indicates whether bulk stats collection has been enabled for the system. If false, no collection is done. If true, the system will collect the stats identified… |
| 1.3.6.1.4.1.5504.3.1.14.2 | ScalarzhoneBulkStatsSystemFtpAddress | read-write | current | The IP address of the FTP Server to which the collected stats will be sent. |
| 1.3.6.1.4.1.5504.3.1.14.3 | ScalarzhoneBulkStatsSystemFtpLogin | read-write | current | The FTP login name to be used for initiating the FTP file transfer of the collected bulk statistics. |
| 1.3.6.1.4.1.5504.3.1.14.4 | ScalarzhoneBulkStatsSystemFtpPassword | read-write | current | The FTP password to be used for initiating the FTP file transfer of the collected bulk statistics. |
| 1.3.6.1.4.1.5504.3.1.14.5 | ScalarzhoneBulkStatsSystemFtpDirPath | read-write | current | This specifies the directory path on the FTP server into which the bulk statistics files will be transferred. The device will use this in a cd command, therefo… |
| 1.3.6.1.4.1.5504.3.1.14.6 | ScalarzhoneBulkStatsSystemOperStatus | read-only | current | The operational status of the current collection interval. Valid values are: collectionInProgress: - Collection for the current interval has started collection… |
| 1.3.6.1.4.1.5504.3.1.15 | NodezhoneBulkStatCollection | |||
| 1.3.6.1.4.1.5504.3.1.15.1 | ScalarnextBulkStatCollectionId | read-only | current | Returns the next unused bulk statistics collection id. |
| 1.3.6.1.4.1.5504.3.1.15.2 | TablezhoneBulkStatCollectionTable | not-accessible | current | This table is used to identify the statistics to be collected in bulk. Each row in the table represents a statistic to be collected. |
| 1.3.6.1.4.1.5504.3.1.15.2.1 | RowzhoneBulkStatCollectionEntry | not-accessible | current | Defines an entry in the zhoneBulkStatCollectionTable. |
| 1.3.6.1.4.1.5504.3.1.15.2.1.1 | ColumnzhoneBulkStatCollectionId | not-accessible | current | Unique identifier of the bulk statistic row. |
| 1.3.6.1.4.1.5504.3.1.15.2.1.2 | ColumnzhoneBulkStatEnabled | read-create | current | Indicate whether collection in enabled for this statistic. |
| 1.3.6.1.4.1.5504.3.1.15.2.1.3 | ColumnzhoneBulkStatOID | read-create | current | The OID of the statistic to be collected in bulk. |
| 1.3.6.1.4.1.5504.3.1.15.2.1.4 | ColumnzhoneBulkStatInstance | read-write | current | The Instance value for the zhoneBulkStatOID. |
| 1.3.6.1.4.1.5504.3.1.15.2.1.5 | ColumnzhoneBulkStatIncludeChildren | read-create | current | Indicates whether the statistic collection should include children. Using the zhoneAtmStatsExtTable (presently with 8 statistics in the table) as example, one … |
| 1.3.6.1.4.1.5504.3.1.15.2.1.6 | ColumnzhoneBulkStatsCollectionInterval | read-create | current | The collection interval for this statistic. Initially, all statistics will be collected on 15 minute intervals, and sets to this object are not supported. |
| 1.3.6.1.4.1.5504.3.1.15.2.1.7 | ColumnzhoneBulkStatCollectionRowStatus | read-create | current | The row status is used to create or delete an entry in this table. |
| 1.3.6.1.4.1.5504.3.1.16 | IdentityzhoneVideoSystemConfiguration | current | Configuration information for the MALC video Head-End Server configuration. Managing the Head-End configuration requires provisioning the MALC with IP informat… | |
| 1.3.6.1.4.1.5504.3.1.16.1 | ScalarzhoneVideoSystemConfigurationIndexNext | read-only | current | This object contains an appropriate value to be used for zhoneVideoSystemConfigurationIndex when creating entries in the zhoneVideoSystemConfigurationTable. Th… |
| 1.3.6.1.4.1.5504.3.1.16.2 | TablezhoneVideoSystemConfigurationTable | not-accessible | current | This table is used to identify and manage the Head-End Video Servers. Each row in the table represents a Head-End Server. |
| 1.3.6.1.4.1.5504.3.1.16.2.1 | RowzhoneVideoSystemConfigurationEntry | not-accessible | current | Defines an entry in the Video System Configuration table. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.1 | ColumnzhoneVideoSystemConfigurationIndex | not-accessible | current | A unique value to identify this video system profile entry. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.2 | ColumnzhoneVideoSystemConfigurationNtpServerAddress | read-create | current | This oid contains the IP address of the NTP Server for a particular Head-End. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.3 | ColumnzhoneVideoSystemConfigurationEpgServerAddress | read-create | current | This oid contains the IP adress of the EPG (Electronic Programming Guide) for a particular Head-End. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.4 | ColumnzhoneVideoSystemConfigurationSettopBoxHeadEndServerAddress | read-create | current | This oid contains the IP address of the set-top box head-end server. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.5 | ColumnzhoneVideoSystemConfigurationDefaultChannelAddress | read-create | current | his oid contains the multicast IP address of the channel chosen to be the default channel for a particular head- end provider. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.6 | ColumnzhoneVideoSystemConfigurationNoChannelAvailableAddress | read-create | current | This oid contains the multicast address of the channel appropriate to display when a user selects a channel that is not available or not in his channel profile. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.7 | ColumnzhoneVideoSystemConfigurationRowStatus | read-create | current | zhoneVideoSystemConfigurationRowStatus is used to create/delete an entry in the zhoneVideoSystemConfigurationTable. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.8 | ColumnzhoneVideoSystemConfigurationEpgType | read-write | current | Indicates the type of EPG that we are talking to. Currently only Minerva, and Myrio are envisioned. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.9 | ColumnzhoneVideoSystemConfigurationEpgPort | read-write | current | This oid contains the port number to use when talking with the EPG. |
| 1.3.6.1.4.1.5504.3.1.16.2.1.10 | ColumnzhoneVideoSystemConfigurationEpgFtpAddress | read-write | current | This oid is the IP address to use when FTP data to/from the EPP server. |
| 1.3.6.1.4.1.5504.3.1.17 | IdentityzhoneCallDetailRecConfig | current | System wide configuration of the Call Detail Recording. | |
| 1.3.6.1.4.1.5504.3.1.17.1 | ScalarzhoneCallDetailRecEnabled | read-write | current | Indicates whether CDR is enabled for this device. If false, the CDR is disabled. If true, the CDR is enabled, each call is recorded and a report is sent period… |
| 1.3.6.1.4.1.5504.3.1.17.2 | ScalarzhoneCallDetailRecFlushLog | read-write | current | If true, indicates the device to upload all pending call records and empty the CDR log. After the uploading is completed the flag is automatically set to false… |
| 1.3.6.1.4.1.5504.3.1.17.3 | ScalarzhoneCallDetailRecCurrFtpServer | read-only | current | Currently active FTP server. In case all FTP servers are not available the none(3) value is assigned. |
| 1.3.6.1.4.1.5504.3.1.17.4 | ScalarzhoneCallDetailRecPrimFtpIpAddr | read-write | current | IP address of the primary FTP server. If configured and available, it becomes the most preferable FTP server. |
| 1.3.6.1.4.1.5504.3.1.17.5 | ScalarzhoneCallDetailRecSecFtpIpAddr | read-write | current | IP address of the secondary FTP server. This server is automatically selected when the primary FTP server is not configured or unavailable. The device will pro… |
| 1.3.6.1.4.1.5504.3.1.17.6 | ScalarzhoneCallDetailRecFtpLogin | read-write | current | The FTP login name to be used by the device for initiating the transfer. |
| 1.3.6.1.4.1.5504.3.1.17.7 | ScalarzhoneCallDetailRecFtpPassword | read-write | current | The FTP password to be used by the device during login to the FTP server. |
| 1.3.6.1.4.1.5504.3.1.17.8 | ScalarzhoneCallDetailRecFtpDirPath | read-write | current | The directory path on the FTP server where a file with CDR records is to be stored. The trailing '/' is not required. Within this directory, each device will h… |
| 1.3.6.1.4.1.5504.3.1.17.9 | ScalarzhoneCallDetailRecRepPeriod | read-write | current | This specifies the device reporting period in minutes. During this period a device is collecting CDR records and when this period elapses it triggers automatic… |
| 1.3.6.1.4.1.5504.3.1.17.10 | ScalarzhoneCallDetailRecOperStatus | read-only | current | CDR Operational Status: active - CDR is enabled and working OK. ftpFailure - CDR cannot upload log due to lack of available FTP server. overrun - In result of … |
| 1.3.6.1.4.1.5504.3.1.19 | IdentityzhoneSoftwareUpgrade | current | Used to upgrade device software during hitless upgrade. | |
| 1.3.6.1.4.1.5504.3.1.19.1 | ScalarzhoneSoftwareUpgradeAction | read-write | current | Describes which software upgrade action to perform. |
| 1.3.6.1.4.1.5504.3.1.19.2 | ScalarzhoneSoftwareUpgradeStatus | read-only | current | Describes status of software upgrade. |
| 1.3.6.1.4.1.5504.3.1.19.3 | ScalarzhoneSoftwareUpgradeTimeStarted | read-only | current | Time software upgrade started. |
| 1.3.6.1.4.1.5504.3.1.19.4 | ScalarzhoneSoftwareUpgradeTimeCompleted | read-only | current | Time software upgrade completed. |
| 1.3.6.1.4.1.5504.3.1.20 | IdentityzhoneFileSystem | current | Represents SNMP view of Zhone File System available from Zhone Command Line Interface. | |
| 1.3.6.1.4.1.5504.3.1.20.1 | ScalarzhoneFileAction | read-write | current | File Action: cd(1) - change directory command used in conjunction with zhoneDirectory location which specifies destination directory. dir(2) - listing of files… |
| 1.3.6.1.4.1.5504.3.1.20.2 | ScalarzhoneFileName1 | read-write | current | Used when zhoneFileAction set to 'copy'. This will be the source filename of the file to be copied. Prepend a new path if you want to specify a file in a direc… |
| 1.3.6.1.4.1.5504.3.1.20.3 | ScalarzhoneFileName2 | read-write | current | Used when zhoneFileAction set to 'copy'. This will be the resulting filename of the copied file. Prepend a new path if you want file to be written to a differe… |
| 1.3.6.1.4.1.5504.3.1.20.4 | ScalarzhoneDirectoryPath | read-write | current | This is a read-write object. If read, it returns your current directory location. If written, it can be used by the 'cd' change directory command in order to s… |
| 1.3.6.1.4.1.5504.3.1.20.5 | ScalarzhoneDirectoryBytesAvailable | read-only | current | Total number of bytes available on the disk. |
| 1.3.6.1.4.1.5504.3.1.20.6 | ScalarzhoneBytesReservedForProvisioning | read-only | current | When in the 'datastor' directory, this object returns the number of bytes reserved for Zhone Provisioning. These are the number of bytes reserved for the datab… |
| 1.3.6.1.4.1.5504.3.1.20.7 | TablezhoneFileTable | not-accessible | current | Zhone File Listing Table. Used to view file information for files resident on Zhone Flash Memory Devices. |
| 1.3.6.1.4.1.5504.3.1.20.7.1 | RowzhoneFileEntry | not-accessible | current | Zhone File Listing Entry. Used to view file information for files resident on Zhone Flash Memory Devices. |
| 1.3.6.1.4.1.5504.3.1.20.7.1.1 | ColumnzhoneFileIndex | not-accessible | current | Index values of rows in this table. Positive ascending numbers starting at 1. |
| 1.3.6.1.4.1.5504.3.1.20.7.1.2 | ColumnzhoneFileDirectoryPath | read-only | current | Directory path of file. |
| 1.3.6.1.4.1.5504.3.1.20.7.1.3 | ColumnzhoneFileName | read-only | current | Filename. |
| 1.3.6.1.4.1.5504.3.1.20.7.1.4 | ColumnzhoneFilePrivilege | read-only | current | File privileges. |
| 1.3.6.1.4.1.5504.3.1.20.7.1.5 | ColumnzhoneFileSize | read-only | current | File size in bytes. |
| 1.3.6.1.4.1.5504.3.1.20.7.1.6 | ColumnzhoneFileLastModified | read-only | current | Date and time file last modified. |
| 1.3.6.1.4.1.5504.3.1.21 | IdentitycpeMgr | current | Access, control and runtime details for managing CPEs connected to Zhone CO devices. Some of these objects will reside on CO devices, while others will reside … | |
| 1.3.6.1.4.1.5504.3.1.22 | IdentityzhoneEnhancedStatus | current | Object Identity for Zhone Enhanced Status. | |
| 1.3.6.1.4.1.5504.3.1.22.1 | TablezhoneEnhancedStatusTable | not-accessible | current | Table of Zhone Enhanced Status codes which are used to extend the current IETF definitions found in snmpdef.h. These status codes and corresponding text can be… |
| 1.3.6.1.4.1.5504.3.1.22.1.1 | RowzhoneEnhancedStatusEntry | not-accessible | current | Row in the table. |
| 1.3.6.1.4.1.5504.3.1.22.1.1.1 | ColumnzhoneEnhancedStatusIndex | not-accessible | current | Entry index value. |
| 1.3.6.1.4.1.5504.3.1.22.1.1.2 | ColumnzhoneEnhancedStatusCode | read-only | current | Status code returned in SNMP packet as a result of issuing getproc_error, nextproc_error, testproc_error or setproc_error. Also used for reporting CLI errors. |
| 1.3.6.1.4.1.5504.3.1.22.1.1.3 | ColumnzhoneEnhancedStatusText | read-only | current | Given the zhoneEnhancedStatusCode, this is the corresponding text to be displayed to user in either SNMP or CLI. |
| 1.3.6.1.4.1.5504.3.8.1 | IdentityzhoneTrapCpePoll | current | This is the Trap information related to the Zhone CPE polling task which exists on the BAN. This task polls all connected Zhone CPE devices by sending SNMP Set… | |
| 1.3.6.1.4.1.5504.3.8.1.0 | IdentityzhoneTrapCpePollV2Traps | current | This object identity adds a zero(0) for the next to last sub-identifier which should be used for new SNMPv2 Traps. | |
| 1.3.6.1.4.1.5504.3.8.1.0.1 | NotificationzhoneTrapCpeConnectionDown | current | A Zhone CPE connection in down. The Trap objects specify the location of the Zhone CPE device. | |
| 1.3.6.1.4.1.5504.3.8.1.0.2 | NotificationzhoneTrapCpeConnectionUp | current | A Zhone CPE connection that has previously been down is now up. The Trap objects specify the location of the Zhone CPE device. | |
| 1.3.6.1.4.1.5504.3.8.2 | IdentityzhoneTrapConfigSync | current | The trap sent when an object in the device datastore is changed | |
| 1.3.6.1.4.1.5504.3.8.2.0 | IdentityzhoneTrapConfigSyncV2Traps | current | This object identity adds a zero(0) for the next to last sub-identifier which should be used for new SNMPv2 Traps. | |
| 1.3.6.1.4.1.5504.3.8.2.0.1 | NotificationzhoneTrapConfigSyncChange | current | An object in the device datastore has changed | |
| 1.3.6.1.4.1.5504.3.8.2.0.2 | NotificationzhoneTrapConfigSyncReset | current | ConfigSync has timed-out on the device and has subsequently been reset to a nominal state by the device. Resetting configsync on the device consists of closing… | |
| 1.3.6.1.4.1.5504.3.8.4 | IdentityzhoneTrapSnmp | current | These are traps generated by SNMP, itself, when an error condition is detected. | |
| 1.3.6.1.4.1.5504.3.8.4.0 | IdentityzhoneTrapSnmpV2Traps | current | This object identity adds a zero(0) for the next to last sub-identifier which should be used for new SNMPv2 Traps. | |
| 1.3.6.1.4.1.5504.3.8.4.0.1 | NotificationzhoneTrapSnmpSATimeout | current | Trap occurs when an error condition is detected in sub agent, causing the Zhone SNMP Master agent to timeout. Shelf and slot in the trap will refer to the suba… | |
| 1.3.6.1.4.1.5504.3.8.5 | IdentityzhoneTrapCardRedundancy | current | Card Redundancy Traps | |
| 1.3.6.1.4.1.5504.3.8.5.0 | IdentityzhoneCardRedundancyV2Traps | current | This object identity adds a zero(0) for the next to last sub-identifier which should be used for new SNMPv2 Traps. | |
| 1.3.6.1.4.1.5504.3.8.5.0.1 | NotificationzhoneCardRedundancyStatusChange | current | Trap indicates that the specified card has become active. | |
| 1.3.6.1.4.1.5504.3.8.5.0.2 | NotificationzhoneCardRedundancyUnsafe | current | Trap if system is provisioned for redundant uplinks but is not redundancy ready. | |
| 1.3.6.1.4.1.5504.3.8.6 | IdentityzhoneTrapBulkStatistics | current | Bulk Statistics Traps. | |
| 1.3.6.1.4.1.5504.3.8.6.0 | IdentityzhoneBulkStatisticsV2Traps | current | This object identity adds a zero(0) for the next to last sub-identifier which should be used for new SNMPv2 Traps. | |
| 1.3.6.1.4.1.5504.3.8.6.0.1 | NotificationzhoneBulkStatisticsIntervalFailure | current | This notification alerts the manager that the device could not successfully complete the current collection interval. The zhoneBulkStatsSystemOperStatus is inc… | |
| 1.3.6.1.4.1.5504.3.8.7 | IdentityzhoneTrapZms | current | Object identifier under which Zhone ZMS related traps are defined. | |
| 1.3.6.1.4.1.5504.3.8.7.0 | IdentityzhoneTrapZmsV2Traps | current | The SNMPv2 zero(0) prefix for Zhone ZMS traps. | |
| 1.3.6.1.4.1.5504.3.8.7.0.1 | NotificationzhoneZmsBlockCliChange | deprecated | This is trap is generated when the value of zhoneZmsBlockCli is changed. | |
| 1.3.6.1.4.1.5504.6.2 | IdentityzhoneSystemModule | This module contains the system generic variables that are complete for the entire system. Note that some functional entities are maintained in their own mib a… | ||
| 1.3.6.1.4.1.5504.8 | NodezhoneCompliances | |||
| 1.3.6.1.4.1.5504.8.1 | NodezhoneGroups | |||
| 1.3.6.1.4.1.5504.8.1.1 | GroupzhoneSystemGroup | current | Description. | |
| 1.3.6.1.4.1.5504.8.1.2 | GroupzhoneDeprecatedSystemGroup | deprecated | Description. | |
| 1.3.6.1.4.1.5504.8.1.3 | GroupzhoneTrapGroup | current | Description. | |
| 1.3.6.1.4.1.5504.8.1.4 | GroupzhoneDeprecatedTrapGroup | deprecated | Description. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| ZhoneLocalTimeZone | INTEGER { internationalDateLineWest(1), nome(2), hawaii(3), yukon(4), pacific(5), mountain(6), central(7), eastern(8), atlantic(9), newfoundland(10), brasilia(11), azores(12), westAfrica(13), gmt(14), centralEuropean(15), easternEurope(16), baghdad(17), tehran(18), uae(19), afghanistan(20), islamabad(21), india(22), kathmandu(23), dhaka(24), rangoon(25), bangkok(26), chinaCoast(27), japan(28), australia(29), guam(30), magadan(31), newZealand(32), rawakiIslands(33), lineIslands(34) } zhoneZms OBJECT-IDENTITY STATUS current DESCRIPTION "The following variables are associated with the state of existence and connectivity with the Zhone Management System (ZMS)." ::= { zhoneSystem 1 } | current | World time zones: internationalDateLineWest (GMT-12:00 hrs) nome (GMT-11:00) hawaii(GMT-10:00) yukon(GMT-9:00) pacific(GMT-8:00) mountain(GMT-7:00) central(GMT-6:00) eastern(GMT-5:00) atlantic(GMT-4:00) newfoundland(GMT… |
| ZhoneRedundancyWeight | INTEGER { neverActive(1), noPreference(2), slightPreference(3), mediumPreference(4), highPreference(5) } | current | Preference values for redundancy |