CISCO-ATM-CONN-MIB
176 objects
This MIB module is a cisco extension to VPL/VCL table defined in rfc1695 for ATM switch connection management.
Imported Objects
| ATM-MIB | AtmTrafficDescrParamIndex atmVclVci atmVclVpi atmVplVpi |
| CISCO-ATM-IF-MIB | NsapAtmAddr |
| CISCO-ATM-RM-MIB | LsPerVcqThresholdGroup |
| CISCO-SMI | ciscoExperiment |
| IF-MIB | ifIndex InterfaceIndexOrZero |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.13 | IdentityciscoAtmConnMIB | This MIB module is a cisco extension to VPL/VCL table defined in rfc1695 for ATM switch connection management. | ||
| 1.3.6.1.4.1.9.10.13.1 | NodeciscoAtmConnMIBObjects | |||
| 1.3.6.1.4.1.9.10.13.1.1 | NodeciscoAtmVpl | |||
| 1.3.6.1.4.1.9.10.13.1.1.1 | TableciscoAtmVplTable | not-accessible | current | The Virtual Path Link extension Table. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1 | RowciscoAtmVplEntry | not-accessible | current | An entry in the Vpl table.This entry is used to model a bi-directional Vpl. This table augments the atmVplTable defined in RFC 1695. However it uses ifIndex an… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.1 | ColumnciscoAtmVplCastType | read-write | current | Vpl type is either a point to point connection or point to multipoint root or leaf. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.2 | ColumnciscoAtmVplSpanType | read-only | current | Vpl span is either a transit one or a terminating one. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.3 | ColumnciscoAtmVplConfigType | read-write | current | Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.4 | ColumnciscoAtmVplRxUpcMode | read-write | current | Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.5 | ColumnciscoAtmVplConnState | read-write | current | The connection state of this VPL. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.6 | ColumnciscoAtmVplOamLoopbkTxInterval | read-write | current | Frequency of OAM loopback cells generated. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.7 | ColumnciscoAtmVplOamSegmentLoopback | read-write | current | Enable segment loopback on this virtual path. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.8 | ColumnciscoAtmVplOamEndLoopback | read-write | current | Enable end to end loopback on this virtual path. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.9 | ColumnciscoAtmVplOamAisEnable | read-write | current | Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual path. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.10 | ColumnciscoAtmVplOamRdiEnable | read-write | current | Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.11 | ColumnciscoAtmVplInstallTime | read-only | current | The time stamp derived from sysUpTime when this VPL gets created. The VPL entries are created/deleted as a by-product of creating and deleting entries in the a… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.12 | ColumnciscoAtmVplInCells | read-only | current | The total number of cells received on this VPL. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.13 | ColumnciscoAtmVplOutCells | read-only | current | The total number of cells transmitted on this VPL. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.14 | ColumnciscoAtmVplCrossIfIndex | read-write | current | For point to point, this is the cross-connected VPL's ifIndex of this VPL. For point to multi-point connection, this will be the root VPL's ifIndex for a leaf … |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.15 | ColumnciscoAtmVplCrossVpi | read-write | current | This specifies the VPI value of the VPL to which this VPL is cross-connected. For point to multi-point connection, this is the root VPL's VPI for the leaf entr… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.16 | ColumnciscoAtmVplNextLeafIfIndex | read-only | current | For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VPL's ifIndex on the multicast chain. This will… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.17 | ColumnciscoAtmVplNextLeafVpi | read-only | current | For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VPL's VPI on the multicast chain. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.18 | ColumnciscoAtmVplRemoteAddr | read-write | current | Soft PVP target address if this is the calling side Soft PVP source address if this is called side. Atomically set ConnState, RemoteAddr and RemoteVpi will cre… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.19 | ColumnciscoAtmVplRemoteVpi | read-write | current | Soft PVP target VPI in calling side. 0 in called side. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.20 | ColumnciscoAtmVplLocation | read-only | current | Indicate calling or called side of a soft PVP. If ciscoAtmVplConfigType is not soft then ciscoAtmVplLocation value should be ignored. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.21 | ColumnciscoAtmVplSlowRetryIntv | read-write | current | Soft PVP slow retry interval time in seconds. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.22 | ColumnciscoAtmVplNumAttempts | read-only | current | Number of retries made to install this soft PVP connection. If ciscoAtmVplConfigType is not soft then ciscoAtmVplNumAttempts value should be ignored. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.23 | ColumnciscoAtmVplLastReleaseCause | read-only | current | Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVP. Indicates the reason for the Release. … |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.24 | ColumnciscoAtmVplLogicalPortDef | read-write | current | Indicates whether the VPC at this VPL interface is an Atm Logical Port interface. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.25 | ColumnciscoAtmVplLogicalPortIndex | read-only | current | The ifTable index of the Atm logical port interface associated with this VPL. Only valid if the value of atmVplLogicalPortDef is isLogicalIf, and the VPL row i… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.26 | ColumnciscoAtmVplUpcViolations | read-only | current | The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VPL. On LS1010 systems, this counter is valid only… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.27 | ColumnciscoAtmVplEpdTpdCellDrops | read-only | obsolete | Never implemented. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.28 | ColumnciscoAtmVplEpdTpdPacketDrops | read-only | obsolete | Never implemented. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.29 | ColumnciscoAtmVplEpdTpdPacketsIn | read-only | obsolete | Never implemented. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.30 | ColumnciscoAtmVplClp1Drops | read-only | obsolete | Never implemented. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.31 | ColumnciscoAtmVplDefaultRxUpcTolerance | read-only | current | If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified … |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.32 | ColumnciscoAtmVplDefaultRxUpcVbrCdvt | read-only | current | If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VPL creation, this objec… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.33 | ColumnciscoAtmVplLsPerVcqWrrWeight | read-write | current | Configure the weighting specified for a VP half-leg within a service class to make the scheduling decision among other active VPLs in the service class. This i… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.34 | ColumnciscoAtmVplLsPerVcqTunnelIsShaped | read-write | current | Determines whether this is to be a -shaped- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a shaped VP Tunnel… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.35 | ColumnciscoAtmVplLsPerVcqXmtQueuedCells | read-only | current | Number of cells received on this VPL and residing on the per-connection queue. Note that this value is not valid until the VPL is in an active cross-connect. T… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.36 | ColumnciscoAtmVplLsPerVcQThreshGrp | read-only | current | The Threshold Group to which the cell-queue for cells received by this VP are queued. This object is defined only when the switch is equipped with the Lightstr… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.37 | ColumnciscoAtmVplInClp0Cells | read-only | current | The total number of cells with the CLP bit clear received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if th… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.38 | ColumnciscoAtmVplInClp1Cells | read-only | current | The total number of cells with the CLP bit set received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the … |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.39 | ColumnciscoAtmVplOutClp0Cells | read-only | current | The total number of cells with the CLP bit clear transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.40 | ColumnciscoAtmVplOutClp1Cells | read-only | current | The total number of cells with the CLP bit set transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS10… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.41 | ColumnciscoAtmVplCellDrops | read-only | current | The total number of cells received on this VPL, but discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 system… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.43 | ColumnciscoAtmVplClp0VcqFullCellDrops | read-only | current | The total number of cells received on this VPL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if t… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.44 | ColumnciscoAtmVplVcqClpThreshCellDrops | read-only | current | The total number of cells received on this VPL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and th… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.45 | ColumnciscoAtmVplLsPerVcqTunnelIsHierarchical | read-write | current | Determines whether this is to be a -Hierarchical- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a Hierarchic… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.46 | ColumnciscoAtmVplRxNegTraffDescrIndex | read-only | current | Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VPL. This object is… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.47 | ColumnciscoAtmVplTxNegTraffDescrIndex | read-only | current | Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VPL. This object i… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.48 | ColumnciscoAtmVplSwFabOutCells | read-only | current | The total number of cells transmitted on this VPL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.49 | ColumnciscoAtmVplSwFabOutClp0Cells | read-only | current | The total number of cells with the CLP bit clear transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical inte… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.50 | ColumnciscoAtmVplSwFabOutClp1Cells | read-only | current | The total number of cells with the CLP bit set transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interf… |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.51 | ColumnciscoAtmVplConnName | read-write | current | A human readable string that identifies this connection. This object will return a zero-length string if value is not set. |
| 1.3.6.1.4.1.9.10.13.1.1.1.1.52 | ColumnciscoAtmVplConnType | read-write | current | This object represent the PVP Type for this connection. - local connection within the node - endToEnd across several nodes This object serves as an information… |
| 1.3.6.1.4.1.9.10.13.1.2 | NodeciscoAtmVcl | |||
| 1.3.6.1.4.1.9.10.13.1.2.1 | TableciscoAtmVclTable | not-accessible | current | The Virtual Channel Link extension Table. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1 | RowciscoAtmVclEntry | not-accessible | current | An entry in the Vcl table.This entry is used to model a bi-directional Vcl. This table augments the atmVclTable defined in RFC 1695. However it uses ifIndex, a… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.1 | ColumnciscoAtmVclCastType | read-write | current | Vcl type is either a point to point connection or point to multipoint root or leaf. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.2 | ColumnciscoAtmVclSpanType | read-only | current | Vcl span is either a transit one or a terminating one. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.3 | ColumnciscoAtmVclConfigType | read-write | current | Vcl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.4 | ColumnciscoAtmVclRxUpcMode | read-write | current | Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.5 | ColumnciscoAtmVclEpdEnable | read-write | current | Early Packet Discard option used for this VCL. The use is as follows: enable(1) Packet-discard is enabled. disable(2) Packet-discard is disabled. useTrafficDes… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.6 | ColumnciscoAtmVclConnState | read-write | current | The connection state of this VCL. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.7 | ColumnciscoAtmVclOamLoopbkTxInterval | read-write | current | Frequency of OAM loopback cell are generated on this virtual channel. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.8 | ColumnciscoAtmVclOamSegmentLoopback | read-write | current | Enable segment loopback on this virtual channel. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.9 | ColumnciscoAtmVclOamEndLoopback | read-write | current | Enable end to end loopback on this virtual channel. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.10 | ColumnciscoAtmVclOamAisEnable | read-write | current | Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual channel. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.11 | ColumnciscoAtmVclOamRdiEnable | read-write | current | Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.12 | ColumnciscoAtmVclInstallTime | read-only | current | The time stamp derived from sysUpTime when this VCL gets created. The VCL entries are created/deleted as a by-product of creating and deleting entries in the a… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.13 | ColumnciscoAtmVclInCells | read-only | current | The total number of cells received on this VCL. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.14 | ColumnciscoAtmVclOutCells | read-only | current | The total number of cells transmitted on this VCL. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.15 | ColumnciscoAtmVclCrossIfIndex | read-write | current | For point to point, this is the cross-connected VCL's ifIndex of this VCL. For point to multi-point connection, this will be the root VCL's ifIndex for a leaf … |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.16 | ColumnciscoAtmVclCrossVpi | read-write | current | This specifies the VPI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VPI for the leaf entr… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.17 | ColumnciscoAtmVclCrossVci | read-write | current | This specifies the VCI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VCI for the leaf entr… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.18 | ColumnciscoAtmVclNextLeafIfIndex | read-only | current | For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VCL's ifIndex on the multicast chain. This will… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.19 | ColumnciscoAtmVclNextLeafVpi | read-only | current | For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VPI on the multicast chain. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.20 | ColumnciscoAtmVclNextLeafVci | read-only | current | For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VCI on the multicast chain. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.21 | ColumnciscoAtmVclAalEncapFlag | read-write | current | Encapsulation type for terminating VC. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.22 | ColumnciscoAtmVclAalEncapProtocol | read-write | current | Protocol for terminating VC if EncapFlag is aal5Mux. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.23 | ColumnciscoAtmVclAalUserVcType | read-write | current | Following is the list of user virtual circuit types in case aal5Lane encapusation on this virtual channel. boxConfigure Configure VCC busForward busSend client… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.24 | ColumnciscoAtmVclAtmInArpInterval | read-write | current | Time interval in minutes to send InArp on a PVC for IP over ATM. 0 will disable the InArp for this pvc. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.25 | ColumnciscoAtmVclRemoteAddr | read-write | current | Soft PVC target address if this is the calling side Soft PVC source address if this is called side. Atomically set ConnState, RemoteAddr, RemoteVpi and RemoteV… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.26 | ColumnciscoAtmVclRemoteVpi | read-write | current | Soft PVC target VPI in calling side. 0 in called side. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.27 | ColumnciscoAtmVclRemoteVci | read-write | current | Soft PVC target VCI in calling side. 0 in called side. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.28 | ColumnciscoAtmVclLocation | read-only | current | Indicate calling or called side of a soft PVC. If ciscoAtmVclConfigType is not soft then ciscoAtmVclLocation value should be ignored. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.29 | ColumnciscoAtmVclSlowRetryIntv | read-write | current | Soft PVC slow retry interval in seconds. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.30 | ColumnciscoAtmVclNumAttempts | read-only | current | Number of retries made to install this soft PVC connection. If ciscoAtmVclConfigType is not soft then ciscoAtmVclNumAttempts value should be ignored. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.31 | ColumnciscoAtmVclLastReleaseCause | read-only | current | Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVC. Indicates the reason for the Release. … |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.32 | ColumnciscoAtmVclUpcViolations | read-only | current | The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VCL. On LS1010 systems, this counter is valid only… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.33 | ColumnciscoAtmVclEpdTpdCellDrops | read-only | obsolete | Never implemented. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.34 | ColumnciscoAtmVclEpdTpdPacketDrops | read-only | current | The total number of EPD/TPD packet drops of packets received on this VCL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, onl… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.35 | ColumnciscoAtmVclEpdTpdPacketsIn | read-only | current | The total number of packets received in their entirety on this VPL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only thos… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.37 | ColumnciscoAtmVclClp1Drops | read-only | obsolete | Never implemented. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.38 | ColumnciscoAtmVclDefaultRxUpcTolerance | read-only | current | If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified … |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.39 | ColumnciscoAtmVclDefaultRxUpcVbrCdvt | read-only | current | If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VCL creation, this objec… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.40 | ColumnciscoAtmVclLsPerVcqWrrWeight | read-write | current | Configure the weighting specified for a VC half-leg within a service class to make the scheduling decision among other active VCLs in the service class. This i… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.41 | ColumnciscoAtmVclLsPerVcqXmtQueuedCells | read-only | current | Number of cells received on this VCL and residing on the per-connection queue. Note that this value is not valid until the VCL is in an active cross-connect. T… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.42 | ColumnciscoAtmVclLsPerVcQThreshGrp | read-only | current | The Threshold Group to which the cell-queue for cells received by this VC are queued. Note that this value is not valid until the VCL is in an active cross-con… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.43 | ColumnciscoAtmVclInClp0Cells | read-only | current | The total number of cells with the CLP bit clear received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.44 | ColumnciscoAtmVclInClp1Cells | read-only | current | The total number of cells with the CLP bit set received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS10… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.45 | ColumnciscoAtmVclOutClp0Cells | read-only | current | The total number of cells with the CLP bit clear transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Car… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.46 | ColumnciscoAtmVclOutClp1Cells | read-only | current | The total number of cells with the CLP bit set transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card … |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.47 | ColumnciscoAtmVclCellDrops | read-only | current | The total number of cells received on this VCL, but discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flo… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.48 | ColumnciscoAtmVclClp0VcqFullCellDrops | read-only | current | The total number of cells received on this VCL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if E… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.49 | ColumnciscoAtmVclVcqClpThreshCellDrops | read-only | current | The total number of cells received on this VCL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and th… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.50 | ColumnciscoAtmVclRxNegTraffDescrIndex | read-only | current | Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VCL. This object is… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.51 | ColumnciscoAtmVclTxNegTraffDescrIndex | read-only | current | Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VCL. This object i… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.52 | ColumnciscoAtmVclSwFabOutCells | read-only | current | The total number of cells transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.53 | ColumnciscoAtmVclSwFabOutClp0Cells | read-only | current | The total number of cells with the CLP bit clear transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have supp… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.54 | ColumnciscoAtmVclSwFabOutClp1Cells | read-only | current | The total number of cells with the CLP bit set transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have suppor… |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.55 | ColumnciscoAtmVclConnName | read-write | current | A human readable string that identifies this connection. This object will return a zero-length string if value is not set. |
| 1.3.6.1.4.1.9.10.13.1.2.1.1.56 | ColumnciscoAtmVclConnType | read-write | current | This object represent the PVC Type for this connection. - local connection within the node - endToEnd across several nodes. This object serves as an informatio… |
| 1.3.6.1.4.1.9.10.13.1.3 | NodeciscoAtmSvp | |||
| 1.3.6.1.4.1.9.10.13.1.3.1 | TableciscoAtmSvpAddrTable | not-accessible | current | Switched virtual path link address table. |
| 1.3.6.1.4.1.9.10.13.1.3.1.1 | RowciscoAtmSvpAddrEntry | not-accessible | current | An entry in the Switched Vrtual Path address table. |
| 1.3.6.1.4.1.9.10.13.1.3.1.1.1 | ColumnciscoAtmSvpAddr | not-accessible | current | It depends on the direction.This could be p2pCallingSide address on a called side VPL, or p2pCalledSide address on a calling side VPL or p2mpRoot address on a … |
| 1.3.6.1.4.1.9.10.13.1.3.1.1.2 | ColumnciscoAtmSvpVpi | not-accessible | current | This SVP's VPI value on this interface. |
| 1.3.6.1.4.1.9.10.13.1.3.1.1.3 | ColumnciscoAtmSvpDirection | read-only | current | Indicate whether this VPL is calling side, called side, root or leaf for this address. |
| 1.3.6.1.4.1.9.10.13.1.4 | NodeciscoAtmSvc | |||
| 1.3.6.1.4.1.9.10.13.1.4.1 | TableciscoAtmSvcAddrTable | not-accessible | current | Switched virtual channel link address table. |
| 1.3.6.1.4.1.9.10.13.1.4.1.1 | RowciscoAtmSvcAddrEntry | not-accessible | current | An entry in the SVC address table. |
| 1.3.6.1.4.1.9.10.13.1.4.1.1.1 | ColumnciscoAtmSvcAddr | not-accessible | current | It depends on the direction.This could be p2pCallingSide address on a called side VCL, or p2pCalledSide address on a calling side VCL or p2mpRoot address on a … |
| 1.3.6.1.4.1.9.10.13.1.4.1.1.2 | ColumnciscoAtmSvcVpi | not-accessible | current | This SVC's VPI value on this interface. |
| 1.3.6.1.4.1.9.10.13.1.4.1.1.3 | ColumnciscoAtmSvcVci | not-accessible | current | This SVC's VCI value on this interface. |
| 1.3.6.1.4.1.9.10.13.1.4.1.1.4 | ColumnciscoAtmSvcDirection | read-only | current | Indicate whether this VCL is calling side, called side, root or leaf for this address. |
| 1.3.6.1.4.1.9.10.13.1.4.2 | ScalarciscoAtmSvcFrameDiscardUsesAal5Ie | read-write | current | Determines mechanism to use on interfaces to specify frame discard. Specifying a value of true causes the presence of the AAL5 IE to influence whether frame di… |
| 1.3.6.1.4.1.9.10.13.1.5 | NodeciscoAtmSnoopVc | |||
| 1.3.6.1.4.1.9.10.13.1.5.1 | TableciscoAtmSnoopVcTable | not-accessible | current | Snooping VC Table. |
| 1.3.6.1.4.1.9.10.13.1.5.1.1 | RowciscoAtmSnoopVcEntry | not-accessible | current | An entry in the Snoop VC table. This entry models a VC snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi and atmVclVci specifies… |
| 1.3.6.1.4.1.9.10.13.1.5.1.1.1 | ColumnciscoAtmSnoopVcSnoopedIfIndex | read-create | current | This specifies the ifIndex of the snooped interface. |
| 1.3.6.1.4.1.9.10.13.1.5.1.1.2 | ColumnciscoAtmSnoopVcSnoopedVpi | read-create | current | This specifies the VPI value of the snooped connection endpoint. |
| 1.3.6.1.4.1.9.10.13.1.5.1.1.3 | ColumnciscoAtmSnoopVcSnoopedVci | read-create | current | This specifies the VCI value of the snooped connection endpoint. |
| 1.3.6.1.4.1.9.10.13.1.5.1.1.4 | ColumnciscoAtmSnoopVcDir | read-create | current | This specifies the traffic direction at the snooped connection endpoint. |
| 1.3.6.1.4.1.9.10.13.1.5.1.1.5 | ColumnciscoAtmSnoopVcState | read-only | current | The connection state of this Snooping connetion. |
| 1.3.6.1.4.1.9.10.13.1.5.1.1.6 | ColumnciscoAtmSnoopVcRowStatus | read-create | current | This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vc snooping connection |
| 1.3.6.1.4.1.9.10.13.1.6 | NodeciscoAtmSnoopVp | |||
| 1.3.6.1.4.1.9.10.13.1.6.1 | TableciscoAtmSnoopVpTable | not-accessible | current | Snooping VP Table. |
| 1.3.6.1.4.1.9.10.13.1.6.1.1 | RowciscoAtmSnoopVpEntry | not-accessible | current | An entry in the Snoop VP table. This entry models a VP snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi specifies the VPI value… |
| 1.3.6.1.4.1.9.10.13.1.6.1.1.1 | ColumnciscoAtmSnoopVpSnoopedIfIndex | read-create | current | This specifies the ifIndex of the snooped interface. |
| 1.3.6.1.4.1.9.10.13.1.6.1.1.2 | ColumnciscoAtmSnoopVpSnoopedVpi | read-create | current | This specifies the VPI value of the snooped connection endpoint. |
| 1.3.6.1.4.1.9.10.13.1.6.1.1.3 | ColumnciscoAtmSnoopVpDir | read-create | current | This specifies the traffic direction at the snooped connection endpoint. |
| 1.3.6.1.4.1.9.10.13.1.6.1.1.4 | ColumnciscoAtmSnoopVpState | read-only | current | The connection state of this Snooping connection . |
| 1.3.6.1.4.1.9.10.13.1.6.1.1.5 | ColumnciscoAtmSnoopVpRowStatus | read-create | current | This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vp snooping connection |
| 1.3.6.1.4.1.9.10.13.3 | NodeciscoAtmConnMIBConformance | |||
| 1.3.6.1.4.1.9.10.13.3.1 | NodeciscoAtmConnMIBCompliances | |||
| 1.3.6.1.4.1.9.10.13.3.1.1 | ComplianceciscoAtmConnMIBCompliance | obsolete | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.1.2 | ComplianceciscoAtmConnMIBCompliance2 | obsolete | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.1.3 | ComplianceciscoAtmConnMIBCompliance3 | obsolete | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.1.4 | ComplianceciscoAtmConnMIBCompliance4 | obsolete | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.1.5 | ComplianceciscoAtmConnMIBCompliance5 | deprecated | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.1.6 | ComplianceciscoAtmConnMIBCompliance6 | deprecated | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.1.7 | ComplianceciscoAtmConnMIBCompliance7 | deprecated | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.1.8 | ComplianceciscoAtmConnMIBCompliance8 | current | The compliance statement for the Cisco ATM connection management group. | |
| 1.3.6.1.4.1.9.10.13.3.2 | NodeciscoAtmConnMIBGroups | |||
| 1.3.6.1.4.1.9.10.13.3.2.1 | GroupciscoAtmConnMIBGroup | deprecated | ||
| 1.3.6.1.4.1.9.10.13.3.2.2 | GroupciscoAtmConnMIBGroup2 | obsolete | ||
| 1.3.6.1.4.1.9.10.13.3.2.3 | GroupciscoAtmConnMIBGroup3 | current | ||
| 1.3.6.1.4.1.9.10.13.3.2.4 | GroupciscoAtmConnMIBlsPerVcqGroup | obsolete | A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset. | |
| 1.3.6.1.4.1.9.10.13.3.2.5 | GroupciscoAtmConnMIBlsFcPfqGroup | deprecated | A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card. | |
| 1.3.6.1.4.1.9.10.13.3.2.6 | GroupciscoAtmConnMIBlsPerVcqGroup2 | current | A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset. | |
| 1.3.6.1.4.1.9.10.13.3.2.7 | GroupciscoAtmConnMIBNegTraffGroup | current | A collection of objects to report negotiated traffic parameters on a Cisco ATM switch. | |
| 1.3.6.1.4.1.9.10.13.3.2.8 | GroupciscoAtmConnMIBlsFcPfqGroup1 | current | A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card. | |
| 1.3.6.1.4.1.9.10.13.3.2.9 | GroupciscoAtmConnMIBGroup1 | deprecated | ||
| 1.3.6.1.4.1.9.10.13.3.2.10 | GroupciscoAtmConnMIBGroup4 | current | ||
| 1.3.6.1.4.1.9.10.13.3.2.11 | GroupciscoAtmConnNmsGroup | current | A group of objects that provides additional information for a management system |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CastType | INTEGER { pointToPoint(1), pointToMultiPointRoot(2), pointToMultiPointLeaf(3) } | current | Specifies the type of the connection. It can be either a point to point connection or point to multipoint root or leaf. |
| ConfigType | INTEGER { other(1), permanent(2), switch(3), soft(4), softPassive(5) } | current | Specifies whether it's a permanent, switched, soft or soft passive config type. |
| ConnState | INTEGER { setup(1), release(2), notInstalled(3), down(4), up(5) } | current | The ConnState textual convention is used to specify different connection states. The connections states are: - 'setup', which indicates that the connection entry is to be created and installed in the hardware and softwa… |
| Direction | INTEGER { unknown(1), p2pCallingSide(2), p2pCalledSide(3), p2mpRoot(4), p2mpLeaf(5) } | current | Calling or called side associated with address. |
| EnableStatus | INTEGER { enable(1), disable(2) } | current | Enable or Disable operation. |
| Location | INTEGER { unknown(1), calling(2), called(3) } | current | Location of calling or called or unknown. |
| SnoopDirType | INTEGER { transmit(1), receive(2) } | current | Direction of Snooped Traffic |
| SpanType | INTEGER { unknown(1), transit(2), terminate(3), both(4) } | current | The SpanType textual convention is used to specify different connection span types. The connection span types are: - 'unknown', which indicates that the connection entry is not cross-connected. - 'transit', which indica… |
| UpcStatus | INTEGER { passing(1), tagging(2), dropping(3), localShaping(4) } | current | Define the Usage Parameter Control (UPC) operation as one of pass,tag or drop at this connection. |