CISCO-IPSLA-ETHERNET-MIB
246 objects
This MIB module consists of two parts. 1) Auto-Ethernet-CFM Control: | | 2) ethernetJitter Stats: | | | The first part defines a mechanism to manage IP SLA Auto-Ethernet-CFM operation. IP SLA is a capability which utilizes active monitoring for network perfomance. It can be used for network troubleshooting, network assessment and health monitoring. IEEE 802.1ag defines Connection Fault Management (CFM) for Ethernet layer. CFM can be used to detect, isolate and report the connectivity faults, and allows discovery and verification of the path through briges and LANs. Auto-Ethernet-CFM operation integrates the capabilities of IP SLA and IEEE 802.1ag. It's capable of discovering all the existing MEPs in a specified VLAN or Ethernet Virtual Connection within a specified maintenance domain. After which, it creates, configures, and schedules an IP SLA operation for each MEP automatically. IP SLA currently supports two types of operations for end-to-end Ethernet connectivity - 'ethernetPing' and 'ethernetJitter'. 'ethernetPing' can be used to monitor the connectivity and measure RTT by sending the regular 802.1ag loopback frame to a particular MEP. 'ethernetJitter' can be used to measure metrics such as RTT, Jitter, frame loss, one-way latency by sending multiple enhanced CFM frames at specified interval to a particular MEP. Without Auto-Ethernet-CFM operation, the two types of operations can also be created, configured, and scheduled manually through CISCO-RTTMON-MIB by specifing the target MEP's identifier in addition to the VLAN or Ethernet Virtual Connection and Maintenance Domain. With Auto-Ethernet-CFM operation, the two types of operations will be created automatically. The Auto-Ethernet-CFM will pass all the values specified in this module to the corresponding objects in CISCO-RTTMON-MIB for each MEP discovered. CISCO-IPSLA-ETHERNET-MIB CISCO-RTTMON-MIB ipslaEthernetGrpCtrlTable -> rttMonCtrlAdminTable | -> rttMonEchoAdminTable ipslaEthernetGrpReactTable -> rttMonReactTable The second part defines a collection of statistics resulting from 'ethernetJitter' operation created either manually or automatically. Glossary: CFM - Connection Fault Management DSAP - Domain Service Access Point: A member of a set of SAPs at which a Maintenance Domain is capable of offering connectivity to systems outside the Maintenance Domain. IP SLA - Cisco IOS IP Service Level Agreements IP SLA operation - Refers to the 'ethernetPing' or 'ethernetJitter' operation supported by IP SLA. MEP - Maintenance association End Point: An actively managed CFM entity, associated with a specific DSAP of a service instance, which can generate and receive CFM PDUs and track any responses. maintenance domain - The network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance. Maintenance Domain Name - The identifier, unique over the domain for which CFM is to protect against accidental concatenation of service instances, of a particular Maintenance Domain. RTT - Round Trip Time SAP - Service Access Point at which a service is offered. service instance - A service instance is a set of SAPs, selected from among the DSAPs defining a Maintenance Domain, such that a Data.Request primitive presented to one SAP can result in a Data.Indication primitive occurring at one or more of the other SAPs in the set. It corresponds to a VLAN or an Ethernet Virtual Connection. TLV - Stands for Type, Length, Value, and denotes a method of encoding variable-length and/or optional information in a PDU. TLVs are not aligned to any particular word or octet boundary. TLVs follow each other with no padding between TLVs. VLAN - Virtual Local Area Network: A subset of the active topology of a Bridged Local Area Network. Associated with each VLAN is a VLAN Identifier. REFERENCE: IEEE 802.1ag Draft 6.0 'Virtual Briged Local Area Networks - Amendments 5: Connectivity Fault Management' July 2006
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.585 | IdentityciscoIpSlaEthernetMIB | This MIB module consists of two parts. 1) Auto-Ethernet-CFM Control: | | 2) ethernetJitter Stats: | | | The first part defines a mechanism to manage IP SLA Aut… | ||
| 1.3.6.1.4.1.9.9.585.0 | NodeciscoIpSlaEthernetMIBNotifs | |||
| 1.3.6.1.4.1.9.9.585.1 | NodeciscoIpSlaEthernetMIBObjects | |||
| 1.3.6.1.4.1.9.9.585.1.1 | NodeipslaEthernetGrpCtrl | |||
| 1.3.6.1.4.1.9.9.585.1.1.1 | TableipslaEthernetGrpCtrlTable | not-accessible | current | This table contains Auto-Ethernet-CFM control data. When a row transition to the 'active' state, the IP SLA agent will discover all the MEPs inside the specifi… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1 | RowipslaEthernetGrpCtrlEntry | not-accessible | current | A collection of objects that define a conceptual Auto-Ethernet-CFM control row. The following objects must be specified in order to create this conceptual row.… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.1 | ColumnipslaEthernetGrpCtrlIndex | not-accessible | current | This object indicates a row in the ipslaEthernetGrpCtrlTable. This value is a pseudo-random number selected by the management station when creating a row via t… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.2 | ColumnipslaEthernetGrpCtrlStatus | read-create | current | This object specifies the status of Auto-Ethernet-CFM control row. Following objects must be specified in order for this object to become active. - ipslaEthern… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.3 | ColumnipslaEthernetGrpCtrlStorageType | read-create | current | This object specifies how the SNMP entity stores the data contained by the corresponding conceptual row. This object can be set to either 'volatile' or 'nonVol… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.4 | ColumnipslaEthernetGrpCtrlRttType | read-create | current | The type of IP SLA operation to be created by this Auto-Ethernet-CFM. This value can only be set to type 'ethernetPing' and 'ethernetJitter'. 'ethernetPing' op… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.5 | ColumnipslaEthernetGrpCtrlOwner | read-create | current | A string which used by a managing application to identify the entity that created this Auto-Ethernet-CFM. |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.6 | ColumnipslaEthernetGrpCtrlTag | read-create | current | A string which used by a managing application to identify the target VLAN and maintenance domain of this Auto-Ethernet-CFM. |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.7 | ColumnipslaEthernetGrpCtrlThreshold | read-create | current | This object specifies the threshold value of a particular object. This value will be examined for each IP SLA operations created by the Auto-Ethernet-CFM. For … |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.8 | ColumnipslaEthernetGrpCtrlTimeout | read-create | current | Specifies the duration to wait for an IP SLA operation created by this Auto-Ethernet-CFM to complete. For 'ethernetPing', if the value of rttMonLatestRttOperCo… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.9 | ColumnipslaEthernetGrpCtrlProbeList | read-only | current | This object indicates the identifiers of the IP SLA operations that are created by the Auto-Ethernet-CFM. The identifier will be stored in rttMonCtrlAdminIndex… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.10 | ColumnipslaEthernetGrpCtrlVLAN | read-create | current | This object specifies the identifier of VLAN for which the Auto-Ethernet-CFM operation will be used. It is an unique identifier for a service instance within a… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.11 | ColumnipslaEthernetGrpCtrlDomainNameType | read-create | current | This object specifies the type of maintenance domain name to be used by the Auto-Ethernet-CFM operation. This object can only be set to the following values: '… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.12 | ColumnipslaEthernetGrpCtrlDomainName | read-create | current | This object specifies the maintenance domain name to be used by the Auto-Ethernet-CFM operation. The Auto-Ethernet-CFM operation discovers all the MEPs partici… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.13 | ColumnipslaEthernetGrpCtrlReqDataSize | read-create | current | This object specifies the padding that needs to be inserted into each ethernet frame of the IP SLA operation. The total ethernet frame size of the IP SLA opera… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.14 | ColumnipslaEthernetGrpCtrlMPIDExLst | read-create | current | This object specifies the identifiers of the MEPs that will be excluded when create IP SLA operations by Auto-Ethernet-CFM operation. |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.15 | ColumnipslaEthernetGrpCtrlCOS | read-create | current | This object specifies the Class Of Service field in an Ethernet frame header. |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.16 | ColumnipslaEthernetGrpCtrlInterval | read-create | current | This value specifies the inter-frame delay between Ethernet frames that need to be transmitted to the target MEPs. This object is applicable to 'ethernetJitter… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.17 | ColumnipslaEthernetGrpCtrlNumFrames | read-create | current | This value specifies the number of Ethernet frames that need to be transmitted to the target MEPs. This object is applicable to 'ethernetJitter' operation only. |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.18 | ColumnipslaEthernetGrpScheduleRttStartTime | read-create | current | This object specifies the time when this conceptual row will become 'active'. ipslaEthernetGrpSchedulePeriod object must be specified before setting this objec… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.19 | ColumnipslaEthernetGrpSchedulePeriod | read-create | current | Specifies the time duration over which all the IP SLA operations created by the current Auto-Ethernet-CFM have to be scheduled. For instance, if there are thre… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.20 | ColumnipslaEthernetGrpScheduleFrequency | read-create | current | Specifies the duration between initiating each IP SLA operation created by the Auto-Ethernet-CFM. Take above example, if the ipslaEthernetGrpScheduleFrequency … |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.21 | ColumnipslaEthernetGrpCtrlEVC | read-create | current | This object specifies the Ethernet Virtual Connection for which the Auto-Ethernet-CFM operation will be used. It is an unique identifier for a service instance… |
| 1.3.6.1.4.1.9.9.585.1.1.1.1.22 | ColumnipslaEthernetGrpCtrlServiceInsType | read-create | current | This object specifies the type of service instance to be used by the Auto-Ethernet-CFM operation. When this object is set to value 'vlan', ipslaEthernetGrpCtrl… |
| 1.3.6.1.4.1.9.9.585.1.1.2 | TableipslaEthernetGrpReactTable | not-accessible | current | A table that contains the reaction configurations for Auto-Ethernet-CFM operation. The reaction configuration specifies the network perfomance parameter needs … |
| 1.3.6.1.4.1.9.9.585.1.1.2.1 | RowipslaEthernetGrpReactEntry | not-accessible | current | A collection of objects that define a conceptual Auto-Ethernet-CFM reaction configuration row. In order to create this conceptual row, ipslaEthernetGrpReactSta… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.1 | ColumnipslaEthernetGrpReactConfigIndex | not-accessible | current | This object along with ipslaEthernetGrpCtrlEntry identifies a particular reaction-configuration for a particular Auto-Ethernet-CFM operation. This is a pseudo-… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.2 | ColumnipslaEthernetGrpReactStatus | read-create | current | This objects specifies the status of the conceptual Auto-Ethernet-CFM reaction control row. Only 'createAndGo' and 'destroy' operations are permitted on the ro… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.3 | ColumnipslaEthernetGrpReactStorageType | read-create | current | This object specifies how the SNMP entity stores the data contained by the corresponding conceptual row. This object can be set to either 'volatile' or 'nonVol… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.4 | ColumnipslaEthernetGrpReactVar | read-create | current | This object specifies the performance parameter that will be monitored by the IP SLA operations which are created via Auto-Ethernet-CFM operation. The performa… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.5 | ColumnipslaEthernetGrpReactThresholdType | read-create | current | This object specifies the type of threshold violation that will trigger an notification. The notification will be sent accordingly only when the object rttMonR… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.6 | ColumnipslaEthernetGrpReactThresholdRising | read-create | current | This object specifies the higher threshold limit. If the value of monitored parameter ( e.g rtt, jitterAvg, packetLossSD etc ) rises above this limit and if th… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.7 | ColumnipslaEthernetGrpReactThresholdFalling | read-create | current | This object specifies the lower threshold limit. If the value of monitored parameter ( e.g rtt, jitterAvg, packetLossSD etc ) falls below this limit and if the… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.8 | ColumnipslaEthernetGrpReactThresholdCountX | read-create | current | If ipslaEthernetGrpReactThresholdType value is 'xOfy', this object specifies the 'x' value. If ipslaEthernetGrpReactThresholdType value is 'consecutive', this … |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.9 | ColumnipslaEthernetGrpReactThresholdCountY | read-create | current | This object specifies the 'y' value of the xOfy condition if ipslaEthernetGrpReactThresholdType is 'xOfy'. For other values of ipslaEthernetGrpReactThresholdTy… |
| 1.3.6.1.4.1.9.9.585.1.1.2.1.10 | ColumnipslaEthernetGrpReactActionType | read-create | current | This object specifies what type of reaction to generate if an IP SLA operation violates one of the watched conditions (specified in ipslaEthernetGrpReactVar): … |
| 1.3.6.1.4.1.9.9.585.1.2 | NodeipslaEthernetStats | |||
| 1.3.6.1.4.1.9.9.585.1.2.1 | TableipslaEtherJitterAggStatsTable | not-accessible | current | The 'ethernetJitter' statistics table contains summarized information of the results for a conceptual control row. A rolling accumulated history of this inform… |
| 1.3.6.1.4.1.9.9.585.1.2.1.1 | RowipslaEtherJitterAggStatsEntry | not-accessible | current | This entry contains the objects which accumulate the results of a series of 'ethernetJitter' operations over a 60 minute time period or a time period stored in… |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.1 | ColumnipslaEtherJAggStatsStartTimeId | not-accessible | current | The value of sysUpTime at the time when this row was created. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.2 | ColumnipslaEtherJAggMeasuredCmpletions | read-only | current | The number of Ethernet jitter operations that have completed successfully. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.3 | ColumnipslaEtherJAggMeasuredOvThrshlds | read-only | current | The number of Ethernet jitter operations that violate jitterAvg threshold which is defined in RttMonReactVar. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.4 | ColumnipslaEtherJAggMeasuredNumRTTs | read-only | current | The number of RTTs that are successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.5 | ColumnipslaEtherJAggMeasuredRTTSums | read-only | current | The sum of RTTs that are successfully measured for this ipslaEtherJAggMeasuredStartTimeId hourly group. The number of the successfully measured RTT is stored i… |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.6 | ColumnipslaEtherJAggMeasuredRTTSum2Ls | read-only | current | The sum of squares of RTTs that are successfully measured (low order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.7 | ColumnipslaEtherJAggMeasuredRTTSum2Hs | read-only | current | The sum of squares of RTTs that are successfully measured (high order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.8 | ColumnipslaEtherJAggMeasuredRTTMin | read-only | current | The minimum of RTTs that were successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.9 | ColumnipslaEtherJAggMeasuredRTTMax | read-only | current | The maximum of RTTs that were successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.10 | ColumnipslaEtherJAggMeasuredMinPosSD | read-only | current | The minimum of absolute values of all positive jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.11 | ColumnipslaEtherJAggMeasuredMaxPosSD | read-only | current | The maximum of absolute values of all positive jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.12 | ColumnipslaEtherJAggMeasuredNumPosSDs | read-only | current | The number of all positive jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.13 | ColumnipslaEtherJAggMeasuredSumPosSDs | read-only | current | The sum of all positive jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJAggMeasuredNumPosSDs. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.14 | ColumnipslaEtherJAggMeasuredSum2PSDLs | read-only | current | The sum of square of all positive jitter values for frames sent from source to destination (low order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.15 | ColumnipslaEtherJAggMeasuredSum2PSDHs | read-only | current | The sum of square of all positive jitter values for frames sent from source to destination (high order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.16 | ColumnipslaEtherJAggMeasuredMinNegSD | read-only | current | The minimum of all negative jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.17 | ColumnipslaEtherJAggMeasuredMaxNegSD | read-only | current | The maximum of all negative jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.18 | ColumnipslaEtherJAggMeasuredNumNegSDs | read-only | current | The number of all negative jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.19 | ColumnipslaEtherJAggMeasuredSumNegSDs | read-only | current | The sum of all negative jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJAggMeasuredNumNegSDs. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.20 | ColumnipslaEtherJAggMeasuredSum2NSDLs | read-only | current | The sum of square of all negative jitter values for frames sent from source to destination (low order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.21 | ColumnipslaEtherJAggMeasuredSum2NSDHs | read-only | current | The sum of square of all negative jitter values for frames sent from source to destination (high order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.22 | ColumnipslaEtherJAggMeasuredMinPosDS | read-only | current | The minimum of all positive jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.23 | ColumnipslaEtherJAggMeasuredMaxPosDS | read-only | current | The maximum of all positive jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.24 | ColumnipslaEtherJAggMeasuredNumPosDSes | read-only | current | The number of all positive jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.25 | ColumnipslaEtherJAggMeasuredSumPosDSes | read-only | current | The sum of all positive jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJAggMeasuredNumPosDSes. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.26 | ColumnipslaEtherJAggMeasuredSum2PDSLs | read-only | current | The sum of squares of all positive jitter values for frames sent from destination to source (low order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.27 | ColumnipslaEtherJAggMeasuredSum2PDSHs | read-only | current | The sum of squares of all positive jitter values for frames sent from destination to source (high order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.28 | ColumnipslaEtherJAggMeasuredMinNegDS | read-only | current | The minimum of all negative jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.29 | ColumnipslaEtherJAggMeasuredMaxNegDS | read-only | current | The maximum of all negative jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.30 | ColumnipslaEtherJAggMeasuredNumNegDSes | read-only | current | The number of all negative jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.31 | ColumnipslaEtherJAggMeasuredSumNegDSes | read-only | current | The sum of all negative jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJAggMeasuredNumNegDSes. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.32 | ColumnipslaEtherJAggMeasuredSum2NDSLs | read-only | current | The sum of squares of all negative jitter values for frames sent from destination to source (low order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.33 | ColumnipslaEtherJAggMeasuredSum2NDSHs | read-only | current | The sum of squares of all negative jitter values for frames sent from destination to source (high order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.34 | ColumnipslaEtherJAggMeasuredFrmLossSDs | read-only | current | The number of lost frames when sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.35 | ColumnipslaEtherJAggMeasuredFrmLssDSes | read-only | current | The number of lost frames when sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.36 | ColumnipslaEtherJAggMeasuredFrmOutSeqs | read-only | current | The number of frames arrived out of sequence. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.37 | ColumnipslaEtherJAggMeasuredFrmMIAes | read-only | current | The number of frames that are lost for which we cannot determine the direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.38 | ColumnipslaEtherJAggMeasuredFrmSkippds | read-only | current | The number of frames that are skipped per operation because the router could not send the packet out. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.39 | ColumnipslaEtherJAggMeasuredErrors | read-only | current | The number of occasions when an Ethernet jitter operation could not be initiated because of an internal error. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.40 | ColumnipslaEtherJAggMeasuredBusies | read-only | current | The number of occasions when an Ethernet jitter operation could not be initiated because a previous Ethernet jitter operation has not been completed. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.41 | ColumnipslaEtherJAggMeasuredOWSumSDs | read-only | current | The sum of one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.42 | ColumnipslaEtherJAggMeasuredOWSum2SDLs | read-only | current | The sum of squares of one way trip time from source to destination (low order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.43 | ColumnipslaEtherJAggMeasuredOWSum2SDHs | read-only | current | The sum of squares of one way trip time from source to destination (high order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.44 | ColumnipslaEtherJAggMeasuredOWMinSD | read-only | current | The minimum of all one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.45 | ColumnipslaEtherJAggMeasuredOWMaxSD | read-only | current | The maximum of all one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.46 | ColumnipslaEtherJAggMeasuredOWSumDSes | read-only | current | The sum of one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.47 | ColumnipslaEtherJAggMeasuredOWSum2DSLs | read-only | current | The sum of squares of one way trip time from destination to source (low order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.48 | ColumnipslaEtherJAggMeasuredOWSum2DSHs | read-only | current | The sum of squares of one way trip time from destination to source (high order 32 bits). |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.49 | ColumnipslaEtherJAggMeasuredOWMinDS | read-only | current | The minimum of all one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.50 | ColumnipslaEtherJAggMeasuredOWMaxDS | read-only | current | The maximum of all one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.51 | ColumnipslaEtherJAggMeasuredNumOWs | read-only | current | The number of one way trip time that are successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.52 | ColumnipslaEtherJAggMeasuredAvgJ | read-only | current | The average of positive and negative jitter values for source-to-destination and destination-to-source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.53 | ColumnipslaEtherJAggMeasuredAvgJSD | read-only | current | The average of positive and negative jitter values in source-to-destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.54 | ColumnipslaEtherJAggMeasuredAvgJDS | read-only | current | The average of positive and negative jitter values in destination-to-source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.55 | ColumnipslaEtherJAggMinSucFrmLoss | read-only | current | The minimum number of frames that are dropped successively. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.56 | ColumnipslaEtherJAggMaxSucFrmLoss | read-only | current | The maximum number of frames that are dropped successively. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.57 | ColumnipslaEtherJAggMeasuredIAJOut | read-only | current | Inter-arrival jitter (RFC 1889) at responder |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.58 | ColumnipslaEtherJAggMeasuredIAJIn | read-only | current | Inter-arrival jitter (RFC 1889) at sender |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.59 | ColumnipslaEtherJAggMeasuredFrmLateAs | read-only | current | The number of frames that arrived after the timeout. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.60 | ColumnipslaEtherJAggMeasuredFrmUnPrcds | read-only | current | The number of frames that arrived but could not be processed due to the internal error. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.61 | ColumnipslaEtherJAggMeasuredMaxPosTW | read-only | current | The two-way maximum of all positive jitter values for frames. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.62 | ColumnipslaEtherJAggMeasuredMaxNegTW | read-only | current | The two-way maximum of all negative jitter values for frames. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.63 | ColumnipslaEtherJAggMeasuredMinPosTW | read-only | current | The two-way minimum of all positive jitter values for frames. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.64 | ColumnipslaEtherJAggMeasuredMinNegTW | read-only | current | The two-way minimum of all negative jitter values for frames. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.65 | ColumnipslaEtherJAggMeasuredTxFrmsSD | read-only | current | The number of data frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.66 | ColumnipslaEtherJAggMeasuredTxFrmsDS | read-only | current | The number of data frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.67 | ColumnipslaEtherJAggMeasuredRxFrmsSD | read-only | current | The number of data frames received from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.68 | ColumnipslaEtherJAggMeasuredRxFrmsDS | read-only | current | The number of data frames received from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.69 | ColumnipslaEtherJAggMeasuredMinLossNumeratorSD | read-only | current | The numerator for the minimum loss ratio recorded in the source to destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.70 | ColumnipslaEtherJAggMeasuredMinLossDenominatorSD | read-only | current | The denominator for the minimum loss ratio recorded in the source to destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.71 | ColumnipslaEtherJAggMeasuredMaxLossNumeratorSD | read-only | current | The numerator for the maximum loss ratio recorded in the source to destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.72 | ColumnipslaEtherJAggMeasuredMaxLossDenominatorSD | read-only | current | The denominator for the maximum loss ratio recorded in the source to destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.73 | ColumnipslaEtherJAggMeasuredAvgLossNumeratorSD | read-only | current | The numerator for the average loss ratio recorded in the source to destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.74 | ColumnipslaEtherJAggMeasuredAvgLossDenominatorSD | read-only | current | The denominator for the average loss ratio recorded in the source to destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.75 | ColumnipslaEtherJAggMeasuredMinLossNumeratorDS | read-only | current | The numerator for the minimum loss ratio recorded in the destination to source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.76 | ColumnipslaEtherJAggMeasuredMinLossDenominatorDS | read-only | current | The denominator for the minimum loss ratio recorded in the destination to source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.77 | ColumnipslaEtherJAggMeasuredMaxLossNumeratorDS | read-only | current | The numerator for the maximum loss ratio recorded in the destination to source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.78 | ColumnipslaEtherJAggMeasuredMaxLossDenominatorDS | read-only | current | The denominator for the maximum loss ratio recorded in the destination to source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.79 | ColumnipslaEtherJAggMeasuredAvgLossNumeratorDS | read-only | current | The numerator for the average loss ratio recorded in the destination to source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.80 | ColumnipslaEtherJAggMeasuredAvgLossDenominatorDS | read-only | current | The denominator for the average loss ratio recorded in the destination to source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.81 | ColumnipslaEtherJAggMeasuredCumulativeLossNumeratorSD | read-only | current | The numerator for the loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.82 | ColumnipslaEtherJAggMeasuredCumulativeLossDenominatorSD | read-only | current | The denominator for the loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.83 | ColumnipslaEtherJAggMeasuredCumulativeAvgLossNumeratorSD | read-only | current | The numerator for the average loss ratio recorded in the source to destination direction. This value is cumulative over the perios of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.84 | ColumnipslaEtherJAggMeasuredCumulativeAvgLossDenominatorSD | read-only | current | The denominator for the average loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.85 | ColumnipslaEtherJAggMeasuredCumulativeLossNumeratorDS | read-only | current | The numerator for the loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.86 | ColumnipslaEtherJAggMeasuredCumulativeLossDenominatorDS | read-only | current | The denominator for the loss ratio recorded in the destination to source direction. This valued is cumulative over the period of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.87 | ColumnipslaEtherJAggMeasuredCumulativeAvgLossNumeratorDS | read-only | current | The numerator for the average loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.88 | ColumnipslaEtherJAggMeasuredCumulativeAvgLossDenominatorDS | read-only | current | The denominator for the average loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.89 | ColumnipslaEtherJAggMeasuredNumOverThresh | read-only | current | The number of RTTs that were over the threshold value. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.90 | ColumnipslaEtherJAggLossMeasurementRate | read-only | current | Loss Measurement rate from source to destination |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.91 | ColumnipslaEtherDelayAggMeasuredRTTMin | read-only | current | The minimum of RTTs that were successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.92 | ColumnipslaEtherDelayAggMeasuredRTTMax | read-only | current | The maximum of RTTs that were successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.93 | ColumnipslaEtherDelayAggMeasuredRTTSums | read-only | current | The sum of RTTs that are successfully measured for this ipslaEtherJAggMeasuredStartTimeId hourly group. The number of the successfully measured RTT is stored i… |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.94 | ColumnipslaEtherDelayAggMeasuredOWMinSD | read-only | current | The minimum of all one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.95 | ColumnipslaEtherDelayAggMeasuredOWMaxSD | read-only | current | The maximum of all one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.96 | ColumnipslaEtherDelayAggMeasuredOWSumSDs | read-only | current | The sum of all one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.97 | ColumnipslaEtherDelayAggMeasuredOWMinDS | read-only | current | The minimum of all one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.98 | ColumnipslaEtherDelayAggMeasuredOWMaxDS | read-only | current | The maximum of all one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.99 | ColumnipslaEtherDelayAggMeasuredOWSumDSes | read-only | current | The sum of all one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.100 | ColumnipslaEtherDelayAggMeasuredMinPosSD | read-only | current | The minimum of all positive jitter values for the frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.101 | ColumnipslaEtherDelayAggMeasuredMaxPosSD | read-only | current | The maximum of all positive jitter values for the frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.102 | ColumnipslaEtherDelayAggMeasuredSumPosSDs | read-only | current | The sum of all positive jitter values for frames sent from source to destination. The number of such values stored in ipslaEtherJAggMeasuredNumPosSDs. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.103 | ColumnipslaEtherDelayAggMeasuredMinNegSD | read-only | current | The minimum of all negative jitter values for the frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.104 | ColumnipslaEtherDelayAggMeasuredMaxNegSD | read-only | current | The maximum of all negative jitter values for the frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.105 | ColumnipslaEtherDelayAggMeasuredSumNegSDs | read-only | current | The sum of all negative jitter values for the frames sent from source to destination. The number of such values is stored in ipslaEtherJAggMeasuredNumNegSDs. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.106 | ColumnipslaEtherDelayAggMeasuredMinPosDS | read-only | current | The minimum of all positive jitter values for the frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.107 | ColumnipslaEtherDelayAggMeasuredMaxPosDS | read-only | current | The maximum of all positive jitter values for the frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.108 | ColumnipslaEtherDelayAggMeasuredSumPosDSes | read-only | current | The sum of all positive jitter values for the frames sent from destination to source. The number of such values is stored in ipslaEtherJAggMeasuredNumPosDSes. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.109 | ColumnipslaEtherDelayAggMeasuredMinNegDS | read-only | current | The minimum of all negative jitter values for the frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.110 | ColumnipslaEtherDelayAggMeasuredMaxNegDS | read-only | current | The maximum of all negative jitter values for the frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.111 | ColumnipslaEtherDelayAggMeasuredSumNegDSes | read-only | current | The sum of all negative jitter values for the frames sent |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.112 | ColumnipslaEtherDelayAggMeasuredMinPosTW | read-only | current | The minimum of all two-way postive jitter values. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.113 | ColumnipslaEtherDelayAggMeasuredMaxPosTW | read-only | current | The maximum of all two-way postive jitter values. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.114 | ColumnipslaEtherDelayAggMeasuredSumPosTW | read-only | current | The sum of all two-way positive jitter values. The number of such values is stored in ipslaEtherDelayAggMeasuredNumPosTW. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.115 | ColumnipslaEtherDelayAggMeasuredNumPosTW | read-only | current | The number of two-way positive jitter measurements that are successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.116 | ColumnipslaEtherDelayAggMeasuredMinNegTW | read-only | current | The minimum of all two-way negative jitter values. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.117 | ColumnipslaEtherDelayAggMeasuredMaxNegTW | read-only | current | The maximum of all two-way negative jitter values. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.118 | ColumnipslaEtherDelayAggMeasuredSumNegTW | read-only | current | The sum of all two-way negative jitter values. The number of such values is stored in ipslaEtherDelayAggMeasuredNumNegTW. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.119 | ColumnipslaEtherDelayAggMeasuredNumNegTW | read-only | current | The number of two-way negative jitter measurements that are successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.120 | ColumnipslaEtherDelayAggMeasuredAvgJSD | read-only | current | The average of positive and negative jitter values in source to destination direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.121 | ColumnipslaEtherDelayAggMeasuredAvgJDS | read-only | current | The average of positive and negative jitter values in destination to source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.122 | ColumnipslaEtherDelayAggMeasuredAvgJ | read-only | current | The average of positive and negative jitter values for source-to-destination and destination-to-source direction. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.123 | ColumnipslaEtherDelayAggMeasuredTWAvgJ | read-only | current | The average of two-way positive and negative jitter values. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.124 | ColumnipslaEtherLossAggMeasuredLostFrmsSD | read-only | current | The number of data frames lost from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.2.1.1.125 | ColumnipslaEtherLossAggMeasuredLostFrmsDS | read-only | current | The number of data frames lost from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.2.2 | TableipslaEtherJitterAggBinTable | not-accessible | current | This table contains summarized information of the forward/backward/two-way delay bin and forward positive/negative, backward positive/negative and two-way posi… |
| 1.3.6.1.4.1.9.9.585.1.2.2.1 | RowipslaEtherJitterAggBinEntry | not-accessible | current | This entry contains the objects which accumulate the results of a series of ethernet delay operation over the aggregate interval time period or a time period s… |
| 1.3.6.1.4.1.9.9.585.1.2.2.1.1 | ColumnipslaEtherJAggStatsBinStartTimeId | not-accessible | current | The value of sysUpTime at the time when this row was created. |
| 1.3.6.1.4.1.9.9.585.1.2.2.1.2 | ColumnipslaEtherJAggStatsBinType | not-accessible | current | The type of the jitter statistics bin. |
| 1.3.6.1.4.1.9.9.585.1.2.2.1.3 | ColumnipslaEtherJAggStatsBinLowerRange | not-accessible | current | The lower range of the bin in microseconds. |
| 1.3.6.1.4.1.9.9.585.1.2.2.1.4 | ColumnipslaEtherJAggStatsBinUpperRange | not-accessible | current | The upper range of the bin in microseconds. |
| 1.3.6.1.4.1.9.9.585.1.2.2.1.5 | ColumnipslaEtherJAggStatsBinObservation | read-only | current | The number of observations with in the lower and upper bin range. |
| 1.3.6.1.4.1.9.9.585.1.3 | NodeipslaEthernetLatestOper | |||
| 1.3.6.1.4.1.9.9.585.1.3.1 | TableipslaEtherJitterLatestStatsTable | not-accessible | current | The 'ethernetJitter' operation sends out frames at the frequency specified by rttMonCtrlAdminFrequency. This table contains the statistics calculated for the l… |
| 1.3.6.1.4.1.9.9.585.1.3.1.1 | RowipslaEtherJitterLatestStatsEntry | not-accessible | current | A collection of objects that record the latest Ethernet jitter operation. An entry is created only when the following objects are valid. - rttMonCtrlAdminRttTy… |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.1 | ColumnipslaEtherJitterLatestNumRTT | read-only | current | The number of RTT's that were successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.2 | ColumnipslaEtherJitterLatestRTTSum | read-only | current | The sum of RTT's that are successfully measured. The number of successfully measured RTT is stored in ipslaEtherJitterLatestNumRTT. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.3 | ColumnipslaEtherJitterLatestRTTSum2 | read-only | current | The sum of squares of RTT's that are successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.4 | ColumnipslaEtherJitterLatestRTTMin | read-only | current | The minimum of RTT's that were successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.5 | ColumnipslaEtherJitterLatestRTTMax | read-only | current | The maximum of RTT's that were successfully measured. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.6 | ColumnipslaEtherJitterLatestMinPosSD | read-only | current | The minimum of all positive jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.7 | ColumnipslaEtherJitterLatestMaxPosSD | read-only | current | The maximum of all positive jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.8 | ColumnipslaEtherJitterLatestNumPosSD | read-only | current | The number of all positive jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.9 | ColumnipslaEtherJitterLatestSumPosSD | read-only | current | The sum of all positive jitter values for frames sent source to destination. The number of such values is stored in ipslaEtherJitterLatestNumPosSD. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.10 | ColumnipslaEtherJitterLatestSum2PosSD | read-only | current | The sum of square of all positive jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.11 | ColumnipslaEtherJitterLatestMinNegSD | read-only | current | The minimum of absolute values of all negative jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.12 | ColumnipslaEtherJitterLatestMaxNegSD | read-only | current | The maximum of absolute values of all negative jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.13 | ColumnipslaEtherJitterLatestNumNegSD | read-only | current | The number of all negative jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.14 | ColumnipslaEtherJitterLatestSumNegSD | read-only | current | The sum of all negative jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJitterLatestNumNegSD. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.15 | ColumnipslaEtherJitterLatestSum2NegSD | read-only | current | The sum of square of all negative jitter values for frames sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.16 | ColumnipslaEtherJitterLatestMinPosDS | read-only | current | The minimum of all positive jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.17 | ColumnipslaEtherJitterLatestMaxPosDS | read-only | current | The maximum of all positive jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.18 | ColumnipslaEtherJitterLatestNumPosDS | read-only | current | The number of all positive jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.19 | ColumnipslaEtherJitterLatestSumPosDS | read-only | current | The sum of all positive jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJitterLatestNumPosDS. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.20 | ColumnipslaEtherJitterLatestSum2PosDS | read-only | current | The sum of squares of all positive jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.21 | ColumnipslaEtherJitterLatestMinNegDS | read-only | current | The minimum of all negative jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.22 | ColumnipslaEtherJitterLatestMaxNegDS | read-only | current | The maximum of all negative jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.23 | ColumnipslaEtherJitterLatestNumNegDS | read-only | current | The number of all negative jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.24 | ColumnipslaEtherJitterLatestSumNegDS | read-only | current | The sum of all negative jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJitterLatestNumNegDS. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.25 | ColumnipslaEtherJitterLatestSum2NegDS | read-only | current | The sum of squares of all negative jitter values for frames sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.26 | ColumnipslaEtherJitterLatestFrmLossSD | read-only | current | The number of frames lost when sent from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.27 | ColumnipslaEtherJitterLatestFrmLossDS | read-only | current | The number of frames lost when sent from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.28 | ColumnipslaEtherJitterLatestFrmOutSeq | read-only | current | The number of frames arrived out of sequence. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.29 | ColumnipslaEtherJitterLatestFrmMIA | read-only | current | The number of frames that are lost for which we cannot determine the direction. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.30 | ColumnipslaEtherJitterLatestFrmSkipped | read-only | current | The number of frames in the operation that could not be initiated due to an internal error. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.31 | ColumnipslaEtherJitterLatestSense | read-only | current | An application specific sense code for the completion status. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.32 | ColumnipslaEtherJitterLatestFrmLateA | read-only | current | The number of frames that arrived after the timeout. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.33 | ColumnipslaEtherJitterLatestMinSucFrmL | read-only | current | The minimum number of frames that are dropped successively. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.34 | ColumnipslaEtherJitterLatestMaxSucFrmL | read-only | current | The maximum number of frames that are dropped successively. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.35 | ColumnipslaEtherJitterLatestOWSumSD | read-only | current | The sum of one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.36 | ColumnipslaEtherJitterLatestOWSum2SD | read-only | current | The sum of squares of one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.37 | ColumnipslaEtherJitterLatestOWMinSD | read-only | current | The minimum of all one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.38 | ColumnipslaEtherJitterLatestOWMaxSD | read-only | current | The maximum of all one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.39 | ColumnipslaEtherJitterLatestOWSumDS | read-only | current | The sum of one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.40 | ColumnipslaEtherJitterLatestOWSum2DS | read-only | current | The sum of squares of one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.41 | ColumnipslaEtherJitterLatestOWMinDS | read-only | current | The minimum of all one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.42 | ColumnipslaEtherJitterLatestOWMaxDS | read-only | current | The maximum of all one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.43 | ColumnipslaEtherJitterLatestNumOW | read-only | current | The number of successful one way trip time measurements. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.44 | ColumnipslaEtherJitterLatestAvgJitter | read-only | current | The average of positive and negative jitter values in Source-to-Destination and Destination-to-Source direction. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.45 | ColumnipslaEtherJitterLatestAvgSDJ | read-only | current | The average of positive and negative jitter values from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.46 | ColumnipslaEtherJitterLatestAvgDSJ | read-only | current | The average of positive and negative jitter values from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.47 | ColumnipslaEtherJitterLatestOWAvgSD | read-only | current | The average one way trip time from source to destination. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.48 | ColumnipslaEtherJitterLatestOWAvgDS | read-only | current | The average one way trip time from destination to source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.49 | ColumnipslaEtherJitterLatestIAJOut | read-only | current | Inter-arrival jitter (RFC 1889) at responder. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.50 | ColumnipslaEtherJitterLatestIAJIn | read-only | current | Inter-arrival jitter (RFC 1889) at source. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.51 | ColumnipslaEtherJLatestFrmUnProcessed | read-only | current | The number of frames in the operation that could not be processed due to high CPU load. |
| 1.3.6.1.4.1.9.9.585.1.3.1.1.52 | ColumnipslaEtherJitterLatestNumOverThresh | read-only | current | The number of RTT's that were over the threshold value. |
| 1.3.6.1.4.1.9.9.585.2 | NodeciscoIpSlaEthernetMIBConform | |||
| 1.3.6.1.4.1.9.9.585.2.1 | NodeciscoIpSlaEthernetCompliances | |||
| 1.3.6.1.4.1.9.9.585.2.1.1 | ComplianceciscoIpSlaEthernetCompliance | deprecated | The compliance statement for (1) Ethernet Jitter operation and statistics | |
| 1.3.6.1.4.1.9.9.585.2.1.2 | ComplianceciscoIpSlaEthernetComplianceRev2 | deprecated | The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Auto-Ethernet-CFM | |
| 1.3.6.1.4.1.9.9.585.2.1.3 | ComplianceciscoIpSlaEthernetComplianceRev3 | current | The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Y1731 | |
| 1.3.6.1.4.1.9.9.585.2.1.4 | ComplianceciscoIpSlaEthernetComplianceRev4 | deprecated | The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Y1731 | |
| 1.3.6.1.4.1.9.9.585.2.1.5 | ComplianceciscoIpSlaEthernetComplianceRev5 | deprecated | The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Y1731 (3) supporting IP SLA Y1731 Bin statistics | |
| 1.3.6.1.4.1.9.9.585.2.1.6 | ComplianceciscoIpSlaEthernetComplianceRev6 | current | The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Y1731 | |
| 1.3.6.1.4.1.9.9.585.2.2 | NodeciscoIpSlaEthernetMIBGroups | |||
| 1.3.6.1.4.1.9.9.585.2.2.1 | GroupciscoIpSlaEthernetAutoGroup | current | A collection of objects that were added to support Auto-Ethernet-CFM. | |
| 1.3.6.1.4.1.9.9.585.2.2.2 | GroupciscoIpSlaEthernetStatsGroup | current | A collection of statistics objects related to Ethernet Jitter Probe. | |
| 1.3.6.1.4.1.9.9.585.2.2.3 | GroupciscoIpSlaEthernetAutoEVCGroup | current | A collection of objects which provides the support for Auto-Ethernet-CFM ping/jitter operation with Ethernet Virtual Connection. | |
| 1.3.6.1.4.1.9.9.585.2.2.4 | GroupciscoIpSlaEthernetY1731Group | current | A collection of objects which provides the support for Y1731 operation with Ethernet Virtual Connection. | |
| 1.3.6.1.4.1.9.9.585.2.2.5 | GroupciscoIpSlaEthernetOverThreshGroup | current | A collection of objects which provides the support for Over Threshold statistics for Ethernet Jitter. | |
| 1.3.6.1.4.1.9.9.585.2.2.6 | GroupciscoIpSlaEthernetY1731BinStatsGroup | current | A collection of objects which provides the support for Y1731 Statistics Bin. | |
| 1.3.6.1.4.1.9.9.585.2.2.7 | GroupciscoIpSlaEthernetDelayStatsGroup | current | A collection of objects which provides the Y1731 delay and delay variance with microsecond unit. |