CISCO-LWAPP-QOS-MIB
304 objects
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is used to study the quality of service in the voice and video traffic on the WLAN. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Gratuitous Probe Response (GPR) The Gratuitous Probe Response feature aids in conserving battery power of WLAN-enabled cell phones by providing a high rate packet on the order of tens of milliseconds such that these kind of phones can wake up and wait at predefined intervals, to reduce battery power. The GPR packet is transmitted from the AP at a predefined time interval. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. TU A measurement of time in units of 1024 microseconds. User Priority ( UP ) Specifies a the priority rules in QOS for handling user priority. EDCA (Enhanced distributed channel access) As defined in 802.11e standard, Enhanced distributed channel access(EDCA) parameter set element is used by the AP to establish policy, to change policy when accepting new clients, or to adapt to changes in offered load. RRC (Resource Reservation Control) Wireless LAN Controller will periodically send this message to AP in order to collect various radio and client statistics, which will be feed in to RRC algorithm. This message will be sent per access class (i.e. 802.11 band) at the time of admission and re-RRC calculations. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
Imported Objects
| CISCO-LWAPP-AP-MIB | cLApDot11IfEntry cLApDot11IfSlotId cLApDot11IfType cLApName cLApSysMacAddress |
| CISCO-LWAPP-DOT11-CLIENT-MIB | cldcClientMacAddress |
| CISCO-LWAPP-WLAN-MIB | cLWlanConfigEntry cLWlanIndex |
| CISCO-QOS-PIB-MIB | Percent |
| CISCO-SMI | ciscoMgmt |
| CISCO-TC | CiscoURLStringOrEmpty TimeIntervalSec |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus StorageType TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.524 | IdentityciscoLwappQosMIB | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from… | ||
| 1.3.6.1.4.1.9.9.524.0 | NodeciscoLwappQosMIBNotifs | |||
| 1.3.6.1.4.1.9.9.524.0.1 | NotificationciscoLwappVoipCallFailureNotif | current | This notification is generated when ever a VOIP call failure occurs. | |
| 1.3.6.1.4.1.9.9.524.0.2 | NotificationciscoLwappMediaMCStreamFailureNotif | current | This notification is generated when ever a multicast to unicast Media conversion failure occurs. AP MAC Address and slotID will be sent as index for AP related… | |
| 1.3.6.1.4.1.9.9.524.0.3 | NotificationciscoLwappMediaMCStreamAdmitNotif | current | This notification is generated when ever a client gets admitted to the stream. AP MAC Address and slotID will be sent as index for AP related objects. | |
| 1.3.6.1.4.1.9.9.524.0.4 | NotificationciscoLwappMediaMCStreamDelistNotif | current | This notification is generated when ever a client delists from the stream. AP MAC Address and slotID will be sent as index for AP related objects. | |
| 1.3.6.1.4.1.9.9.524.1 | NodeciscoLwappQosMIBObjects | |||
| 1.3.6.1.4.1.9.9.524.1.1 | NodecLQd11aCACConfig | |||
| 1.3.6.1.4.1.9.9.524.1.1.1 | ScalarcLQd11aVoiceAdmCtrlSupport | read-write | current | This object is used to enable or disable admission control for voice traffic flowing through the 802.11a interfaces in the controller. When set to 'true', cont… |
| 1.3.6.1.4.1.9.9.524.1.1.2 | ScalarcLQd11aVoiceMaxAdmBandwidth | read-write | current | This object denotes the maximum bandwidth that can be allocated by controller for voice traffic when admission control is enabled for for 802.11a interfaces in… |
| 1.3.6.1.4.1.9.9.524.1.1.3 | ScalarcLQd11aVoiceMaxRoamBandwidth | read-write | current | This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11aVoiceMaxAdmBandwidth, that can be allocated to roaming cli… |
| 1.3.6.1.4.1.9.9.524.1.1.4 | ScalarcLQd11aVideoAdmCtrlSupport | read-write | current | This object is used to enable or disable admission control for video traffic flowing through the 802.11a interfaces in the controller. When set to 'true', cont… |
| 1.3.6.1.4.1.9.9.524.1.1.5 | ScalarcLQd11aVideoMaxAdmBandwidth | read-write | current | This object denotes the maximum bandwidth that can be allocated by controller for video traffic when admission control is enabled for 802.11a interfaces in the… |
| 1.3.6.1.4.1.9.9.524.1.1.6 | ScalarcLQd11aVideoMaxRoamBandwidth | read-write | current | This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11aVideoMaxAdmBandwidth, that can be allocated to roaming cli… |
| 1.3.6.1.4.1.9.9.524.1.1.7 | ScalarcLQd11aGprProbeInterval | read-write | current | This object specifies the GPR probe interval period to be used by all 802.11a interfaces in the controller. The radios are advertising any WLAN with GPR suppor… |
| 1.3.6.1.4.1.9.9.524.1.1.8 | ScalarcLQd11aVoiceCtrl | read-write | current | This object specifies the parameters that can be modified, when admission control is enabled. loadBased - controller will reserve and manage max-bandwidth and … |
| 1.3.6.1.4.1.9.9.524.1.1.9 | ScalarcLQd11aExpeditedBw | read-write | current | This object specifies if expedited BW feature is enabled or not. A value of 'true' will ensure that the APs advertise the expedited BW support in their beacons… |
| 1.3.6.1.4.1.9.9.524.1.1.10 | ScalarcLQd11aEdcaProfile | read-write | current | This object specifies the EDCA profile to be used in EDCA Parameter set element. wmmDefault - WMM default standard parameters. svpVoice - Spectralink voice pri… |
| 1.3.6.1.4.1.9.9.524.1.1.11 | ScalarcLQd11aMacOptimization | read-write | current | This object specifies MAC enhancements for voice, resulting in improvement in number of voice calls serviced per access point. A value of 'true' enables MAC op… |
| 1.3.6.1.4.1.9.9.524.1.1.12 | ScalarcLQd11aMaxCallLimit | read-write | deprecated | This object specifies the maximum number of CAC Voice Calls allowed on dot11a radio band. Value of zero denotes no limit. No replacement object. |
| 1.3.6.1.4.1.9.9.524.1.1.13 | ScalarcLQd11aMcastDirectEnable | read-write | current | This object specifies the decision flag to allow multicast direct stream on radio. |
| 1.3.6.1.4.1.9.9.524.1.1.14 | ScalarcLQd11aBestEffortAdmission | read-write | current | This object specifies whether to admit a media stream in best effort queue. |
| 1.3.6.1.4.1.9.9.524.1.1.15 | ScalarcLQd11aRedirectBestEffort | read-write | current | This object specifies whether a unicast or multicast only video stream can be redirected to best effort. |
| 1.3.6.1.4.1.9.9.524.1.1.16 | ScalarcLQd11aRadioMaxStreams | read-write | current | This object specifies the maximum number of allowed streams per radio for a 802.11a band. |
| 1.3.6.1.4.1.9.9.524.1.1.17 | ScalarcLQd11aMaxVideoATPercent | read-write | current | This object specifies the maximum allowed bandwidth for video traffic. |
| 1.3.6.1.4.1.9.9.524.1.1.18 | ScalarcLQd11aMaxVoiceATPercent | read-write | current | This object specifies the maximum allowed bandwidth for voice traffic. |
| 1.3.6.1.4.1.9.9.524.1.1.19 | ScalarcLQd11aMaxMediaATPercent | read-write | current | This object specifies the maximum allowed bandwidth for media traffic. |
| 1.3.6.1.4.1.9.9.524.1.1.20 | ScalarcLQd11aMinPhyRate | read-write | current | This object specifies the minimum physical rate that should be enabled by a client to successfully join a media stream. |
| 1.3.6.1.4.1.9.9.524.1.1.21 | ScalarcLQd11aClientMaxStreams | read-write | current | This object specifies the maximum number of allowed streams per client for a 802.11a band. |
| 1.3.6.1.4.1.9.9.524.1.1.22 | ScalarcLQd11aSipCacSupportEnable | read-write | current | This object specifies whether SIP CAC is enabled. A value of 'true' enables SIP CAC on dot11a radio band. A value of 'true' disables SIP CAC on dot11a radio ba… |
| 1.3.6.1.4.1.9.9.524.1.2 | NodecLQd11bCACConfig | |||
| 1.3.6.1.4.1.9.9.524.1.2.1 | ScalarcLQd11bVoiceAdmCtrlSupport | read-write | current | This object is used to enable or disable admission control for voice traffic flowing through the 802.11b/g interfaces in the controller. When set to 'true', co… |
| 1.3.6.1.4.1.9.9.524.1.2.2 | ScalarcLQd11bVoiceMaxAdmBandwidth | read-write | current | This object denotes the maximum bandwidth that can be allocated by controller for voice traffic when admission control is enabled for 802.11b/g interfaces in t… |
| 1.3.6.1.4.1.9.9.524.1.2.3 | ScalarcLQd11bVoiceMaxRoamBandwidth | read-write | current | This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11bVoiceMaxAdmBandwidth, that can be allocated to roaming cli… |
| 1.3.6.1.4.1.9.9.524.1.2.4 | ScalarcLQd11bVideoAdmCtrlSupport | read-write | current | This object is used to enable or disable admission control for video traffic flowing through the 802.11b/g interfaces in the controller. When set to 'true', co… |
| 1.3.6.1.4.1.9.9.524.1.2.5 | ScalarcLQd11bVideoMaxAdmBandwidth | read-write | current | This object denotes the maximum bandwidth that can be allocated by controller for video traffic when admission control is enabled for 802.11b/g interfaces in t… |
| 1.3.6.1.4.1.9.9.524.1.2.6 | ScalarcLQd11bVideoMaxRoamBandwidth | read-write | current | This objects represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11bVideoMaxAdmBandwidth, that can be allocated to roaming cl… |
| 1.3.6.1.4.1.9.9.524.1.2.7 | ScalarcLQd11bGprProbeInterval | read-write | current | This object is used to set GPR probe interval period to be used by all 802.11b/g interfaces in the controller, when the radios are advertising any WLAN with GP… |
| 1.3.6.1.4.1.9.9.524.1.2.8 | ScalarcLQd11bVoiceCtrl | read-write | current | When admission control is enabled these parameters can be modified. loadBased - controller will reserve and manage max-bandwidth and roaming-bandwidth based on… |
| 1.3.6.1.4.1.9.9.524.1.2.9 | ScalarcLQd11bExpeditedBw | read-write | current | This object specifies if expedited BW feature is enabled or not. A value of 'true' will ensure that the APs advertise the expedited BW support in their beacons… |
| 1.3.6.1.4.1.9.9.524.1.2.10 | ScalarcLQd11bEdcaProfile | read-write | current | This object represents the EDCA profile to be used in EDCA Parameter set element. See glossary for EDCA. wmmDefault - WMM default standard parameters. svpVoice… |
| 1.3.6.1.4.1.9.9.524.1.2.11 | ScalarcLQd11bMacOptimization | read-write | current | This object represents MAC enhancements for voice, resulting in improvement in number of voice calls serviced per access point. A value of 'true' enables MAC o… |
| 1.3.6.1.4.1.9.9.524.1.2.12 | ScalarcLQd11bMaxCallLimit | read-write | deprecated | This object represents the max number of CAC Voice Calls allowed on dot11b radio band. Value of zero denotes no limit. This mib is deprecated since this config… |
| 1.3.6.1.4.1.9.9.524.1.2.13 | ScalarcLQd11bMcastDirectEnable | read-write | current | This object specifies the decision flag to allow multicast direct stream on radio. This overrides Resource Reservation Control status. |
| 1.3.6.1.4.1.9.9.524.1.2.14 | ScalarcLQd11bBestEffortAdmission | read-write | current | This object specifies whether to admit a media stream in best effort queue. |
| 1.3.6.1.4.1.9.9.524.1.2.15 | ScalarcLQd11bRedirectBestEffort | read-write | current | This object specifies whether a unicast or multicast only video stream can be redirected to best effort. |
| 1.3.6.1.4.1.9.9.524.1.2.16 | ScalarcLQd11bRadioMaxStreams | read-write | current | This object specifies the maximum number of allowed streams per radio for a 802.11b band. |
| 1.3.6.1.4.1.9.9.524.1.2.17 | ScalarcLQd11bMaxVideoATPercent | read-write | current | This object denotes the maximum allowed bandwidth for video traffic. |
| 1.3.6.1.4.1.9.9.524.1.2.18 | ScalarcLQd11bMaxVoiceATPercent | read-write | current | This object denotes the maximum allowed bandwidth for voice traffic. |
| 1.3.6.1.4.1.9.9.524.1.2.19 | ScalarcLQd11bMaxMediaATPercent | read-write | current | This object specifies the maximum allowed bandwidth for media traffic. |
| 1.3.6.1.4.1.9.9.524.1.2.20 | ScalarcLQd11bMinPhyRate | read-write | current | This object specifies the minimum physical rate that should be enabled by a client to successfully join a media stream. |
| 1.3.6.1.4.1.9.9.524.1.2.21 | ScalarcLQd11bClientMaxStreams | read-write | current | This object specifies the maximum number of allowed streams per client for a 802.11b band. |
| 1.3.6.1.4.1.9.9.524.1.2.22 | ScalarcLQd11bSipCacSupportEnable | read-write | current | This object specifies whether SIP CAC is enabled. A value of 'true' enables SIP CAC on dot11b radio band. A value of 'false' disables SIP CAC on dot11b radio b… |
| 1.3.6.1.4.1.9.9.524.1.3 | NodecLQd11GprConfig | |||
| 1.3.6.1.4.1.9.9.524.1.3.1 | TablecLQd11GprTable | not-accessible | current | This table populates the GPR configuration on the WLANs configured on this controller. There exists a row in this table for each WLAN configured through cLWlan… |
| 1.3.6.1.4.1.9.9.524.1.3.1.1 | RowcLQd11GprEntry | not-accessible | current | Each entry represents a conceptual row in cLQd11GprTable and corresponds to the GPR configuration on a WLAN. |
| 1.3.6.1.4.1.9.9.524.1.3.1.1.1 | ColumncLQd11GprSupport | read-write | current | If 'true', then the corresponding radios that advertise this WLAN, will send Gratuitous Probe Response. If 'false', then the corresponding radios that advertis… |
| 1.3.6.1.4.1.9.9.524.1.4 | NodecLQd11CACStats | |||
| 1.3.6.1.4.1.9.9.524.1.4.1 | TablecLQd11CACStatsTable | not-accessible | current | This table populates the call admission control metrics collected by observing the voice or video traffic on the dot11 interface of a particular AP. There exis… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1 | RowcLQd11CACStatsEntry | not-accessible | current | Each entry represents a conceptual row in CLQd11CACStatsTable and corresponds to the admission control statistics for a particular dot11 interface. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.1 | ColumncLQd11CacVoiceBwInUse | read-only | current | This object indicates the voice bandwidth in use as a percentage of the bandwidth configured through cLQd11aVoiceMaxAdmBandwidth or cLQd11bVoiceMaxAdmBandwidth… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.2 | ColumncLQd11CacVideoBwInUse | read-only | current | This object indicates the video bandwidth in use as a percentage of the bandwidth configured through cLQd11aVideoMaxAdmBandwidth or cLQd11bVideoMaxAdmBandwidth… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.3 | ColumncLQd11CacVoiceCallsInProgress | read-only | current | This object indicates the count of the number of voice calls currently in progress on this dot11 interface. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.4 | ColumncLQd11CacRoamVoiceCallsInProg | read-only | current | This object indicates the count of the number of voice calls initiated from roaming clients currently in progress on this dot11 interface. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.5 | ColumncLQd11CacTotalVoiceCallsAP | read-only | current | This object indicates the count of the number of voice calls observed on this dot11 interface ever since this AP has joined the controller. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.6 | ColumncLQd11CacTotalRoamCallsAP | read-only | current | This object indicates the count of the number of voice and video calls initiated from roaming clients observed on this dot11 interface ever since this AP has j… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.7 | ColumncLQd11CacVoiceCallsRejectedAP | read-only | current | This object indicates the count of the number of voice calls observed as rejected on this dot11 interface, ever since this AP has joined the controller. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.8 | ColumncLQd11CacRoamCallsRejectedAP | read-only | current | This object indicates the count of the number of voice and video calls initiated from roaming clients observed as rejected on this dot11 interface, ever since … |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.9 | ColumncLQd11CacRejCallsInsufBw | read-only | current | This object indicates the count of the number of calls observed as rejected on this dot11 interface due to insufficient bandwidth, ever since this AP has joine… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.10 | ColumncLQd11CacRejCallsBadParams | read-only | current | This object indicates the count of the number of calls observed as rejected on this dot11 interface due to mismatch in call parameters, ever since this AP has … |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.11 | ColumncLQd11CacRejCallsPhyRate | read-only | current | This object indicates the count of the number of calls observed as rejected on this dot11 interface due to mismatch in 802.11 data rates, ever since this AP ha… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.12 | ColumncLQd11CacRejCallsQosPolicy | read-only | current | This object indicates the count of the number of calls observed as rejected on this dot11 interface due to restrictions imposed by QOS policies, ever since thi… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.13 | ColumncLQd11SipCacNonRoamCallsInProgress | read-only | current | This object indicates the number of non-roaming SIP calls currently in progress on this dot11 interface. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.14 | ColumncLQd11SipCacRoamCallsInProg | read-only | current | This object indicates the number of SIP calls initiated from roaming clients currently in progress on this dot11 interface. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.15 | ColumncLQd11SipCacTotalNonRoamCallsAP | read-only | current | This object indicates the number of non-roaming SIP calls observed on this dot11 interface since this AP has joined the controller. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.16 | ColumncLQd11SipCacTotalRoamCallsAP | read-only | current | This object indicates the number of SIP calls initiated from roaming clients observed on this dot11 interface ever this AP has joined the controller. |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.17 | ColumncLQd11SipCacNonRoamCallsRejectedInSuffBw | read-only | current | This object indicates the number of non-roaming SIP calls observed as rejected on this dot11 interface due to insufficient bandwidth, since this AP has joined … |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.18 | ColumncLQd11SipCacRoamCallsRejectedInSuffBw | read-only | current | This object indicates the number of SIP calls initiated from roaming clients observed as rejected on this dot11 interface due to insufficient bandwidth, since … |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.19 | ColumncLQd11SipCacNonRoamCallsRejectedMaxLimit | read-only | current | This object indicates the number of non-roaming SIP calls observed as rejected on this dot11 interface due to maximum limit exceeded, since this AP has joined … |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.20 | ColumncLQd11SipCacRoamCallsRejectedMaxLimit | read-only | current | This object indicates the number of roaming SIP calls observed as rejected on this dot11 interface due to maximum limit exceeded, since this AP has joined the … |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.21 | ColumncLQd11SipCacRejCallsQosPolicy | read-only | current | This object indicates the number of SIP calls observed as rejected on this dot11 interface due to restrictions imposed by QOS policies, ever since this AP has … |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.22 | ColumncLQd11SipCacPreferredCallsReceived | read-only | current | This object indicates the number of preferred calls observed as received on this dot11 interface due to restrictions imposed by QOS policies, ever since this A… |
| 1.3.6.1.4.1.9.9.524.1.4.1.1.23 | ColumncLQd11SipCacPreferredCallsAccepted | read-only | current | This object indicates the number of preferred calls observed as accepted on this dot11 interface due to restrictions imposed by QOS policies, ever since this A… |
| 1.3.6.1.4.1.9.9.524.1.5 | NodecLQEntConfConfig | |||
| 1.3.6.1.4.1.9.9.524.1.6 | NodecLQd11VoiceStats | |||
| 1.3.6.1.4.1.9.9.524.1.6.1 | TablecLQd11VoiceStatsTable | not-accessible | current | This table represents the voice statistics calculated for each radio on an AP. An entry is automatically added by the controller when a voice call is successfu… |
| 1.3.6.1.4.1.9.9.524.1.6.1.1 | RowcLQd11VoiceStatsEntry | not-accessible | current | Each entry in this table provides voice related statistics for each radio on an AP. Entries are removed when the AP disassociates the controller. |
| 1.3.6.1.4.1.9.9.524.1.6.1.1.1 | ColumncLQd11VoiceCallCounts | read-only | current | This object indicates cumulative number of successful VOIP calls placed using this radio. |
| 1.3.6.1.4.1.9.9.524.1.6.1.1.2 | ColumncLQd11CacVoiceCallTimePeriod | read-only | current | This object indicates cumulative call proceed time in seconds. |
| 1.3.6.1.4.1.9.9.524.1.7 | NodecLQVoiceWlanConfig | |||
| 1.3.6.1.4.1.9.9.524.1.8 | NodecLQVoiceClient | |||
| 1.3.6.1.4.1.9.9.524.1.8.1 | TablecLQVoiceClientTable | not-accessible | current | This table contains voice related client properties. There exists a row in this table for each associated voice clients. A row is added to this table by the ag… |
| 1.3.6.1.4.1.9.9.524.1.8.1.1 | RowcLQVoiceClientEntry | not-accessible | current | An entry containing voice call management information for a particular client. |
| 1.3.6.1.4.1.9.9.524.1.8.1.1.1 | ColumncLQVoiceClientCallingNumber | read-only | current | This object indicates calling number of this voice client |
| 1.3.6.1.4.1.9.9.524.1.8.1.1.2 | ColumncLQVoiceClientLastCalledNumber | read-only | current | This object indicates last called number from this voice client |
| 1.3.6.1.4.1.9.9.524.1.8.1.1.3 | ColumncLQVoiceClientLastCallFailureReasonCode | read-only | current | This object represents last VOIP failue reason code of this voice client. These reason codes are taken from SIP standards. unknown - Unknown error normalFailur… |
| 1.3.6.1.4.1.9.9.524.1.9 | NodecLQMediaClient | |||
| 1.3.6.1.4.1.9.9.524.1.9.1 | TablecLQMediaClientTable | not-accessible | current | This table represents media related client properties. There exists a row in this table for each associated- media clients. A row is added to this table by the… |
| 1.3.6.1.4.1.9.9.524.1.9.1.1 | RowcLQMediaClientEntry | not-accessible | current | Each entry represents a conceptual row in cLQMediaClientTable and corresponds to media properties of client. There exists a row in this table for each client a… |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.1 | ColumncLQVMediaClientDestIpAddrType | not-accessible | current | This object indicates the type of address specified by the corresponding instance of cLQVMediaClientDestIpAddr. |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.2 | ColumncLQVMediaClientDestIpAddr | not-accessible | current | This object indicates the destination multicast IP address of the associated client. |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.3 | ColumncLQVMediaClientSrcIpAddrType | read-only | current | This object indicates the type of address specified by the corresponding instance of cLQVMediaClientSrcIpAddr. |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.4 | ColumncLQVMediaClientSrcIpAddr | read-only | current | This object specifies the source multicast IP address of the associated client. |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.5 | ColumncLQVMediaClientApMacAddress | read-only | current | This object indicates the MAC address of the AP, the client gets associated during the streaming. |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.6 | ColumncLQVMediaClientWlanIndex | read-only | current | This object indicates the wlan SSID the client uses for associating to the AP on the controller. The value 513-517 indicates wired clients. |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.7 | ColumncLQVMediaClientRadioType | read-only | current | This object indicates the type of radio used by the associated client. |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.8 | ColumncLQVMediaClientQos | read-only | current | This object indicates the QOS policy enforced by the associated client. bestEffort - media stream clients associated to the stream identified by stream name ar… |
| 1.3.6.1.4.1.9.9.524.1.9.1.1.9 | ColumncLQVMediaClientDecision | read-only | current | This object indicates the decision policy that has been used when client gets associated to the media stream. deny - denial of client to the media strem. admit… |
| 1.3.6.1.4.1.9.9.524.1.9.2 | TablecLQMediaClientHistoryTable | not-accessible | current | This table represents media related client properties available during a specific time denoted by cLQVMediaClientHistTimeStamp in history. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1 | RowcLQMediaClientHistoryEntry | not-accessible | current | Each entry represents a conceptual row in cLQMediaClientHistoryTable and corresponds to media related client properties available during a specific time denote… |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.1 | ColumncLQVMediaClientHistTimeStamp | not-accessible | current | This object uniquely identifies one instance of the timestamp in history for which the client admit/deny happened. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.2 | ColumncLQVMediaClientHistClientMacAddress | read-only | current | This object indicates the MAC address of the client for this entry. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.3 | ColumncLQVMediaClientHistApMacAddress | read-only | current | This object indicates the MAC address of the AP, the client gets associated during the streaming. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.4 | ColumncLQVMediaClientHistSlotId | read-only | current | This object indicates the slot identifier of the AP to which the client associates during the streaming. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.5 | ColumncLQVMediaClientHistDestIpAddrType | read-only | current | This object specifies the destination multicast IP address type of the associated client. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.6 | ColumncLQVMediaClientHistDestIpAddr | read-only | current | This object indicates the destination multicast IP address of the associated client. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.7 | ColumncLQVMediaClientHistDecision | read-only | current | This object indicates the decision policy that was used when client gets associated to the media stream. deny - denial of client to the media strem. admit - Ad… |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.8 | ColumncLQVMediaClientHistLastFailureReasonCode | read-only | current | This object indicates last failure reason code of this media client. enoughBw(1) - Radio can handle additional client traffic. Hence, allowing client admission… |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.9 | ColumncLQVMediaClientHistWlanIndex | read-only | current | This object indicates the wlan SSID used by the client to associate to the AP on the controller. The value 513-517 indicates wired clients. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.10 | ColumncLQVMediaClientHistRadioType | read-only | current | This object indicates the type of radio used by the associated client. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.11 | ColumncLQVMediaClientHistQos | read-only | current | This object indicates the QOS policy enforced by the associated client. bestEffort - media stream clients associated to the stream identified by stream name ar… |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.12 | ColumncLQVMediaClientHistCfgBw | read-only | current | This object indicates the configured stream bandwidth of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.13 | ColumncLQVMediaClientHistCurrentRate | read-only | current | This object indicates the rate observed of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.14 | ColumncLQVMediaClientHistVideoPktSize | read-only | current | This object indicates the observed video packet size of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.15 | ColumncLQVMediaClientHistVideoUtil | read-only | current | This object indicates the observed video utilization of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.16 | ColumncLQVMediaClientHistVoiceUtil | read-only | current | This object indicates the observed voice utilization of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.17 | ColumncLQVMediaClientHistChannelUtil | read-only | current | This object indicates the observed channel utilization of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.18 | ColumncLQVMediaClientHistQueueUtil | read-only | current | This object indicates the observed queue utilization of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.19 | ColumncLQVMediaClientHistVideoPps | read-only | current | This object identifies the observed video packets per second on the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.20 | ColumncLQVMediaClientHistVideoDelay | read-only | current | This object indicates the observed Video delay of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.21 | ColumncLQVMediaClientHistPktLossDiscard | read-only | current | This object indicates the observed packet loss discard of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.22 | ColumncLQVMediaClientHistPktLossFail | read-only | current | This object indicates the observed packet loss failure of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.23 | ColumncLQVMediaClientHistNumVideoStreams | read-only | current | This object indicates the observed number of video streams of the media client associated to a media stream. |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.24 | ColumncLQVMediaClientHistCacEnable | read-only | current | This object indicates the observed CAC enable state of the media client associated to a media stream. video(1) - video call admission control enabled. voice(2)… |
| 1.3.6.1.4.1.9.9.524.1.9.2.1.25 | ColumncLQVMediaClientHistStreamName | read-only | current | This object indicates the media stream name to which the client was admitted at the particular timestamp. |
| 1.3.6.1.4.1.9.9.524.1.9.3 | TablecLQMediaMulticastClientTable | not-accessible | current | This table represents media related client properties for multicast clients. There exists a row in this table for each associated media clients. A row is added… |
| 1.3.6.1.4.1.9.9.524.1.9.3.1 | RowcLQMediaMulticastClientEntry | not-accessible | current | Each entry represents a conceptual row in cLQMediaMulticastClientTable and corresponds to media properties of client. |
| 1.3.6.1.4.1.9.9.524.1.9.3.1.1 | ColumncLQVMediaClientMCGrpIpAddrType | not-accessible | current | This object represents multicast destination IP address type. |
| 1.3.6.1.4.1.9.9.524.1.9.3.1.2 | ColumncLQVMediaClientMCGrpIpAddr | not-accessible | current | This object represents multicast destination IP address. |
| 1.3.6.1.4.1.9.9.524.1.9.3.1.3 | ColumncLQVMediaClientVlanId | read-only | current | This object represents the VLAN id of the client. |
| 1.3.6.1.4.1.9.9.524.1.9.3.1.4 | ColumncLQVMediaMCClientApName | read-only | current | This object represents the unique access point to which the multicast client is connected. |
| 1.3.6.1.4.1.9.9.524.1.9.3.1.5 | ColumncLQVMediaClientMCUCStatus | read-only | current | This object represents whether the multicast client has multicast-to-unicast feature enabled. |
| 1.3.6.1.4.1.9.9.524.1.10 | NodecLQd11SipCacConfig | |||
| 1.3.6.1.4.1.9.9.524.1.10.1 | TablecLQd11SipCacConfigTable | not-accessible | current | This table contains the information about the SIP CAC configuration corresponding to the dot11 bands of the APs that have joined the controller. The parameters… |
| 1.3.6.1.4.1.9.9.524.1.10.1.1 | RowcLQd11SipCacConfigEntry | not-accessible | current | An entry containing SIP CAC configuration for a particular type of wireless interface. |
| 1.3.6.1.4.1.9.9.524.1.10.1.1.1 | ColumncLQd11SipCacConfigCodecType | read-write | current | This object specifies the configured codec for SIP Cac configuration of the dot11 band for the APs associated with this controller. Codec determines the bandwi… |
| 1.3.6.1.4.1.9.9.524.1.10.1.1.2 | ColumncLQd11SipCacConfigBw | read-write | current | This object specifies the configured bandwidth in kbps for SIP CAC configuration of the dot11 band for the APs associated with this controller. This is configu… |
| 1.3.6.1.4.1.9.9.524.1.10.1.1.3 | ColumncLQd11SipCacConfigVoiceSampleSize | read-write | current | This object specifies the configured voice sample size in milliseconds for SIP Cac configuration of the dot11 band for the APs associated with this controller. |
| 1.3.6.1.4.1.9.9.524.1.10.1.1.4 | ColumncLQd11SipCacMaxPossibleVoiceCalls | read-only | current | This object represents the maximum possible voice calls that can be made with respect to the current SIP CAC configuration. |
| 1.3.6.1.4.1.9.9.524.1.10.1.1.5 | ColumncLQd11SipCacMaxPossibleReservedRoamingCalls | read-only | current | This object represents the maximum possible reserved roaming calls that can be made with respect to the current SIP CAC configuration. |
| 1.3.6.1.4.1.9.9.524.1.11 | NodecLQMediaStreamConfig | |||
| 1.3.6.1.4.1.9.9.524.1.11.1 | TablecLQMStreamTable | not-accessible | current | This table lists different media streams identified by its name and the stream parameters. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1 | RowcLQMStreamEntry | not-accessible | current | Each entry represents a conceptual row in cLQMStreamTable and corresponds to the media stream configuration on the device. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.1 | ColumncLQMStreamName | not-accessible | current | This object specifies a human readable name which uniquely identifies the media stream. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.2 | ColumncLQMStreamStorageType | read-create | current | This object represnts the storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.3 | ColumncLQMStreamSrcIPAddrType | read-create | current | This object specifies the source Ip multicast address type to be used by the media stream. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.4 | ColumncLQMStreamSrcIPAddr | read-create | current | This object specifies the source Ip multicast address to be used by the media stream. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.5 | ColumncLQMStreamState | read-create | current | This object specifies the current state of the media stream. 'true' - Indicates the media stream state is enabled. 'false' - Indicates the media stream state i… |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.6 | ColumncLQMStreamRrcExpBw | read-create | current | This object specifies Resource Reservation Control(RRC) bandwidth utilization. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.7 | ColumncLQMStreamRrcAvgPkt | read-create | current | This object specifies RRC average packet size. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.8 | ColumncLQMStreamReRrc | read-create | current | This object specifies whether re-RRC calculations are enabled. 'true' - Indicates the calculations are enabled. 'false' - Indicates the calculations are disabl… |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.9 | ColumncLQMStreamRrcQos | read-create | current | This object specifies RRC QOS queue information. bestEffort - media stream clients associated to the stream identified by stream name are scheduled to a best e… |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.10 | ColumncLQMStreamRrcType | read-create | current | This object specifies RRC Media stream type. mc2uc - multicast to unicast enabled. mOnly - only multicast enabled. unicast - unicast enabled. disabled - neithe… |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.11 | ColumncLQMStreamRrcPriority | read-create | current | This object specifies RRC Priority bit set within media stream. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.12 | ColumncLQMStreamRrcViolation | read-create | current | This object specifies the RRC violation policy to be applied when the media stream violates the profile. This object specifies whether to drop the stream or pr… |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.13 | ColumncLQMStreamRrcPolicy | read-create | current | This object specifies whether the media stream should be allowed or denied. true - Allow the media stream. false - Deny the media stream. |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.14 | ColumncLQMStreamDestStartInetAddrType | read-create | current | This object represents Multicast Destination Start Address Type |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.15 | ColumncLQMStreamDestStartInetAddr | read-create | current | This object represents Multicast Destination Start Address |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.16 | ColumncLQMStreamDestEndInetAddrType | read-create | current | This object represents Multicast Destination End Address Type |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.17 | ColumncLQMStreamDestEndInetAddr | read-create | current | This object represents Multicast Destination End Address |
| 1.3.6.1.4.1.9.9.524.1.11.1.1.18 | ColumncLQMStreamRowStatus | read-create | current | This is the status column for this row and used to create and delete specific instances of rows in this table. cLQMStreamName is mandatory for successful creat… |
| 1.3.6.1.4.1.9.9.524.1.11.2 | NodecLQMStreamSdpConfig | |||
| 1.3.6.1.4.1.9.9.524.1.11.2.1 | ScalarcLQMStreamSdpUrl | read-write | current | This object specifies the media stream session description protocol (SDP) URL. While MC2UC request is denied, AP will send session announcement message to the … |
| 1.3.6.1.4.1.9.9.524.1.11.2.2 | ScalarcLQMStreamSdpEmail | read-write | current | This object specifies the media stream session description protocol (SDP) email. While MC2UC request is denied, AP will send session announcement message to cl… |
| 1.3.6.1.4.1.9.9.524.1.11.2.3 | ScalarcLQMStreamSdpPhone | read-write | current | This object specifies the media stream session description protocol (SDP) phone. While MC2UC request is denied, AP will send session announcement message to cl… |
| 1.3.6.1.4.1.9.9.524.1.11.2.4 | ScalarcLQMStreamSdpNote | read-write | current | This object specifies the media stream session description protocol (SDP) note. While MC2UC request is denied, AP will send session announcement message to cli… |
| 1.3.6.1.4.1.9.9.524.1.11.2.5 | ScalarcLQMStreamSdpStatus | read-write | current | This object specifies the media stream session description protocol (SDP) status. While MC2UC request is denied, AP will send session announcement message to c… |
| 1.3.6.1.4.1.9.9.524.1.11.3 | NodecLQMStreamRrcGlobal | |||
| 1.3.6.1.4.1.9.9.524.1.11.3.1 | ScalarcLQMStreamRrcGlobalState | read-write | current | This object specifies the administrative status of media stream functionality in the device. Enable - Enables the media stream functionality. Disable - Disable… |
| 1.3.6.1.4.1.9.9.524.1.12 | NodecLQPreferredCallConfig | |||
| 1.3.6.1.4.1.9.9.524.1.12.1 | TablecLQPreferredCallTable | not-accessible | current | This table populates the preferred call configuration. When the call comes to any of these numbers, even if there is no bandwidth available in the configured v… |
| 1.3.6.1.4.1.9.9.524.1.12.1.1 | RowcLQPreferredCallEntry | not-accessible | current | Each entry represents a conceptual row in cLQPreferredCallTable and corresponds to the preferred call number of the user. |
| 1.3.6.1.4.1.9.9.524.1.12.1.1.1 | ColumncLQPreferredCallIndex | not-accessible | current | This object indicates an arbitrary integer-value that uniquely identifies a preferred call number configured by the user. |
| 1.3.6.1.4.1.9.9.524.1.12.1.1.2 | ColumncLQPreferredCallNumber | read-create | current | This object specifies the preferred call number configured by the user. |
| 1.3.6.1.4.1.9.9.524.1.12.1.1.3 | ColumncLQPreferredCallRowStatus | read-create | current | This is the status column for this row and used to create and delete specific instances of rows in this table. The following objects are mandatory for successf… |
| 1.3.6.1.4.1.9.9.524.1.12.1.1.4 | ColumncLQPreferredCallStorageType | read-create | current | This object specifies the storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.524.1.13 | NodecLQConfigObjects | |||
| 1.3.6.1.4.1.9.9.524.1.13.1 | ScalarciscoLwappVoipCallFailureNotifEnabled | read-write | current | The object to control the generation of ciscoLwappVoipCallFailureNotif notification. A value of 'true' indicates that the agent generates ciscoLwappVoipCallFai… |
| 1.3.6.1.4.1.9.9.524.1.14 | NodecLQoSProfileConfig | |||
| 1.3.6.1.4.1.9.9.524.1.15 | NodecLQoSSipSnoopingConfig | |||
| 1.3.6.1.4.1.9.9.524.1.15.1 | ScalarcLQoSSipSnoopingPortRangeStart | read-write | current | This object specifies the starting port with respect to SIP snooping feature on controller. If single port has to be used, configure cLQoSSipSnoopingPortRangeS… |
| 1.3.6.1.4.1.9.9.524.1.15.2 | ScalarcLQoSSipSnoopingPortRangeEnd | read-write | current | This object specifies the ending port with respect to SIP snooping feature on controller. If single port has to be used, configure cLQoSSipSnoopingPortRangeSta… |
| 1.3.6.1.4.1.9.9.524.1.16 | NodecLQoSAirTimeFairness | |||
| 1.3.6.1.4.1.9.9.524.1.16.1 | TablecLQoSGlobalAirTimeFairnessTable | not-accessible | current | This table is used to configure the global dot11 parameters per slot id, represented by cLApDot11IfSlotId, of the radio interface in all the ATF supported APs … |
| 1.3.6.1.4.1.9.9.524.1.16.1.1 | RowcLQoSGlobalAirTimeFairnessEntry | not-accessible | current | This represents an entry in cLQoSGlobalAirTimeFairnessTable. |
| 1.3.6.1.4.1.9.9.524.1.16.1.1.1 | ColumncLGlobalAirTimeFairnessMode | read-write | current | This object is used to set the mode1 - Disabled 2 - SSID Mode 3 - Monitor Mode represented by cLApDot11IfType of ATF supported APs joined in the controller.Rea… |
| 1.3.6.1.4.1.9.9.524.1.16.1.1.2 | ColumncLGlobalAirTimeFairnessOptimizationPolicy | read-write | current | This object is used to configure the Optimization Policy represented by cLApDot11IfType of ATF supported APs, joined in the controller.Read operation on this a… |
| 1.3.6.1.4.1.9.9.524.1.16.1.1.3 | ColumncLGlobalBridgeClientAccess | read-write | current | This object specifies whether airtime allocation is enabled for the client access node. |
| 1.3.6.1.4.1.9.9.524.1.16.1.1.4 | ColumncLGlobalAirTimeAllocation | read-write | current | This object specifies the percentage for airtime allocation for the client access node. |
| 1.3.6.1.4.1.9.9.524.1.16.2 | TablecLQoSAirTimeFairnessTable | not-accessible | current | This table represents the ATF(Air Time Fairness) configuration Per-AP Per-SlotId & ATF supported APs that join with this controller. |
| 1.3.6.1.4.1.9.9.524.1.16.2.1 | RowcLQoSAirTimeFairnessEntry | not-accessible | current | Each entry contains information of Per-AP, Per-SlotId & ATF supported APs information. |
| 1.3.6.1.4.1.9.9.524.1.16.2.1.1 | ColumncLApAirTimeFairnessMode | read-write | current | This object specifies the mode of all the ATF supported access points 1 - Disabled 2 - SSID Mode 3 - Monitor Mode. |
| 1.3.6.1.4.1.9.9.524.1.16.2.1.2 | ColumncLApAirTimeFairnessOptimizationPolicy | read-write | current | This object specifies StealingPolicy of all the ATF supported access points should be enabled or disabled. |
| 1.3.6.1.4.1.9.9.524.1.16.3 | TablecLQoSAirTimeFairnessWlanStatisticsTable | not-accessible | current | This table represents the ATF(Air Time Fairness) Wlan statistics for each airtime timeslice Per-AP Per-SlotId Per-WlanId of ATF supported APs joined to control… |
| 1.3.6.1.4.1.9.9.524.1.16.3.1 | RowcLQoSAirTimeFairnessWlanStatisticsEntry | not-accessible | current | This entry contains AirTimeFairness TimeSlice Wlan Statistics |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.1 | ColumncLApAirTimeFairnessWlanAirtimeUsedInstantaneous | read-only | current | This object specifies the air time used instantaneous in micro seconds for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.2 | ColumncLApAirTimeFairnessWlanAirtimeUsedCumulative | read-only | current | This object specifies the total AirTime used cumulative for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.3 | ColumncLApAirTimeFairnessWlanBytesSentInstantaneous | read-only | current | This object specifies the number of bytes sent instantaneous for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.4 | ColumncLApAirTimeFairnessWlanBytesSentCumulative | read-only | current | his object specifies the total number of bytes dropped cumulative for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.5 | ColumncLApAirTimeFairnessWlanBytesDroppedInstantaneous | read-only | current | This object specifies the total number of bytes dropped instantaneous for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.6 | ColumncLApAirTimeFairnessWlanBytesDroppedCumulative | read-only | current | This object specifies the total number of bytes dropped cumulative for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.7 | ColumncLApAirTimeFairnessWlanFramesSentInstantaneous | read-only | current | This object specifies the total number of packets sent instantaneous for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.8 | ColumncLApAirTimeFairnessWlanFramesSentCumulative | read-only | current | This object specifies the total number of packets sent cumulative for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.9 | ColumncLApAirTimeFairnessWlanFramesDroppedInstantaneous | read-only | current | This object specifies the total number of packets drop instantaneous for particular AP per Slot per WlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.3.1.10 | ColumncLApAirTimeFairnessWlanFramesDroppedCumulative | read-only | current | This table represents the ATF(Air Time Fairness) Wlan statistics for each airtime timeslice Per-AP Per-SlotId of ATF supported APs joined to controller. |
| 1.3.6.1.4.1.9.9.524.1.16.4 | TablecLQoSAirTimeFairnessStatisticsTable | not-accessible | current | This table represents the ATF(Air Time Fairness) Wlan statistics for each airtime timeslice Per-AP Per-SlotId of ATF supported APs joined to controller. |
| 1.3.6.1.4.1.9.9.524.1.16.4.1 | RowcLQoSAirTimeFairnessStatisticsEntry | not-accessible | current | This entry contains AirTimeFairness TimeSlice Statistics |
| 1.3.6.1.4.1.9.9.524.1.16.4.1.1 | ColumncLApAirTimeFairnessTotalAirtimeUsedInstantaneous | read-only | current | This object specifies the air time used instantaneous in micro seconds for particular AP per Slot. |
| 1.3.6.1.4.1.9.9.524.1.16.4.1.2 | ColumncLApAirTimeFairnessTotalAirtimeUsedCumulative | read-only | current | his object specifies the total AirTime used cumulative for particular AP per Slot. |
| 1.3.6.1.4.1.9.9.524.1.16.4.1.3 | ColumncLApAirTimeFairnessRadioUptime | read-only | current | This object specifies the air time used instantaneous in seconds for particular AP per Slot. |
| 1.3.6.1.4.1.9.9.524.1.16.4.1.4 | ColumncLApAirTimeFairnessRadioUptimeCumulative | read-only | current | This object specifies the total AirTime used cumulative for particular AP per Slot. |
| 1.3.6.1.4.1.9.9.524.1.16.5 | TablecLAPGroupAirTimeFairnessTable | not-accessible | current | This table for configuring the ATF(Air Time Fairness)for AP group. |
| 1.3.6.1.4.1.9.9.524.1.16.5.1 | RowcLAPGroupAirTimeFairnessEntry | not-accessible | current | An entry in cLAPGroupAirTimeFairnessTable for the configuring ATF(Air Time Fairness) for an AP group. |
| 1.3.6.1.4.1.9.9.524.1.16.5.1.1 | ColumncLAPGroupAirTimeFairnessMode | read-write | current | This object represents the ATF(Air Time Fairness) mode for this AP group per radiotype 1 - Disabled 2 - SSID Mode 3 - Monitor Mode. |
| 1.3.6.1.4.1.9.9.524.1.16.5.1.2 | ColumncLAPGroupAirTimeFairnessOptimizationPolicy | read-write | current | This object represents the ATF(Air Time Fairness) StealingPolicy for this AP group per radio type. |
| 1.3.6.1.4.1.9.9.524.1.16.6 | TablecLQosAirTimeFairnessPolicyConfigTable | not-accessible | current | This table represents the AirTimeFairness Policy configuration sent by the controller to the LWAPP APs for their operation. This table doesn't have any depende… |
| 1.3.6.1.4.1.9.9.524.1.16.6.1 | RowcLQosAirTimeFairnessPolicyConfigEntry | not-accessible | current | Each entry in this table represents the Police configuration sent by the controller to LWAPP APs for use during their operations. Entries can be added/deleted … |
| 1.3.6.1.4.1.9.9.524.1.16.6.1.1 | ColumncLAirTimeFairnessPolicyId | not-accessible | current | This object uniquely identifies one instance of a PolicyId on the controller. |
| 1.3.6.1.4.1.9.9.524.1.16.6.1.2 | ColumncLAirTimeFairnessPolicyRowStatus | read-create | current | This is the status column for this row and used to create, modify and delete specific instances of rows in this table. This table supports modification of writ… |
| 1.3.6.1.4.1.9.9.524.1.16.6.1.3 | ColumncLAirTimeFairnessPolicyName | read-create | current | This object represents the profile name assigned to this Policy. The name assigned to a Policy has to be unique across all the Policy on the controller.This ob… |
| 1.3.6.1.4.1.9.9.524.1.16.6.1.4 | ColumncLAirTimeFairnessPolicyWeight | read-create | current | This object represents the Policy Weight assigned to this PolicyId/PolicyName.PolicyId=0 is default policy ID with weight 10. We will not be able to configure/… |
| 1.3.6.1.4.1.9.9.524.1.16.7 | TablecLApAirTimeFairnessPolicyOverrideTable | not-accessible | current | This table represents Per-AP, Per-Radio, Per-WlanId Override of ATF Policy ID on WLAN. |
| 1.3.6.1.4.1.9.9.524.1.16.7.1 | RowcLApAirTimeFairnessPolicyOverrideEntry | not-accessible | current | This entry contains AirTime fairness Policy Id Override on WLAN. |
| 1.3.6.1.4.1.9.9.524.1.16.7.1.1 | ColumncLApAirTimeFairnessPolicyOverride | read-write | current | This object specifies Air time fairness policy override per AP(ATF supported APs) per Radio per WlanProfileName for policy Id assigned to WLAN. |
| 1.3.6.1.4.1.9.9.524.1.16.7.1.2 | ColumncLApAirTimeFairnessOverridePolicyName | read-write | current | his object represents the PolicyName changed for the given WLAN, if cLApAirTimeFairnessPolicyOverride is enabled per AP per slot per wlan profilename. Please n… |
| 1.3.6.1.4.1.9.9.524.1.16.8 | TablecLAPGroupsAirTimeFairnessPolicyOverrideTable | not-accessible | current | This table represents Per-APGroup, Per-WlanId Override of ATF Policy ID on WLAN. |
| 1.3.6.1.4.1.9.9.524.1.16.8.1 | RowcLAPGroupsAirTimeFairnessPolicyOverrideEntry | not-accessible | current | This entry contains AirTime fairness Policy Name Override on APGroup per cLWlanProfileName. |
| 1.3.6.1.4.1.9.9.524.1.16.8.1.1 | ColumncLAPGroupAirTimeFairnessPolicyNameOverrideEnabled | read-write | current | This object represents the per APGroup per Wlan ProfileName level Policy override parameters.If configured as True, user can override the global PolicyName by … |
| 1.3.6.1.4.1.9.9.524.1.16.8.1.2 | ColumncLAPGroupAirTimeFairnessOverridePolicyName | read-write | current | This object represents the PolicyName changed for the given WLAN, if cLAPGroupAirTimeFairnessPolicyNameOverrideEnabled is enabled per AP Group.Please note that… |
| 1.3.6.1.4.1.9.9.524.1.21 | NodecLQd11axCACConfig | |||
| 1.3.6.1.4.1.9.9.524.1.21.1 | ScalarcLQd11axVoiceAdmCtrlSupport | read-write | current | This object is used to enable or disable admission control for voice traffic flowing through the 802.11ax interfaces in the controller. When set to 'true', con… |
| 1.3.6.1.4.1.9.9.524.1.21.2 | ScalarcLQd11axVoiceMaxAdmBandwidth | read-write | current | This object denotes the maximum bandwidth that can be allocated by controller for voice traffic when admission control is enabled for for 802.11ax interfaces i… |
| 1.3.6.1.4.1.9.9.524.1.21.3 | ScalarcLQd11axVoiceMaxRoamBandwidth | read-write | current | This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11axVoiceMaxAdmBandwidth, that can be allocated to roaming cl… |
| 1.3.6.1.4.1.9.9.524.1.21.4 | ScalarcLQd11axVideoAdmCtrlSupport | read-write | current | This object is used to enable or disable admission control for video traffic flowing through the 802.11ax interfaces in the controller. When set to 'true', con… |
| 1.3.6.1.4.1.9.9.524.1.21.5 | ScalarcLQd11axVideoMaxAdmBandwidth | read-write | current | This object denotes the maximum bandwidth that can be allocated by controller for video traffic when admission control is enabled for 802.11ax interfaces in th… |
| 1.3.6.1.4.1.9.9.524.1.21.6 | ScalarcLQd11axVideoMaxRoamBandwidth | read-write | current | This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11aVideoMaxAdmBandwidth, that can be allocated to roaming cli… |
| 1.3.6.1.4.1.9.9.524.1.21.7 | ScalarcLQd11axEdcaProfile | read-write | current | This object specifies the EDCA profile to be used in EDCA Parameter set element. wmmDefault - WMM default standard parameters. svpVoice - Spectralink voice pri… |
| 1.3.6.1.4.1.9.9.524.1.21.8 | ScalarcLQd11axVoiceCtrl | read-write | current | This object specifies the parameters that can be modified, when admission control is enabled. loadBased - controller will reserve and manage max-bandwidth and … |
| 1.3.6.1.4.1.9.9.524.1.21.9 | ScalarcLQd11axExpeditedBw | read-write | current | This object specifies if expedited BW feature is enabled or not. A value of 'true' will ensure that the APs advertise the expedited BW support in their beacons… |
| 1.3.6.1.4.1.9.9.524.1.21.10 | ScalarcLQd11axSipCacSupportEnable | read-write | current | This object specifies whether SIP CAC is enabled. A value of 'true' enables SIP CAC on dot11a radio band. A value of 'false' disables SIP CAC on dot11a radio b… |
| 1.3.6.1.4.1.9.9.524.1.21.11 | ScalarcLQd11axMcastDirectEnable | read-write | current | This object specifies the decision flag to allow multicast direct stream on radio. |
| 1.3.6.1.4.1.9.9.524.1.21.12 | ScalarcLQd11axBestEffortAdmission | read-write | current | This object specifies whether to admit a media stream in best effort queue. |
| 1.3.6.1.4.1.9.9.524.1.21.13 | ScalarcLQd11axRedirectBestEffort | read-write | current | This object specifies whether a unicast or multicast only video stream can be redirected to best effort. |
| 1.3.6.1.4.1.9.9.524.1.21.14 | ScalarcLQd11axRadioMaxStreams | read-write | current | This object specifies the maximum number of allowed streams per radio for a 802.11ax band. |
| 1.3.6.1.4.1.9.9.524.1.21.15 | ScalarcLQd11axMaxMediaATPercent | read-write | current | This object specifies the maximum allowed bandwidth for media traffic. |
| 1.3.6.1.4.1.9.9.524.1.21.16 | ScalarcLQd11axMinPhyRate | read-write | current | This object specifies the minimum physical rate that should be enabled by a client to successfully join a media stream. |
| 1.3.6.1.4.1.9.9.524.1.21.17 | ScalarcLQd11axClientMaxStreams | read-write | current | This object specifies the maximum number of allowed streams per client for a 802.11ax band. |
| 1.3.6.1.4.1.9.9.524.1.22 | NodecLQCacThreshold | |||
| 1.3.6.1.4.1.9.9.524.1.22.1 | NodecLQCacConfigThreshold | |||
| 1.3.6.1.4.1.9.9.524.1.22.1.1 | ScalarcLQCacIPLearnQHighThreshold | read-write | current | This object specifies the high threshold value configured for the Iplearn_Queue. |
| 1.3.6.1.4.1.9.9.524.1.22.1.2 | ScalarcLQCacOutstandingAAAReqQHighThreshold | read-write | current | This object specifies the high threshold value configured for the AAA outstanding request Queue. |
| 1.3.6.1.4.1.9.9.524.1.22.1.3 | ScalarcLQCacIPCHighThreshold | read-write | current | This object specifies high threshold percent configured for the IPC Resources |
| 1.3.6.1.4.1.9.9.524.1.22.1.4 | ScalarcLQCacIPCLowThreshold | read-write | current | This object specifies low threshold percent configured for the IPC Resources |
| 1.3.6.1.4.1.9.9.524.1.22.1.5 | ScalarcLQCacCPUHighThreshold | read-write | current | This object specifies cpu threshold percent configured for the CPU Resources |
| 1.3.6.1.4.1.9.9.524.1.22.1.6 | ScalarcLQCacMobilityDiscoveryQHighThreshold | read-write | current | This object specifies the high threshold value configured for the Mobility_Disovery_Queue. |
| 1.3.6.1.4.1.9.9.524.1.23 | NodecLQCacStats | |||
| 1.3.6.1.4.1.9.9.524.1.23.1 | NodecLQCacStatistics | |||
| 1.3.6.1.4.1.9.9.524.1.23.1.1 | ScalarcLQCacIPLearnQStats | read-only | current | Total Number of CAC throttle due to IP Learn |
| 1.3.6.1.4.1.9.9.524.1.23.1.2 | ScalarcLQCacOutstandingAAAReqQStats | read-only | current | Total Number of CAC throttle due to AAA |
| 1.3.6.1.4.1.9.9.524.1.23.1.3 | ScalarcLQCacIPCHighStats | read-only | current | Total Number of CAC throttle due to IPC |
| 1.3.6.1.4.1.9.9.524.2 | NodeciscoLwappQosMIBConform | |||
| 1.3.6.1.4.1.9.9.524.2.1 | NodeciscoLwappQosMIBCompliances | |||
| 1.3.6.1.4.1.9.9.524.2.1.1 | ComplianceciscoLwappQosMIBCompliance | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappQosMIB module. | |
| 1.3.6.1.4.1.9.9.524.2.1.2 | ComplianceciscoLwappQosMIBComplianceRev1 | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappQosMIB module. | |
| 1.3.6.1.4.1.9.9.524.2.1.3 | ComplianceciscoLwappQosMIBComplianceRev2 | deprecated | Implementation of this group is mandatory only for the platforms which implement the ciscoLwappQosMIB module. | |
| 1.3.6.1.4.1.9.9.524.2.1.4 | ComplianceciscoLwappQosMIBComplianceRev3 | deprecated | Implementation of this group is mandatory only for the platforms which implement the ciscoLwappQosMIB module. | |
| 1.3.6.1.4.1.9.9.524.2.1.5 | ComplianceciscoLwappQosMIBComplianceRev4 | current | Implementation of this group is mandatory only for the platforms which implement the ciscoLwappQosMIB module. | |
| 1.3.6.1.4.1.9.9.524.2.2 | NodeciscoLwappQosMIBGroups | |||
| 1.3.6.1.4.1.9.9.524.2.2.1 | GroupciscoLwappQosDot11aConfigGroup | current | This collection of objects represents the quality-of-service parameters 802.11a networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.2 | GroupciscoLwappQosDot11bConfigGroup | current | This collection of objects represents the quality-of-service parameters 802.11b networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.3 | GroupciscoLwappQosDot11WlanConfigGroup | current | This collection of objects represents the quality-of-services parameters on a particular WLAN. | |
| 1.3.6.1.4.1.9.9.524.2.2.4 | GroupciscoLwappQosDot11CacStatsGroup | current | This collection of objects provide the call admission control statistics observed on the dot11 interfaces of an AP. | |
| 1.3.6.1.4.1.9.9.524.2.2.5 | GroupciscoLwappQosDot11aConfigGroupSup1 | current | This collection of objects represents the quality-of-service parameters 802.11a networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.6 | GroupciscoLwappQosDot11bConfigGroupSup1 | current | This collection of objects represents the quality-of-service parameters 802.11b networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.7 | GroupciscoLwappQosDot11aConfigGroupSup2 | current | This collection of objects represents the quality-of-service parameters 802.11a networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.8 | GroupciscoLwappQosDot11bConfigGroupSup2 | current | This collection of objects represents the quality-of-service parameters 802.11b networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.9 | GroupciscoLwappQosDot11SipCacStatsGroup | current | This collection of objects provide the SIP call admission control statistics observed on the dot11 interfaces of an AP. | |
| 1.3.6.1.4.1.9.9.524.2.2.10 | GroupciscoLwappQosDot11SipConfigGroup | current | This collection of objects represents the SIP call admission control configuration parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.11 | GroupciscoLwappQosDot11VoiceStatsGroup | current | This collection of objects represents the Voice statistics parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.12 | GroupciscoLwappQosDot11VoiceConfigGroup | current | This collection of objects represents the Voice statistics parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.13 | GroupciscoLwappQosDot11VoiceNotifGroup | current | This collection of objects represents the Voice notification parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.14 | GroupciscoLwappQosConfigGroup | current | This collection of objects represents the quality-of-service configuration parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.15 | GroupciscoLwappMediaClientGroup | current | This collection of objects represents the Media client parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.16 | GroupciscoLwappMediaStreamConfigGroup | current | This collection of objects represents the Voice statistics parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.17 | GroupciscoLwappPreferredCallConfigGroup | current | This collection of objects represents the Preferred call config and staistics parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.18 | GroupciscoLwappQosDot11aConfigGroupSup3 | current | This collection of objects represents the quality-of-service parameters 802.11a networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.19 | GroupciscoLwappQosDot11bConfigGroupSup3 | current | This collection of objects represents the quality-of-service parameters 802.11b networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.20 | GroupciscoLwappQosDot11MediaNotifGroup | current | This collection of objects represents the Media notification parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.21 | GroupciscoLwappQosCacConfigGroup | current | This collection ob objects represents the CAC Configured parameters. | |
| 1.3.6.1.4.1.9.9.524.2.2.22 | GroupciscoLwappQosCacStatsGroup | current | This collection ob objects represents the CAC stats. | |
| 1.3.6.1.4.1.9.9.524.2.2.23 | GroupciscoLwappQosDot11axConfigGroup | current | This collection of objects represents the quality-of-service parameters 802.11ax networks. | |
| 1.3.6.1.4.1.9.9.524.2.2.24 | GroupciscoLwappQosDot11axConfigGroupSup3 | current | This collection of objects represents the quality-of-service parameters 802.11ax networks. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CiscoLwappDot11aPhyRates | INTEGER { six(6), nine(9), twelve(12), eighteen(18), twentyFour(24), thirtySix(36), fortyEight(48), fiftyFour(54), sixtyFive(65), seventyTwoPointTwo(72), oneThirty(130), oneThirtyfive(135), oneFortyFourPointFour(144), oneFifty(150), twoSeventy(270), threeHundred(300) } | current | This texual convention denotes the physical rates supported by a 802.11a radio. The rates are indicated in Mbps. |
| CiscoLwappDot11bPhyRates | INTEGER { one(1), two(2), fivePointFive(5), six(6), nine(9), eleven(11), twelve(12), eighteen(18), twentyFour(24), thirtySix(36), fortyEight(48), fiftyFour(54), sixtyFive(65), seventyTwoPointTwo(72), oneThirty(130), oneThirtyFive(135), oneFortyFourPointFour(144), oneFifty(150), twoSeventy(270), threeHundred(300) } | current | This texual convention denotes the physical rates supported by a 802.11b radio. The rates are indicated in Mbps. |