CISCO-VOICE-ATM-DIAL-CONTROL-MIB
54 objects
This MIB module enhances the IETF Dial Control MIB (RFC2128) by providing ATM management information over a data network.
Imported Objects
| CISCO-DIAL-CONTROL-MIB | cCallHistoryIndex |
| CISCO-SMI | ciscoExperiment |
| CISCO-VOICE-COMMON-DIAL-CONTROL-MIB | CvcFaxTransmitRate CvcGUid CvcInBandSignaling CvcSpeechCoderRate |
| DIAL-CONTROL-MIB | callActiveIndex callActiveSetupTime |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.35 | IdentityciscoVoiceAtmDialControlMIB | This MIB module enhances the IETF Dial Control MIB (RFC2128) by providing ATM management information over a data network. | ||
| 1.3.6.1.4.1.9.10.35.1 | NodeciscoVoiceAtmDialControlMIBObjects | |||
| 1.3.6.1.4.1.9.10.35.1.1 | NodecvAtmCallHistory | |||
| 1.3.6.1.4.1.9.10.35.1.1.1 | TablecvAtmCallHistoryTable | not-accessible | current | This table is the ATM extension to the call history table of IETF Dial Control MIB. It contains ATM call leg information about specific voice over ATM call. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1 | RowcvAtmCallHistoryEntry | not-accessible | current | The information regarding a single ATM call leg. An entry of this table is created when its associated call history entry in the IETF Dial Control MIB is creat… |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.1 | ColumncvAtmCallHistoryConnectionId | read-only | current | The global call identifier for the ATM call. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.2 | ColumncvAtmCallHistoryVpi | read-only | current | The VPI used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.3 | ColumncvAtmCallHistoryVci | read-only | current | The VCI used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.4 | ColumncvAtmCallHistoryLowerIfName | read-only | current | The ifName of the ATM interface associated with this call. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.5 | ColumncvAtmCallHistorySessionTarget | read-only | current | The object indicates the session target of the peer that was used for the voice over ATM call. A zero length string indicates that the value is unavailable. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.6 | ColumncvAtmCallHistorySubchannelID | read-only | current | The subchannel used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.7 | ColumncvAtmCallHistorySessionProtocol | read-only | current | Indicates the session protocol used on this call. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.8 | ColumncvAtmCallHistoryCalledNumber | read-only | current | Indicates the called party number for trunk connection calls. A zero length string indicates that this data is unavailable. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.9 | ColumncvAtmCallHistoryDtmfRelay | read-only | current | Indicates if Dtmf Relay was enabled for the call. |
| 1.3.6.1.4.1.9.10.35.1.1.1.1.10 | ColumncvAtmCallHistoryUseSeqNumbers | read-only | current | Indicates if Sequence Numbers were used on the voice data packets. |
| 1.3.6.1.4.1.9.10.35.1.2 | NodecvAtmCallActive | |||
| 1.3.6.1.4.1.9.10.35.1.2.1 | TablecvAtmCallActiveTable | not-accessible | current | This table is the ATM extension to the active call table of IETF Dial Control MIB. It contains ATM call leg information about specific voice over ATM call. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1 | RowcvAtmCallActiveEntry | not-accessible | current | The information regarding a single ATM call leg. An entry of this table is created when its associated call active entry in the IETF Dial Control MIB is create… |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.1 | ColumncvAtmCallActiveConnectionId | read-only | current | The global call identifier for the ATM call. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.2 | ColumncvAtmCallActiveVpi | read-only | current | The VPI used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.3 | ColumncvAtmCallActiveVci | read-only | current | The VCI used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.4 | ColumncvAtmCallActiveLowerIfName | read-only | current | The ifName of the ATM interface associated with this call. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.5 | ColumncvAtmCallActiveSessionTarget | read-only | current | The object indicates the session target of the peer that is used for the voice over ATM call. A null string indicates that the value is unavailable. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.6 | ColumncvAtmCallActiveSubchannelID | read-only | current | The subchannel used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.7 | ColumncvAtmCallActiveSessionProtocol | read-only | current | Indicates the session protocol being used on this call. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.8 | ColumncvAtmCallActiveCalledNumber | read-only | current | Indicates the called party number for trunk connection calls. A null string indicates that this data is unavailable. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.9 | ColumncvAtmCallActiveDtmfRelay | read-only | current | Indicates if Dtmf Relay is enabled for the call. |
| 1.3.6.1.4.1.9.10.35.1.2.1.1.10 | ColumncvAtmCallActiveUseSeqNumbers | read-only | current | Indicates if Sequence Numbers are used on the voice data packets. |
| 1.3.6.1.4.1.9.10.35.1.3 | NodecvAtmDialPeer | |||
| 1.3.6.1.4.1.9.10.35.1.3.1 | TablecvAtmPeerCfgTable | not-accessible | current | The table contains the Voice over ATM (ATM) peer specific information that is required to accept or place voice calls via the ATM backbone with the session pro… |
| 1.3.6.1.4.1.9.10.35.1.3.1.1 | RowcvAtmPeerCfgEntry | not-accessible | current | A single ATM specific Peer. One entry per ATM encapsulation. The entry is created when its associated 'voiceOverATM(152)' encapsulation ifEntry is created. Thi… |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.1 | ColumncvAtmPeerCfgSessionProtocol | read-write | current | The object specifies the session protocol to be used for Internet call between local and remote router via ATM backbone. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.2 | ColumncvAtmPeerCfgInterfaceName | read-write | current | The object specifies the ifName on which the call will go out. A zero length string indicates that no interface has been assigned. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.3 | ColumncvAtmPeerCfgVpi | read-write | current | The VPI used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.4 | ColumncvAtmPeerCfgVci | read-write | current | The VCI used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.5 | ColumncvAtmPeerCfgVcName | read-write | current | The VC Name used for this ATM connection. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.6 | ColumncvAtmPeerCfgCoderRate | read-write | current | This object specifies the default voice coder rate of speech for the ATM peer. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.7 | ColumncvAtmPeerCfgCodecBytes | read-write | current | This object specifies the payload size for the voice packets to be transmitted during the call. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.8 | ColumncvAtmPeerCfgFaxRate | read-write | current | This object specifies the default transmit rate of FAX for the ATM peer. If the value of this object is 'none', then the Fax relay feature is disabled; otherwi… |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.9 | ColumncvAtmPeerCfgFaxBytes | read-write | current | This object specifies the payload size for the fax packets to be transmitted during the call. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.10 | ColumncvAtmPeerCfgInBandSignaling | read-write | current | This object specifies the type of in-band signaling used between the two end points of the call and is used by the router to determine how to interpret the ABC… |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.11 | ColumncvAtmPeerCfgVADEnable | read-write | current | This object specifies whether or not VAD (Voice Activity Detection) is enabled. If the object value is 'false', then the voice data is continuously transmitted… |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.12 | ColumncvAtmPeerCfgUseSeqNumbers | read-write | current | This object specifies whether or not Sequence Numbers are generated on voice packets. |
| 1.3.6.1.4.1.9.10.35.1.3.1.1.13 | ColumncvAtmPeerCfgDtmfRelay | read-write | current | This object specifies whether or not Dtmf Relay is enabled. If it is then dtmf digits are transported as FRF11 Annex C packets, instead of being encoded as spe… |
| 1.3.6.1.4.1.9.10.35.2 | NodeciscoVoiceAtmDialControlMIBNotificationPrefix | |||
| 1.3.6.1.4.1.9.10.35.2.0 | NodeciscoVoiceAtmDialControlMIBNotifications | |||
| 1.3.6.1.4.1.9.10.35.3 | NodeciscoVoiceAtmDialControlMIBConformance | |||
| 1.3.6.1.4.1.9.10.35.3.1 | NodeciscoVoiceAtmDialControlMIBCompliances | |||
| 1.3.6.1.4.1.9.10.35.3.1.1 | ComplianceciscoVoiceAtmDialControlMIBCompliance | read-only | current | The compliance statement for entities which implement the CISCO VOICE ATM DIAL CONTROL MIB |
| 1.3.6.1.4.1.9.10.35.3.2 | NodeciscoVoiceAtmDialControlMIBGroups | |||
| 1.3.6.1.4.1.9.10.35.3.2.1 | GroupcvAtmCallHistoryGroup | current | A collection of objects providing the ATM Call History entry capability. | |
| 1.3.6.1.4.1.9.10.35.3.2.2 | GroupcvAtmCallActiveGroup | current | A collection of objects providing the ATM Call Active entry capability. | |
| 1.3.6.1.4.1.9.10.35.3.2.3 | GroupcvAtmPeerCfgGroup | current | A collection of objects providing the ATM Dialpeer capability. These objects have been implemented as read-only. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CvAtmSessionProtocol | INTEGER { other (1), ciscoSwitched (2), aal2Trunk (3) } | current | Represents a Session Protocol used by Voice calls between a local and remote router via the ATM backbone. other - none of the following. ciscoSwitched - cisco proprietary ATM session protocol. |