DSMPLS-LDP-LSR-PW-MIB
49 objects
Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for the 'Multiprotocol Label Switching, Label Distribution Protocol, LDP' document.
Imported Objects
| DASAN-SMI | dasanEvents dasanMgmt dasanModules |
| DASAN-SWITCH-MIB | dasanSwitchMIBObjects dsSwitchModules |
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress |
| MPLS-LSR-STD-MIB | mplsInterfaceIndex |
| PW-STD-MIB | pwIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 mib-2 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowPointer RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6296.9.1.1.2.28 | IdentitydsMplsLdpStdMIB | Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: … | ||
| 1.3.6.1.4.1.6296.9.1.1.2.28.0 | NodedsMplsLdpLsrNotifications | |||
| 1.3.6.1.4.1.6296.9.1.1.2.28.1 | NodedsMplsLdpLsrObjects | |||
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1 | NodedsMplsLdpObjects | |||
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.1 | ScalardsMplsLdpRouterLdp | read-write | current | This Object is used to perform any LDP operations. Without this object, the Lsr can not perform any LDP operations such as sending Ldp hello packets. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.2 | ScalardsMplsLdpControlMode | read-write | current | The lable processing can be set by using this object. The control mode can be set as either ordered or independent. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.3 | ScalardsMplsLdpExplicitNull | read-write | current | This object is used to configure the router to send explicit-null labels for directly connected FECs instead of implicit-null labels. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.4 | ScalardsMplsLdpGlobalMergeCapability | read-write | current | The merge capability aggregates multiple incoming flows with the same destination address into a single outgoing flow. This reduces the label-space shortage by… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.5 | ScalardsMplsLdpHelloInterval | read-write | current | This object is used to set the interval after which hello packets are sent out. The unit of hello interval value is in seconds |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.6 | ScalardsMplsLdpKeepAliveInterval | read-write | current | This object is used to set the global value of the interval after which keep-alive packets are sent out. The unit of keep alive interval value is in seconds |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.7 | ScalardsMplsLdpMulticastHellos | read-write | current | This object enables multicast hello exchange on all interfaces enabled for LDP. This is used for auto-discovery of LDP peers on directly connected networks. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.8 | ScalardsMplsLdpPwStatusTlv | read-write | current | This object enables the use of the PW Status TLV to signal the pseudowire status. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.9 | ScalardsMplsLdpRequestRetry | read-write | current | This object enables the retry of requests, once a request for a label has been rejected for a valid reason. The LSR to send a maximum of five label requests if… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.10 | ScalardsMplsLdpRequestRetryTimeout | read-write | current | This object is used to set the value for the interval between retries. Before this time is over, a request is re-sent to a peer. The unit of request retry time… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.11 | ScalardsMplsLdpRouterId | read-write | current | This object is used to set the router-id to the supplied IP address. The router uses this address to generate the LDP-ID. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.12 | ScalardsMplsLdpTargetedPeerHelloInterval | read-write | current | This object is used to set the interval for sending unicast hello packets to targeted peers. The unit of targeted peer hello interval value is in seconds |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.13 | ScalardsMplsLdpTargetedPeerHoldTime | read-write | current | The time that the router waits before rejecting an adjacency with targeted peers. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.14 | ScalardsMplsLdpPropagateRelease | read-write | current | This is used to propagate the release of labels to downstream routers. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15 | TabledsMplsLdpInterfaceConfigTable | not-accessible | current | This table contains the information of LDP configuration specific to an interface in the Label Switching Router (LSR) or Label Edge Router (LER). |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1 | RowdsMplsLdpInterfaceConfEntry | not-accessible | current | An entry in this table represents an infromation of LDP configuration parameters which are specific to an interface in the LSR(Label Switching Router). An entr… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.1 | ColumndsMplsLdpInterfaceIndex | not-accessible | current | This specifies the index for the LDP Interface. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.2 | ColumndsMplsLdpInterfacefEnaLdp | read-write | current | This is used to enable/disable LDP on a specified interface. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.3 | ColumndsMplsLdpInterfaceAdvtMode | read-write | current | This is used to set the label advertisement mode for an interface for the current LSR to either downstream-on-demand (label is sent only when requested) or dow… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.4 | ColumndsMplsLdpInterfaceRetentionMode | read-write | current | This is used to set the label retention mode to be used for all labels exchanged via the given interface to either conservative (delete unused labels and FEC) … |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.5 | ColumndsMplsLdpInterfaceHelloInterval | read-write | current | This is used to set the interval for sending multicast hello packets via an interface. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.6 | ColumndsMplsLdpInterfaceHoldTime | read-write | current | This is used to set the hold-time value after which the LSR rejects adjacencies.This is an interface specific command and overrides the value set for an LSR us… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.7 | ColumndsMplsLdpInterfaceKeepAliveInterval | read-write | current | This is used to set the interval for sending keep-alive messages to the peer inorder to maintain a session.Each LSR must send keep-alive messages at regular in… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.8 | ColumndsMplsLdpInterfaceKeepAliveTimeOut | read-write | current | This is used to set the keep-alive time-out value for rejecting a session with the peer. This sets the time period for which an LSR must wait for successive ke… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.9 | ColumndsMplsLdpInterfaceMulticastHello | read-write | current | This is used to enable multicast hello exchange on a specified interface. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.10 | ColumndsMplsLdpInterfaceTargetPeerHelloInt | read-write | current | This is used to set an interval for sending unicast hello packets to targeted-peers via the interface. The targeted-hello is sent to the specific address. The … |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.15.1.11 | ColumndsMplsLdpInterfaceTargetPeerHoldTime | read-write | current | This is used to set the time-out value that is the time that the router waits before rejecting an adjacency with the targeted-peer. The timer is reset everytim… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.16 | TabledsMplsLdpAdvtLabelTable | not-accessible | current | This table contains the information of controlling the LDP label advertisement by prefix acl and peer acl. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.16.1 | RowdsMplsLdpAdvtLabelEntry | not-accessible | current | An entry in this table represents an infromation of LDP label advertisement for prefix acl and peer acl. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.16.1.1 | ColumndsMplsLdpPrefixAcl | read-only | current | Prefix Access Control List is defined as destinations which have their labels advertised. The value of this object may 'any' or the access list name. In this o… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.16.1.2 | ColumndsMplsLdpPeerAcl | read-only | current | Peer acl is defined as LDP neighbors which receives the label advertisements. The value of this object may 'none' or access list name. The string value of the … |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.1.16.1.3 | ColumndsMplsLdpAdvertLabelRowStatus | read-create | current | This object is used to create, modify and delete an entry in this table. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.2 | NodedsMplsLsrObjects | |||
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.2.1 | ScalardsMplsLsrIngressTTL | read-write | current | This object is set to specify a Time to Live (TTL) value for LSPs for which this LSR is the ingress. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.2.2 | ScalardsMplsLsrPropogateTTL | read-write | current | This object is used to enable TTL propagation. Enabling TTL propagation causes the TTL value in the IP header to be copied onto the TTL field in the shim heade… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.2.3 | TabledsMplsLsrInterfaceTable | not-accessible | current | This table specifies per-interface MPLS capability and associated information. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.2.3.1 | RowdsMplsLsrInterfaceEntry | not-accessible | current | An entry in this table represents an information about the label switching. An entry can be created by a network administrator or by an SNMP agent. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.2.3.1.1 | ColumndsMplsLsrLabelSwitching | read-write | current | This is used to enable Label-Switching in the NSM for the specified interface. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.2.3.1.2 | ColumndsMplsLsrLabelSpace | read-write | current | This is used to specify the label space value when the label-switching is enabled for the specified interface. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.3 | NodedsMplsPwObjects | |||
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.3.1 | TabledsMplsPwTable | not-accessible | current | This table specifies information for configuring and status monitoring which are common to all service types and PSN types. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.3.1.1 | RowdsMplsPwEntry | not-accessible | current | An entry in this table represents an information about the PW Group NAme. An entry can be created by a network administrator or by an SNMP agent. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.3.1.1.1 | ColumndsMplsPwGroupName | read-create | current | Specifies a group to which this MPLS Layer-2 virtual circuit belongs. |
| 1.3.6.1.4.1.6296.9.1.1.2.28.1.3.1.1.2 | ColumndsMplsPwCCType | read-create | current | This variable indicates the CC type for VCCV negotiation. The CC type shall be control word (0x01) or router alert label (0x02) or pw-ttl (0x04) or combination… |
| 1.3.6.1.4.1.6296.9.1.1.2.28.2 | NodedsMplsLdpLsrConformance |