HUAWEI-MPLS-EXTEND-MIB
287 objects
This MIB is used for defining the HUAWEI private extended Multiprotocol Label Switching (MPLS) MIB object. All MIB objects are used to describe private managed objects and trap definitions for MPLS.
Imported Objects
| HUAWEI-MIB | hwDatacomm |
| IF-MIB | ifIndex ifName |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| MPLS-LSR-STD-MIB | MplsIndexType |
| MPLS-TC-STD-MIB | MplsExtendedTunnelId MplsLsrIdentifier MplsTunnelIndex MplsTunnelInstanceIndex |
| MPLS-TE-STD-MIB | mplsTunnelAdminStatus mplsTunnelOperStatus |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | BITS Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.5.25.121 | IdentityhwMplsExtendMib | This MIB is used for defining the HUAWEI private extended Multiprotocol Label Switching (MPLS) MIB object. All MIB objects are used to describe private managed… | ||
| 1.3.6.1.4.1.2011.5.25.121.1 | NodehwMplsExtendMibTunnel | |||
| 1.3.6.1.4.1.2011.5.25.121.1.1 | TablehwMplsTunnelTable | not-accessible | current | A tunnel needs to be uniquely identified across an MPLS network. Indexes hwMplsTunnelIndex and hwMplsTunnelInstance uniquely identify a tunnel on the LSR origi… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1 | RowhwMplsTunnelEntry | not-accessible | current | A tunnel needs to be uniquely identified across an MPLS network. Indexes hwMplsTunnelIndex and hwMplsTunnelInstance uniquely identify a tunnel on the LSR origi… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.1 | ColumnhwMplsTunnelIndex | not-accessible | current | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. When the MPLS signalling protocol is rsvp(2), this value equals to the… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.2 | ColumnhwMplsTunnelInstance | not-accessible | current | Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is used to identify multiple instances of tunnels for backu… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.3 | ColumnhwMplsTunnelIngressLSRId | not-accessible | current | Indicates the ingress LSR ID of this tunnel. When the MPLS signalling protocol is rsvp(2), this value equals to the Tunnel Sender Address in the Sender Templat… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.4 | ColumnhwMplsTunnelEgressLSRId | not-accessible | current | Indicates the egress LSR ID of this tunnel. Reference to MPLS-TE-STD-MIB. |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.5 | ColumnhwMplsTunnelClassType | read-only | current | Indicates the bandwidth type used by this tunnel. Options: 1. bc0(1) -indicates the bandwidth type is bc0. 2. bc1(2) -indicates the bandwidth type is bc1. 3. i… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.6 | ColumnhwMplsTunnelBandwidth | read-only | current | Indicates the bandwidth used by this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.7 | ColumnhwMplsTunnelAdminStatus | read-only | current | Indicates the management status of this tunnel.Reference to MPLS-TE-STD-MIB. Options: 1. up(1) -indicates the management status of this tunnel is up. 2. down(2… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.8 | ColumnhwMplsTunnelOperStatus | read-only | current | Indicates the actual operational status of this tunnel, which is but not limited to the status of this tunnel of a certain period.Reference to MPLS-TE-STD-MIB.… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.9 | ColumnhwMplsTunnelSessionAttr | read-only | current | Indicates protection types desired by the primary tunnel, such as node protection, link protection or bandwidth protection. Options: 1. localProtectionDesired(… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.10 | ColumnhwMplsTunnelFrrSetupPrio | read-only | current | Indicates the setup PRI of auto-bypass tunnel. Range: 0-7 Default: 7 |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.11 | ColumnhwMplsTunnelFrrHoldingPrio | read-only | current | Indicates the holding PRI of auto-bypass tunnel. Range: 0-7 Default: 7 |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.12 | ColumnhwMplsTunnelFrrBandwidth | read-only | current | Indicates the protecting bandwidth of auto-bypass tunnel. Its value is defined by the configuration on the primary tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.13 | ColumnhwMplsTunnelFrrSwitchover | read-only | current | Indicates FRR switching times |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.14 | ColumnhwMplsTunnelFrrBypassTableIndex | read-only | current | Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. The bypass table shows interfaces protected by specified bypass tunne… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.15 | ColumnhwMplsTunnelFrrARHopTableIndex | read-only | current | Indicates the table index of the protection type adopted by each hop of the primary tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.16 | ColumnhwMplsTunnelName | read-only | current | Indicates the tunnel name. The name can refer to the tunnel on the console port of the LSR. If mplsTunnelIsIf is set to True, the IfName of the interface corre… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.17 | ColumnhwMplsTunnelIfIndex | read-only | current | Indicates the interface index of the tunnel. It uniquely identifies the tunnel name. |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.18 | ColumnhwMplsTunnelPreBandwidth | read-only | current | Indicates the original bandwidth of the tunnel when the tunnel is in the Modify state. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.19 | ColumnhwMplsTunnelNextBandwidth | read-only | current | Indicates the bandwidth of the tunnel that is to be changed when the tunnel is in the Modify state. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.20 | ColumnhwMplsTunnelCt0Bandwidth | read-only | current | The bandwidth of Class-Type 0 (CT0) in this tunnel, in kbit/s. If all CT bandwidths are 0s, it means that this tunnel's Class-Type is CT0, and bandwidth is 0 k… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.21 | ColumnhwMplsTunnelCt1Bandwidth | read-only | current | The bandwidth of Class-Type 1 (CT1) in this tunnel, in kbit/s. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.22 | ColumnhwMplsTunnelCt2Bandwidth | read-only | current | The bandwidth of Class-Type 2 (CT2) in this tunnel, in kbit/s. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.23 | ColumnhwMplsTunnelCt3Bandwidth | read-only | current | The bandwidth of Class-Type 3 (CT3) in this tunnel, in kbit/s. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.24 | ColumnhwMplsTunnelCt4Bandwidth | read-only | current | The bandwidth of Class-Type 4 (CT4) in this tunnel, in kbit/s. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.25 | ColumnhwMplsTunnelCt5Bandwidth | read-only | current | The bandwidth of Class-Type 5 (CT5) in this tunnel, in kbit/s. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.26 | ColumnhwMplsTunnelCt6Bandwidth | read-only | current | The bandwidth of Class-Type 6 (CT6) in this tunnel, in kbit/s. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.27 | ColumnhwMplsTunnelCt7Bandwidth | read-only | current | The bandwidth of Class-Type 7 (CT7) in this tunnel, in kbit/s. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.28 | ColumnhwMplsTunnelLspType | read-only | current | This object is meaningful only at the ingress of the tunnel. It indicates LSP types. Options: 0. invalid(0) -indicates that the LSP type is invalid, the possib… |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.29 | ColumnhwMplsTunnelInterfaceName | read-only | current | Indicates the tunnel interface name. The object is only valid at the ingress. |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.30 | ColumnhwMplsTunnelSignalProto | read-only | current | Indicates the signal protocol of this tunnel |
| 1.3.6.1.4.1.2011.5.25.121.1.1.1.31 | ColumnhwMplsTunnelType | read-only | current | This object is meaningful only at the ingress of the tunnel. It indicates tunnel types. Options: 1. invalid(1) -indicates that the tunnel type is invalid, the … |
| 1.3.6.1.4.1.2011.5.25.121.1.2 | TablehwTunnelFrrBypassTable | not-accessible | current | Indicates the bypass tunnel. The indexes of this table are hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex. |
| 1.3.6.1.4.1.2011.5.25.121.1.2.1 | RowhwTunnelFrrBypassEntry | not-accessible | current | Indicates the bypass tunnel.The indexes of this entry are hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex. |
| 1.3.6.1.4.1.2011.5.25.121.1.2.1.1 | ColumnhwTunnelFrrBypassListIndex | not-accessible | current | Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.1.2.1.2 | ColumnhwTunnelFrrBypassIndex | not-accessible | current | Indicates the index of the bypass tunnel interface. |
| 1.3.6.1.4.1.2011.5.25.121.1.2.1.3 | ColumnhwTunnelFrrBypassProtIfIndex | read-only | current | Indicates the index of the interface protected by the bypass tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.1.3 | TablehwTunnelFrrARHopTable | not-accessible | current | Indicates the FrrARHopTable, which will show every hop's frr protect information of the tunnel. The indexes of this table are hwTunnelFrrARHopListIndex and hwT… |
| 1.3.6.1.4.1.2011.5.25.121.1.3.1 | RowhwTunnelFrrARHopEntry | not-accessible | current | Indicates the FrrARHopTable, which will show every hop's frr protect information of the tunnel. The indexes of this entry are hwTunnelFrrARHopListIndex and hwT… |
| 1.3.6.1.4.1.2011.5.25.121.1.3.1.1 | ColumnhwTunnelFrrARHopListIndex | not-accessible | current | Indicates the table index of each hop along the primary tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.1.3.1.2 | ColumnhwTunnelFrrARHopIndex | not-accessible | current | Indicates the index of each hop along the primary tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.1.3.1.3 | ColumnhwTunnelFrrARHopProtDesired | read-only | current | Indicates the FRR protection types desired by the primary tunnel interface, including: 0: link protection, 1: node protection, 2: bandwidth protection |
| 1.3.6.1.4.1.2011.5.25.121.1.3.1.4 | ColumnhwTunnelFrrARHopProtActual | read-only | current | Indicates the actual FRR protection types of the primary tunnel interface, including: 0: link protection, 1: node protection, 2: bandwidth protection, 3: prima… |
| 1.3.6.1.4.1.2011.5.25.121.1.4 | TablehwTunnelFrrRouteDBTable | not-accessible | current | Indicates the primary tunnel is protected by which bypass tunnel. The indexes of this table are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance… |
| 1.3.6.1.4.1.2011.5.25.121.1.4.1 | RowhwTunnelFrrRouteDBEntry | not-accessible | current | Indicates the primary tunnel is protected by which bypass tunnel. The indexes of this entry are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance… |
| 1.3.6.1.4.1.2011.5.25.121.1.4.1.1 | ColumnhwTunnelFrrRouteDBTunnelIndex | not-accessible | current | Identifies the index of the primary. Manager obtains new index values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signaling pr… |
| 1.3.6.1.4.1.2011.5.25.121.1.4.1.2 | ColumnhwTunnelFrrRouteDBTunnelInstance | not-accessible | current | Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is the object identifies multiple instances of tunnels for … |
| 1.3.6.1.4.1.2011.5.25.121.1.4.1.3 | ColumnhwTunnelFrrRouteDBTunnelIngressLSRId | not-accessible | current | Identifies the ingress LSR ID of the primary tunnel. When the MPLS signalling protocol is rsvp(2),LSR ID equals to the Tunnel Sender Address in the Sender Temp… |
| 1.3.6.1.4.1.2011.5.25.121.1.4.1.4 | ColumnhwTunnelFrrRouteDBTunnelEngressLSRId | not-accessible | current | Identifies the egress LSR ID of the primary tunnel. Reference to MPLS-TE-STD-MIB. |
| 1.3.6.1.4.1.2011.5.25.121.1.4.1.5 | ColumnhwTunnelFrrRouteDBBypassIfIndex | read-only | current | Indicates the interface index of the bypass tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.1.4.1.6 | ColumnhwTunnelFrrRouteDBInnerLabel | read-only | current | Indicates the inner label of the primary tunnel and bypass tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.1.5 | TablehwStaticLspTable | not-accessible | current | A static LSP is created by a network administrator by using static MPLS. Note that only point-to-point static LSP segments are supported. Each static MPLS LSP … |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1 | RowhwStaticLspEntry | not-accessible | current | A static LSP is created by a network administrator by using static MPLS. Note that only point-to-point static LSP segments are supported. Each static MPLS LSP … |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.1 | ColumnhwStaticLspIndex | not-accessible | current | Indicates the index of the static LSP. If the string is 0x00, it means that the index is invalid. |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.2 | ColumnhwStaticLspInSegmentIndex | not-accessible | current | Indicates the incoming label index of the static LSP/CR-LSP. If the string is 0x00, it means that the index is invalid. In this case, no corresponding mplsInSe… |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.3 | ColumnhwStaticLspOutSegmentIndex | not-accessible | current | Indicates the outgoing index of the static LSP/CR-LSP. If the entry is used to identify the incoming node or intermediate node of the LSP, this object cannot b… |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.4 | ColumnhwStaticLspOwner | read-only | current | Denotes the entity that creates and manages the static LSP. See MPLS-LSR-STD-MIB. Options: 1. static(1) -indicates the static LSP. 2. crstatic(2) -indicates th… |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.5 | ColumnhwStaticLspName | read-only | current | Indicates the name of the static LSP or CR-LSP. The name is appointed when the static LSP or CR-LSP is created. |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.6 | ColumnhwStaticLspStatus | read-only | current | Indicates the actual operation status of the static LSP/CR-LSP. Options: 1. up(1) -indicates that the static LSP/CR-LSP is in Up state. 2. down(2) -indicates t… |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.7 | ColumnhwStaticLspClassType | read-only | current | The Class-Type of this static lsp. Options: 1. ct0(1) -indicates that the class type is ct0. 2. ct1(2) -indicates that the class type is ct1. 3. ct2(3) -indica… |
| 1.3.6.1.4.1.2011.5.25.121.1.5.1.8 | ColumnhwStaticLspBandwidth | read-only | current | The bandwidth of this static lsp. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.6 | TablehwMplsTeClassTable | not-accessible | current | TE-class mapping is a set of a maximum of eight TE-class items. TE-class is a <Class-Type, Priority> pair, such as TE-Class[1] = <CT0, 5>. A (setup/holding) pr… |
| 1.3.6.1.4.1.2011.5.25.121.1.6.1 | RowhwMplsTeClassEntry | not-accessible | current | TE-class mapping is a set of a maximum of eight TE-class items. TE-class is a <Class-Type, Priority> pair, such as TE-Class[1] = <CT0, 5>. A (setup/holding) pr… |
| 1.3.6.1.4.1.2011.5.25.121.1.6.1.1 | ColumnhwMplsTeClassId | not-accessible | current | This value represents the index of the TE-Class configured on this LSR. |
| 1.3.6.1.4.1.2011.5.25.121.1.6.1.2 | ColumnhwMplsTeClassClassType | read-only | current | This value represents a Class-Type supported on the LSR. Options: 1. ct0(1) -indicates that the class type of static CR-LSP is ct0. 2. ct1(2) -indicates that t… |
| 1.3.6.1.4.1.2011.5.25.121.1.6.1.3 | ColumnhwMplsTeClassPriority | read-only | current | This value represents the preemption priority (setup or holding) supported for a particular class-type, on the LSR. Range: 0-7 Default: 7 |
| 1.3.6.1.4.1.2011.5.25.121.1.6.1.4 | ColumnhwMplsTeClassDescription | read-only | current | Textual description of the TE-Class defined by this row. |
| 1.3.6.1.4.1.2011.5.25.121.1.7 | TablehwMplsIfBcTable | not-accessible | current | This table describes bandwidth constraints associated with MPLS TE enabled interfaces. The index of this table is ifIndex. |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1 | RowhwMplsIfBcEntry | not-accessible | current | This table describes bandwidth constraints associated with MPLS TE enabled interfaces. The index of this entry is ifIndex. |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.1 | ColumnhwMplsIfMaxResvBandwidth | read-only | current | The maximum reservable bandwidth on this interface. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.2 | ColumnhwMplsIfBc0Bandwidth | read-only | current | The bandwidth of Class-Type 0 (CT0) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.3 | ColumnhwMplsIfBc1Bandwidth | read-only | current | The bandwidth of Class-Type 1 (CT1) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.4 | ColumnhwMplsIfBc2Bandwidth | read-only | current | The bandwidth of Class-Type 2 (CT2) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.5 | ColumnhwMplsIfBc3Bandwidth | read-only | current | The bandwidth of Class-Type 3 (CT3) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.6 | ColumnhwMplsIfBc4Bandwidth | read-only | current | The bandwidth of Class-Type 4 (CT4) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.7 | ColumnhwMplsIfBc5Bandwidth | read-only | current | The bandwidth of Class-Type 5 (CT5) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.8 | ColumnhwMplsIfBc6Bandwidth | read-only | current | The bandwidth of Class-Type 6 (CT6) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.7.1.9 | ColumnhwMplsIfBc7Bandwidth | read-only | current | The bandwidth of Class-Type 7 (CT7) in this tunnel. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.8 | TablehwStaticLspTnlTable | not-accessible | current | hwStaticLspTnlTable is used to display static LSP token of a static LSP of a specified name. The index of this table is hwStaticLspTnlName. |
| 1.3.6.1.4.1.2011.5.25.121.1.8.1 | RowhwStaticLspTnlEntry | not-accessible | current | hwStaticLspTnlTable is used to display static LSP token of a static LSP of a specified name. The index of this entry is hwStaticLspTnlName. |
| 1.3.6.1.4.1.2011.5.25.121.1.8.1.1 | ColumnhwStaticLspTnlName | not-accessible | current | Indicates the name of the Static Lsp. |
| 1.3.6.1.4.1.2011.5.25.121.1.8.1.2 | ColumnhwStaticLspTnlToken | read-only | current | Indicates the token of the Static Lsp. |
| 1.3.6.1.4.1.2011.5.25.121.1.9 | TablehwMplsTeVpnQosTable | not-accessible | current | This table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID. The index of this table is hwMplsTnlID. |
| 1.3.6.1.4.1.2011.5.25.121.1.9.1 | RowhwMplsTeVpnQosEntry | not-accessible | current | This table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID. The index of this entry is hwMplsTnlID. |
| 1.3.6.1.4.1.2011.5.25.121.1.9.1.1 | ColumnhwMplsTnlID | not-accessible | current | The value of this object identifies the TE tunnel ID. |
| 1.3.6.1.4.1.2011.5.25.121.1.9.1.2 | ColumnhwMplsTeVpnMaxBandwidth | read-only | current | The value of this object identifies the bandwidth the TE tunnel can provide for VPN QoS. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.9.1.3 | ColumnhwMplsTeVpnAllocatedBandwidth | read-only | current | The value of this object identifies the bandwidth used by VPN QoS, in Kbps. Unit: kbit/s |
| 1.3.6.1.4.1.2011.5.25.121.1.11 | ScalarhwStaticLspInIfIndex | accessible-for-notify | current | Indicates the inbound interface index of a static LSP/CR-LSP. |
| 1.3.6.1.4.1.2011.5.25.121.1.12 | ScalarhwStaticLspInIfName | accessible-for-notify | current | Indicates the name of an inbound interface of a static LSP/CR-LSP. |
| 1.3.6.1.4.1.2011.5.25.121.1.13 | ScalarhwStaticLspDownReason | accessible-for-notify | current | Indicates the reason for static LSP/CR-LSP Down: 0. Other 1. Static LSP/CR-LSP up 2. MPLS disabled on an interface 3. MPLS TE disabled on an interface 4. Route… |
| 1.3.6.1.4.1.2011.5.25.121.2 | NodehwMplsExtendTrap | |||
| 1.3.6.1.4.1.2011.5.25.121.2.1 | NodehwLspTrap | |||
| 1.3.6.1.4.1.2011.5.25.121.2.1.1 | NotificationhwMplsStaticLspUp | current | This notification indicates that the status of referred static LSP changes to Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.2 | NotificationhwMplsStaticLspDown | current | This notification indicates that the status of referred static LSP changes to Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.3 | NotificationhwMplsStaticCRLspUp | current | This notification indicates that the status of referred static CR-LSP changes to Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.4 | NotificationhwMplsStaticCRLspDown | current | This notification indicates that the status of referred static CR-LSP changes to Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.5 | NotificationhwMplsTeFrrProtAval | current | This notification indicates that the primary tunnel is bound to bypass tunnel. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.6 | NotificationhwMplsTeFrrProtNotAval | current | This notification indicates that the primary tunnel is unbound to bypass tunnel. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.7 | NotificationhwMplsTeFrrSwitch | current | This notification indicates that the primary tunnel is switches to the bypass tunnel. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.8 | NotificationhwMplsTeFrrResume | current | This notification indicates that the primary tunnel is switched back from the bypass tunnel. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.9 | NotificationhwMplsTunnelHSBSwitch | current | This notification indicates that the data is switched from the primary CR-LSP to the HSB CR-LSP. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.10 | NotificationhwMplsTunnelHSBResume | current | This notification indicates that the data is switched from the HSB CR-LSP to the primary CR-LSP. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.11 | NotificationhwMplsTunnelOBSwitch | current | This notification indicates that the primary CR-LSP is down and the Ordinary backup CR-LSP is up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.12 | NotificationhwMplsTunnelOBResume | current | This notification indicates that the data is switched from the Ordinary backup CR-LSP to the primary CR-LSP. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.13 | NotificationhwMplsTunnelUp | obsolete | The hwMplsTunnelUp trap indicates that the staus of the tunnel changes into Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.14 | NotificationhwMplsTunnelDown | obsolete | The hwMplsTunnelDown trap indicates that the staus of the tunnel changes into Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.15 | NotificationhwMplsTunnelChangeBw | current | This notification indicates that the bandwidth of the tunnel is changed. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.16 | NotificationhwMplsTunnelTpOamLossSD | current | This object indicates that the loss ratio of the packets carried by the tunnel exceeded the first threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.17 | NotificationhwMplsOamSDRecovery | current | This object indicates that the loss ratio of the packets carried by the tunnel dropped below the first threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.18 | NotificationhwMplsOamLoss | current | This object indicates that TP OAM detected tunnel connectivity faults. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.19 | NotificationhwMplsOamLossRecovery | current | This object indicates that TP OAM did not detect tunnel connectivity faults. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.20 | NotificationhwMplsOamAis | current | This object indicates that TP OAM detected an alarm indication signal. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.21 | NotificationhwMplsOamAisRecovery | current | This object indicates that TP OAM no longer detected alarm indication signals. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.22 | NotificationhwMplsOamRdi | current | This object indicates that TP OAM detected remote defects. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.23 | NotificationhwMplsOamRdiRecovery | current | This object indicates that the remote defects detected by TP OAM were removed. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.24 | NotificationhwMplsOamMeg | current | This object indicates that the names configured on the two ends of the tunnel are inconsistent. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.25 | NotificationhwMplsOamMegRecovery | current | This object indicates that the names configured on the two ends of the tunnel now are consistent. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.26 | NotificationhwMplsOamMep | current | This object indicates that the MEP-IDs configured on the two ends of the tunnel are inconsistent. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.27 | NotificationhwMplsOamMepRecovery | current | This object indicates that the MEP-IDs configured on the two ends of the tunnel now are consistent. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.28 | NotificationhwMplsOamSF | current | This object indicates that the loss ratio of the packets carried by the tunnel exceeded the second threshold in the local link. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.29 | NotificationhwMplsOamSFRecovery | current | This object indicates that the loss ratio of the packets carried by the tunnel dropped below the second threshold in the local link. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.30 | NotificationhwMplsOamPeriod | current | This object indicates that the TP OAM detection periods on the two ends of the tunnel are inconsistent. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.31 | NotificationhwMplsOamPeriodRecovery | current | This object indicates that the TP OAM detection periods on the two ends of the tunnel now are consistent. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.32 | NotificationhwMplsOamLck | current | This object indicates that TP OAM detected the service level of the tunnel has been locked. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.33 | NotificationhwMplsOamLckRecovery | current | This object indicates that TP OAM detected the service level of the tunnel has not been locked. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.34 | NotificationhwMplsOamExcess | current | This object indicates that MPLS OAM detected the tunnel received excess alarm. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.35 | NotificationhwMplsOamExcessRecovery | current | This object indicates that MPLS OAM detected the tunnel received excess alarm end. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.36 | NotificationhwMplsOamMisMatch | current | This object indicates that MPLS OAM detected the tunnel received MisMatch alarm. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.37 | NotificationhwMplsOamMisMatchRecovery | current | This object indicates that MPLS OAM detected the tunnel received MisMatch alarm end. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.38 | NotificationhwMplsOamMisMerge | current | This object indicates that MPLS OAM detected the tunnel received MisMerge alarm. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.39 | NotificationhwMplsOamMisMergeRecovery | current | This object indicates that MPLS OAM detected the tunnel received MisMerge alarm end. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.40 | NotificationhwMplsOamUnknown | current | This object indicates that MPLS OAM detected the tunnel received Unknown alarm. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.41 | NotificationhwMplsOamUnknownRecovery | current | This object indicates that MPLS OAM detected the tunnel received Unknown alarm end. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.42 | NotificationhwMplsOamBDI | current | This object indicates that MPLS OAM detected the tunnel received BDI alarm. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.43 | NotificationhwMplsOamBDIRecovery | current | This object indicates that MPLS OAM detected the tunnel received BDI alarm end. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.44 | NotificationhwMplsOamFail | current | This object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.45 | NotificationhwMplsOamFailRecovery | current | This object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm end. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.46 | NotificationhwMplsTunnelPrimaryUp | current | This notification indicates that the status of the RSVP-TE Primary LSP changes to Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.47 | NotificationhwMplsTunnelPrimaryDown | current | This notification indicates that the status of the RSVP-TE Primary LSP changes to Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.48 | NotificationhwMplsTunnelHotstandbyUp | current | This notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.49 | NotificationhwMplsTunnelHotstandbyDown | current | This notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.50 | NotificationhwMplsTunnelOrdinaryUp | current | This notification indicates that the status of the RSVP-TE Ordinary LSP changes to Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.51 | NotificationhwMplsTunnelOrdinaryDown | current | This notification indicates that the status of the RSVP-TE Ordinary LSP changes to Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.52 | NotificationhwMplsTunnelBesteffortUp | current | This notification indicates that the status of the RSVP-TE Best-effort LSP changes to Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.53 | NotificationhwMplsTunnelBesteffortDown | current | This notification indicates that the status of the RSVP-TE Best-effort LSP changes to Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.54 | NotificationhwMplsTeAutoTunnelDownClear | current | This notification indicates that the TE Auto tunnel Down alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.55 | NotificationhwMplsTeAutoTunnelPrimaryDownClear | current | This notification indicates that the Down alarm about the primary LSP in the TE Auto tunnel was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.56 | NotificationhwMplsTunnelBBSwitch | current | This notification indicates that the primary CR-LSP is Down and the Best-effort backup CR-LSP is Up. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.57 | NotificationhwMplsTunnelBBResume | current | This notification indicates that data is switched from the Best-effort backup CR-LSP to the primary CR-LSP. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.58 | NotificationhwMplsExtTunnelDown | current | This notification indicates that the status of te tunnel changes to Down. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.59 | NotificationhwMplsExtTunnelDownClear | current | This notification indicates that the down alarm of te tunnel was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.60 | NotificationhwMplsOamLocalLock | current | This object indicates that TP OAM detected the tunnel has been locked. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.61 | NotificationhwMplsOamLocalLockRecovery | current | This object indicates that TP OAM detected the tunnel has not been locked. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.62 | NotificationhwMplsTunnelDelete | current | This notification indicates that the mpls te tunnel was deleted. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.63 | NotificationhwMplsLspThresholdExceed | current | This object indicates that lsp count has exceeded the threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.64 | NotificationhwMplsLspThresholdExceedClear | current | This object indicates that lsp count has resumed from exceeding the threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.65 | NotificationhwMplsLspTotalCountExceed | current | This object indicates that lsp count has reached the total count. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.66 | NotificationhwMplsLspTotalCountExceedClear | current | This object indicates that lsp count has resumed from reaching the total count. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.67 | NotificationhwMplsDynamicLabelThresholdExceed | current | This object indicates that label usage has exceeded the threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.68 | NotificationhwMplsDynamicLabelThresholdExceedClear | current | This object indicates that label usage has resumed from exceeding the threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.69 | NotificationhwMplsDynamicLabelTotalCountExceed | current | This object indicates that label count has reached the total count. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.70 | NotificationhwMplsDynamicLabelTotalCountExceedClear | current | This object indicates that label usage count has resumed from reaching the total count. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.71 | NotificationhwMplsResourceThresholdExceed | current | This object indicates that the number of MPLS resources has exceeded the upper threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.72 | NotificationhwMplsResourceThresholdExceedClear | current | This object indicates that the number of MPLS resources has fallen below the lower threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.73 | NotificationhwMplsResourceTotalCountExceed | current | This object indicates that the number of MPLS resources has reached the maximum number. | |
| 1.3.6.1.4.1.2011.5.25.121.2.1.74 | NotificationhwMplsResourceTotalCountExceedClear | current | This object indicates that the number of MPLS resources fallen below the recovery number. | |
| 1.3.6.1.4.1.2011.5.25.121.2.2 | NodehwMplsTrapObjects | |||
| 1.3.6.1.4.1.2011.5.25.121.2.2.1 | ScalarhwMplsTunnelIfName | accessible-for-notify | obsolete | The Tunnel Interface name. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.2 | ScalarhwMplsTunnelFrrConfigOper | accessible-for-notify | obsolete | The value of this object identifies the operation that an FRR configuration is committed on the tunnel. Options: 1.unconfig(0) -indicates the configuration of … |
| 1.3.6.1.4.1.2011.5.25.121.2.2.3 | ScalarhwMplsTunnelDownReason | accessible-for-notify | current | Indicates the alarm reason as below: 1. Other; 2. Static LSP down; 3. Static CR-LSP down; 4. The out interface of the RSVP LSP ingress is down; 5. The resource… |
| 1.3.6.1.4.1.2011.5.25.121.2.2.4 | ScalarhwMplsLspProtocol | accessible-for-notify | current | The value of this object identifies the protocol of the lsp which exceeds the threshold or total count. Options: 1.ldp(1) -indicates the lsp is ldp lsp. 2.bgp(… |
| 1.3.6.1.4.1.2011.5.25.121.2.2.5 | ScalarhwMplsLspThreshold | accessible-for-notify | current | The value of this object identifies the threshold of the lsp. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.6 | ScalarhwMplsLspTotalCount | accessible-for-notify | current | The value of this object identifies the total permit count of lsp. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.7 | ScalarhwMplsLspCurrentCount | accessible-for-notify | current | The value of this object identifies the current count of the lsp. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.8 | ScalarhwMplsTunnelDownLSRID | accessible-for-notify | current | The value of this object identifies the LSR ID of the error node on a tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.9 | ScalarhwMplsTunnelDownIfIpAddr | accessible-for-notify | current | The value of this object identifies the IP address of the error interface on a tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.10 | ScalarhwMplsTunnelDownIfIpAddrType | accessible-for-notify | current | The value of this object identifies the IP address type of the error interface on a tunnel. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.11 | ScalarhwMplsResourceType | accessible-for-notify | current | The value of this object identifies that the number of MPLS resources has exceeded the threshold or the maximum number. Options: 1.autoBypassTunnelIf(1) -Indic… |
| 1.3.6.1.4.1.2011.5.25.121.2.2.12 | ScalarhwMplsResourceCurrentCount | accessible-for-notify | current | The value of this object identifies the number of the resources. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.13 | ScalarhwMplsResourceThreshold | accessible-for-notify | current | The value of this object identifies the threshold for the number of the resources. |
| 1.3.6.1.4.1.2011.5.25.121.2.2.14 | ScalarhwMplsResourceTotalCount | accessible-for-notify | current | The value of this object identifies the maximum number of allowed resources. |
| 1.3.6.1.4.1.2011.5.25.121.2.3 | NotificationhwMplsTunnelFrrConfigChange | obsolete | When the trap indicating that TE-Frr configuration of Tunnel is changed is sent, the cause for the change of TE-FRR configuration of Tunnel is displayed. | |
| 1.3.6.1.4.1.2011.5.25.121.3 | NodehwMplsGlobalObject | |||
| 1.3.6.1.4.1.2011.5.25.121.3.1 | ScalarhwMplsGlobalWorkMode | read-only | current | The work mode of DS-TE system, default mode is nonstandard. Options: 1. standard(1) -indicates work mode of DS-TE system is standard 2. nonstandard(2) -indicat… |
| 1.3.6.1.4.1.2011.5.25.121.3.2 | ScalarhwMplsGlobalBcModel | read-only | current | Bandwidth Constraint Model currently used by this LSR. Options: 1. rdm(1) -indicates that the bandwidth constraint model is RDM. 2. mam(2) -indicates that the … |
| 1.3.6.1.4.1.2011.5.25.121.3.3 | ScalarhwMplsDynamicLabelTotalCount | read-only | current | The value of this object identifies the total permit count of dynamic label. |
| 1.3.6.1.4.1.2011.5.25.121.3.4 | ScalarhwMplsDynamicLabelCurrentCount | read-only | current | The value of this object identifies the current count of the dynamic label. |
| 1.3.6.1.4.1.2011.5.25.121.3.5 | ScalarhwMplsDynamicLabelThresholdUpperLimit | read-only | current | The upper limit threshold value (%) of dynamic label, default value is 80. |
| 1.3.6.1.4.1.2011.5.25.121.3.6 | ScalarhwMplsDynamicLabelThresholdLowerLimit | read-only | current | The lower limit threshold value (%) of dynamic label, default value is 70. |
| 1.3.6.1.4.1.2011.5.25.121.4 | NodehwMplsLspStatistics | |||
| 1.3.6.1.4.1.2011.5.25.121.4.1 | TablehwMplsLspStatisticsTable | not-accessible | current | hwMplsLspStatisticsTable is used to display the number of ingress LSPs, transit LSPs, or egress LSPs of specified types. The index of this table is hwMplsLspSt… |
| 1.3.6.1.4.1.2011.5.25.121.4.1.1 | RowhwMplsLspStatisticsEntry | not-accessible | current | hwMplsLspStatisticsTable is used to display the number of ingress LSPs, transit LSPs, or egress LSPs of specified types. The index of this entry is hwMplsLspSt… |
| 1.3.6.1.4.1.2011.5.25.121.4.1.1.1 | ColumnhwMplsLspStatisticsLspType | not-accessible | current | This object indicates the LSP type. Options: 1. staticLsp(1) -indicates the static LSP. 2. staticCrLsp(2) -indicates the static CR-LSP. 3. ldpLsp(3) -indicates… |
| 1.3.6.1.4.1.2011.5.25.121.4.1.1.2 | ColumnhwMplsLspStatisticsIngressLspCount | read-only | current | This object indicates the number of ingress LSPs of a specified type. |
| 1.3.6.1.4.1.2011.5.25.121.4.1.1.3 | ColumnhwMplsLspStatisticsTransitLspCount | read-only | current | This object indicates the number of transit LSPs of a specified type. |
| 1.3.6.1.4.1.2011.5.25.121.4.1.1.4 | ColumnhwMplsLspStatisticsEgressLspCount | read-only | current | This object indicates the number of egress LSPs of a specified type. |
| 1.3.6.1.4.1.2011.5.25.121.4.1.1.5 | ColumnhwMplsLspStatisticsTotalLspCount | read-only | current | This object indicates the total number of the ingress LSPs, transit LSPs and egress LSP of specified types. |
| 1.3.6.1.4.1.2011.5.25.121.4.2 | TablehwMplsTrafficStatisticsStaticLspTable | not-accessible | current | Indicates the traffic statistics of a LSP. The indexes of this table is hwMplsTrafficStatisticsStaticLspName. |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1 | RowhwMplsTrafficStatisticsStaticLspEntry | not-accessible | current | Indicates the traffic statistics of a LSP. The indexes of this entry is hwMplsTrafficStatisticsStaticLspName. |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.1 | ColumnhwMplsTrafficStatisticsStaticLspName | not-accessible | current | Indicates the name of the static LSP or CR-LSP. The name is appointed when the static LSP or CR-LSP is created. |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.2 | ColumnhwMplsTrafficStatisticsStaticLspForwardInBytes | read-only | current | An estimate of the forward of bistatic LSP's current incoming traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics,… |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.3 | ColumnhwMplsTrafficStatisticsStaticLspForwardInPackets | read-only | current | An estimate of the forward of bistatic LSP's current incoming traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistic… |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.4 | ColumnhwMplsTrafficStatisticsStaticLspForwardOutBytes | read-only | current | An estimate of the forward of bistatic LSP's current outgoing traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics,… |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.5 | ColumnhwMplsTrafficStatisticsStaticLspForwardOutPackets | read-only | current | An estimate of the forward of bistatic LSP's current outgoing traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistic… |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.6 | ColumnhwMplsTrafficStatisticsStaticLspBackwardInBytes | read-only | current | An estimate of the backward of bistatic LSP's current incoming traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics… |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.7 | ColumnhwMplsTrafficStatisticsStaticLspBackwardInPackets | read-only | current | An estimate of the backward of bistatic LSP's current incoming traffic statistics in units of packets. For a sub-layer which has no concept of traffic statisti… |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.8 | ColumnhwMplsTrafficStatisticsStaticLspBackwardOutBytes | read-only | current | An estimate of the backward of bistatic LSP's current outgoing traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics… |
| 1.3.6.1.4.1.2011.5.25.121.4.2.1.9 | ColumnhwMplsTrafficStatisticsStaticLspBackwardOutPackets | read-only | current | An estimate of the backward of bistatic LSP's current outgoing traffic statistics in units of packets. For a sub-layer which has no concept of traffic statisti… |
| 1.3.6.1.4.1.2011.5.25.121.6 | NodehwMplsExtendConformance | |||
| 1.3.6.1.4.1.2011.5.25.121.6.1 | NodehwMplsExtendGroups | |||
| 1.3.6.1.4.1.2011.5.25.121.6.1.1 | GrouphwMplsTunnelGroup | current | Indicate the atrributes of the tunnel. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.2 | GrouphwStaticLspGroup | current | Indicate the atrributes of the static lsp. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.3 | GrouphwMplsDsTeGroup | current | Indicate the atrributes about DS-TE. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.4 | GrouphwMplsLspStatisticsGroup | current | Indicate LSP statistics. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.5 | GrouphwMplsObsoleteGroup | obsolete | Indicate the OBSOLETE objects of MPLS. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.6 | GrouphwMplsTrapGroup | current | For mpls trap object. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.7 | GrouphwMplsRingGroup | current | For mpls ring trap object. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.8 | GrouphwMplsGlobalGroup | current | For mpls global object. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.9 | GrouphwMplsLspGroup | current | For mpls lsp object. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.10 | GrouphwMplsLspTrafficStatisticGroup | current | Indicate the traffic statistic of the LSP. | |
| 1.3.6.1.4.1.2011.5.25.121.6.1.11 | GrouphwMplsResourceGroup | current | For mpls resource object. | |
| 1.3.6.1.4.1.2011.5.25.121.6.2 | NodehwMplsExtendCompliances | |||
| 1.3.6.1.4.1.2011.5.25.121.6.2.1 | GrouphwExtendTrapGroup | current | Indicate the traps. | |
| 1.3.6.1.4.1.2011.5.25.121.6.2.2 | GrouphwObsoleteTrapGroup | obsolete | Indicate the Obsolete traps. | |
| 1.3.6.1.4.1.2011.5.25.121.6.2.3 | CompliancehwMplsModuleCompliance | current | hwMplsModuleCompliance | |
| 1.3.6.1.4.1.2011.5.25.121.7 | NodehwMplsRingMib | |||
| 1.3.6.1.4.1.2011.5.25.121.7.1 | TablehwMplsRingTable | not-accessible | current | Indicates the table information of the MPLS ring. |
| 1.3.6.1.4.1.2011.5.25.121.7.1.1 | RowhwMplsRingEntry | not-accessible | current | Indicates the table information of the MPLS ring. |
| 1.3.6.1.4.1.2011.5.25.121.7.1.1.1 | ColumnhwMplsRingID | not-accessible | current | Indicates the ID of the MPLS ring. |
| 1.3.6.1.4.1.2011.5.25.121.7.1.1.2 | ColumnhwMplsRingNodeID | read-only | current | Indicates the ID of the current Node on the MPLS ring. |
| 1.3.6.1.4.1.2011.5.25.121.7.1.1.3 | ColumnhwMplsRingName | read-only | current | Indicates the name of MPLS ring. |
| 1.3.6.1.4.1.2011.5.25.121.7.1.1.4 | ColumnhwMplsRingDirection | read-only | current | Indicates the direction of the MPLS ring. |
| 1.3.6.1.4.1.2011.5.25.121.7.1.1.5 | ColumnhwMplsRingSwitchReason | read-only | current | Indicates the switch reason of the MPLS ring. |
| 1.3.6.1.4.1.2011.5.25.121.7.2 | NodehwMplsRingTrap | |||
| 1.3.6.1.4.1.2011.5.25.121.7.2.1 | NotificationhwMplsRingSwitch | obsolete | The notification indicates that the MPLS ring switched. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.2 | NotificationhwMplsRingResume | obsolete | The notification indicates that the MPLS ring resumed. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.3 | NotificationhwMplsRingWestOamLoss | current | The notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the west of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.4 | NotificationhwMplsRingWestOamLossClear | current | The notification indicates that the hwMplsRingWestOamLoss alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.5 | NotificationhwMplsRingEastOamLoss | current | The notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the east of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.6 | NotificationhwMplsRingEastOamLossClear | current | The notification indicates that the hwMplsRingEastOamLoss alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.7 | NotificationhwMplsRingWestOamRDI | current | The notification indicates that RDI packets are received in the west of the MPLS ring, indicating that a fault occurs on the forward ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.8 | NotificationhwMplsRingWestOamRDIClear | current | The notification indicates that the hwMplsRingWestOamRDI alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.9 | NotificationhwMplsRingEastOamRDI | current | The notification indicates that RDI packets are received in the east of the MPLS ring, indicating that a fault occurs on the forward ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.10 | NotificationhwMplsRingEastOamRDIClear | current | The notification indicates that the hwMplsRingEastOamRDI alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.11 | NotificationhwMplsRingWestOamUnexpectedMEG | current | The notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the west of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.12 | NotificationhwMplsRingWestOamUnexpectedMEGClear | current | The notification indicates that the hwMplsRingWestOamUnexpectedMEG alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.13 | NotificationhwMplsRingEastOamUnexpectedMEG | current | The notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the east of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.14 | NotificationhwMplsRingEastOamUnexpectedMEGClear | current | The notification indicates that the hwMplsRingEastOamUnexpectedMEG alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.15 | NotificationhwMplsRingWestOamUnexpectedPeriod | current | The notification indicates that a CCM frame carrying a correct MEG level, MEG ID, and MEP ID but incorrect period value is received in the west MEP of the MPLS… | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.16 | NotificationhwMplsRingWestOamUnexpectedPeriodClear | current | The notification indicates that the hwMplsRingWestOamUnexpectedPeriod alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.17 | NotificationhwMplsRingEastOamUnexpectedPeriod | current | The notification indicates that a CCM frame carrying a correct MEG level, MEG ID, and MEP ID but incorrect period value is received in the east MEP of the MPLS… | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.18 | NotificationhwMplsRingEastOamUnexpectedPeriodClear | current | The notification indicates that the hwMplsRingEastOamUnexpectedPeriod alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.19 | NotificationhwMplsRingWestOamExcess | current | The notification indicates that five or more CV/FFD packets are correctly received within three consecutive cycles in the west of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.20 | NotificationhwMplsRingWestOamExcessClear | current | The notification indicates that the hwMplsRingWestOamExcess alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.21 | NotificationhwMplsRingEastOamExcess | current | The notification indicates that five or more CV/FFD packets are correctly received within three consecutive cycles in the east of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.22 | NotificationhwMplsRingEastOamExcessClear | current | The notification indicates that the hwMplsRingEastOamExcess alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.23 | NotificationhwMplsRingWestOamSD | current | The notification indicates that the number of packets for connectivity check received in the west of the MPLS ring is smaller than the SD threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.24 | NotificationhwMplsRingWestOamSDClear | current | The notification indicates that the hwMplsRingWestOamSD alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.25 | NotificationhwMplsRingEastOamSD | current | The notification indicates that the number of packets for connectivity check received in the east of the MPLS ring is smaller than the SD threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.26 | NotificationhwMplsRingEastOamSDClear | current | The notification indicates that the hwMplsRingEastOamSD alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.27 | NotificationhwMplsRingWestOamSF | current | The notification indicates that the number of packets for connectivity check received in the west of the MPLS ring is smaller than the SF threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.28 | NotificationhwMplsRingWestOamSFClear | current | The notification indicates that the hwMplsRingWestOamSF alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.29 | NotificationhwMplsRingEastOamSF | current | The notification indicates that the number of packets for connectivity check received in the east of the MPLS ring is smaller than the SF threshold. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.30 | NotificationhwMplsRingEastOamSFClear | current | The notification indicates that the hwMplsRingEastOamSF alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.31 | NotificationhwMplsRingWestAPSSwitch | current | The notification indicates that APS switching occurs in the west of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.32 | NotificationhwMplsRingWestAPSResume | current | The notification indicates that APS switches back in the west of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.33 | NotificationhwMplsRingEastAPSSwitch | current | The notification indicates that APS switching occurs in the east of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.34 | NotificationhwMplsRingEastAPSResume | current | The notification indicates that APS switches back in the east of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.35 | NotificationhwMplsRingWestAPSSwitchFail | current | The notification indicates that the remote APS switching fails in the west of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.36 | NotificationhwMplsRingWestAPSSwitchFailClear | current | The notification indicates that the hwMplsRingWestAPSSwitchFail alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.37 | NotificationhwMplsRingEastAPSSwitchFail | current | The notification indicates that the remote APS switching fails in the east of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.38 | NotificationhwMplsRingEastAPSSwitchFailClear | current | The notification indicates that the hwMplsRingEastAPSSwitchFail alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.39 | NotificationhwMplsRingWestAPSLost | current | The notification indicates that APS packets are missing in the west of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.40 | NotificationhwMplsRingWestAPSLostClear | current | The notification indicates that the hwMplsRingWestAPSLost alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.41 | NotificationhwMplsRingEastAPSLost | current | The notification indicates that APS packets are missing in the east of the MPLS ring. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.42 | NotificationhwMplsRingEastAPSLostClear | current | The notification indicates that the hwMplsRingEastAPSLost alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.43 | NotificationhwMplsRingWestAPSMismatch | current | The notification indicates that the source ID carried by APS packets received in the west is different from the peer source ID configured for the west state ma… | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.44 | NotificationhwMplsRingWestAPSMismatchClear | current | The notification indicates that the hwMplsRingWestAPSMismatch alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.45 | NotificationhwMplsRingEastAPSMismatch | current | The notification indicates that the source ID carried by APS packets received in the east is different from the peer source ID configured for the east state ma… | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.46 | NotificationhwMplsRingEastAPSMismatchClear | current | The notification indicates that the hwMplsRingEastAPSMismatch alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.47 | NotificationhwMplsRingWestOamUnexpectedMEP | current | The notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the west of the MPLS rin… | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.48 | NotificationhwMplsRingWestOamUnexpectedMEPClear | current | The notification indicates that the hwMplsRingWestOamUnexpectedMEP alarm was cleared. | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.49 | NotificationhwMplsRingEastOamUnexpectedMEP | current | The notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the east of the MPLS rin… | |
| 1.3.6.1.4.1.2011.5.25.121.7.2.50 | NotificationhwMplsRingEastOamUnexpectedMEPClear | current | The notification indicates that the hwMplsRingEastOamUnexpectedMEP alarm was cleared. |