MPLS-LDP-STD-MIB
126 objects
Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for the 'Multiprotocol Label Switching, Label Distribution Protocol, LDP' document.
Imported Objects
| DIFFSERV-MIB | IndexInteger IndexIntegerNextFree |
| INET-ADDRESS-MIB | InetAddress InetAddressPrefixLength InetAddressType InetPortNumber |
| MPLS-LSR-STD-MIB | MplsIndexType |
| MPLS-TC-STD-MIB | MplsLabelDistributionMethod MplsLdpIdentifier MplsLdpLabelType MplsLspType MplsLsrIdentifier MplsRetentionMode mplsStdMIB |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TimeInterval TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.166.4 | IdentitymplsLdpStdMIB | Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: … | ||
| 1.3.6.1.2.1.10.166.4.0 | NodemplsLdpNotifications | |||
| 1.3.6.1.2.1.10.166.4.0.1 | NotificationmplsLdpInitSessionThresholdExceeded | current | This notification is generated when the value of the 'mplsLdpEntityInitSessionThreshold' object is not zero, and the number of Session Initialization messages … | |
| 1.3.6.1.2.1.10.166.4.0.2 | NotificationmplsLdpPathVectorLimitMismatch | current | This notification is sent when the 'mplsLdpEntityPathVectorLimit' does NOT match the value of the 'mplsLdpPeerPathVectorLimit' for a specific Entity. | |
| 1.3.6.1.2.1.10.166.4.0.3 | NotificationmplsLdpSessionUp | current | If this notification is sent when the value of 'mplsLdpSessionState' enters the 'operational(5)' state. | |
| 1.3.6.1.2.1.10.166.4.0.4 | NotificationmplsLdpSessionDown | current | This notification is sent when the value of 'mplsLdpSessionState' leaves the 'operational(5)' state. | |
| 1.3.6.1.2.1.10.166.4.1 | NodemplsLdpObjects | |||
| 1.3.6.1.2.1.10.166.4.1.1 | NodemplsLdpLsrObjects | |||
| 1.3.6.1.2.1.10.166.4.1.1.1 | ScalarmplsLdpLsrId | read-only | current | The Label Switching Router's Identifier. |
| 1.3.6.1.2.1.10.166.4.1.1.2 | ScalarmplsLdpLsrLoopDetectionCapable | read-only | current | A indication of whether this Label Switching Router supports loop detection. none(1) on this LSR. other(2) by a method other than those listed below. hopCount(… |
| 1.3.6.1.2.1.10.166.4.1.2 | NodemplsLdpEntityObjects | |||
| 1.3.6.1.2.1.10.166.4.1.2.1 | ScalarmplsLdpEntityLastChange | read-only | current | The value of sysUpTime at the time of the most recent addition or deletion of an entry to/from the mplsLdpEntityTable/mplsLdpEntityStatsTable, or the most rece… |
| 1.3.6.1.2.1.10.166.4.1.2.2 | ScalarmplsLdpEntityIndexNext | read-only | current | This object contains an appropriate value to be used for mplsLdpEntityIndex when creating entries in the mplsLdpEntityTable. The value 0 indicates that no unas… |
| 1.3.6.1.2.1.10.166.4.1.2.3 | TablemplsLdpEntityTable | not-accessible | current | This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switching Router (LSR) or Label Edge Router (LER). |
| 1.3.6.1.2.1.10.166.4.1.2.3.1 | RowmplsLdpEntityEntry | not-accessible | current | An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.1 | ColumnmplsLdpEntityLdpId | not-accessible | current | The LDP identifier. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.2 | ColumnmplsLdpEntityIndex | not-accessible | current | This index is used as a secondary index to uniquely identify this row. Before creating a row in this table, the 'mplsLdpEntityIndexNext' object should be retri… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.3 | ColumnmplsLdpEntityProtocolVersion | read-create | current | The version number of the LDP protocol which will be used in the session initialization message. Section 3.5.3 in the LDP Specification specifies that the vers… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.4 | ColumnmplsLdpEntityAdminStatus | read-create | current | The administrative status of this LDP Entity. If this object is changed from 'enable' to 'disable' and this entity has already attempted to establish contact w… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.5 | ColumnmplsLdpEntityOperStatus | read-only | current | The operational status of this LDP Entity. The value of unknown(1) indicates that the operational status cannot be determined at this time. The value of unknow… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.6 | ColumnmplsLdpEntityTcpPort | read-create | current | The TCP Port for LDP. The default value is the well-known value of this port. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.7 | ColumnmplsLdpEntityUdpDscPort | read-create | current | The UDP Discovery Port for LDP. The default value is the well-known value for this port. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.8 | ColumnmplsLdpEntityMaxPduLength | read-create | current | The maximum PDU Length that is sent in the Common Session Parameters of an Initialization Message. According to the LDP Specification [RFC3036] a value of 255 … |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.9 | ColumnmplsLdpEntityKeepAliveHoldTimer | read-create | current | The 16-bit integer value which is the proposed keep alive hold timer for this LDP Entity. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.10 | ColumnmplsLdpEntityHelloHoldTimer | read-create | current | The 16-bit integer value which is the proposed Hello hold timer for this LDP Entity. The Hello Hold time in seconds. An LSR maintains a record of Hellos receiv… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.11 | ColumnmplsLdpEntityInitSessionThreshold | read-create | current | When attempting to establish a session with a given Peer, the given LDP Entity should send out the SNMP notification, 'mplsLdpInitSessionThresholdExceeded', wh… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.12 | ColumnmplsLdpEntityLabelDistMethod | read-create | current | For any given LDP session, the method of label distribution must be specified. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.13 | ColumnmplsLdpEntityLabelRetentionMode | read-create | current | The LDP Entity can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized lab… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.14 | ColumnmplsLdpEntityPathVectorLimit | read-create | current | If the value of this object is 0 (zero) then Loop Detection for Path Vectors is disabled. Otherwise, if this object has a value greater than zero, then Loop De… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.15 | ColumnmplsLdpEntityHopCountLimit | read-create | current | If the value of this object is 0 (zero), then Loop Detection using Hop Counters is disabled. If the value of this object is greater than 0 (zero) then Loop Det… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.16 | ColumnmplsLdpEntityTransportAddrKind | read-create | current | This specifies whether the loopback or interface address is to be used as the transport address in the transport address TLV of the hello message. If the value… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.17 | ColumnmplsLdpEntityTargetPeer | read-create | current | If this LDP entity uses targeted peer then set this to true. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.18 | ColumnmplsLdpEntityTargetPeerAddrType | read-create | current | The type of the internetwork layer address used for the Extended Discovery. This object indicates how the value of mplsLdpEntityTargetPeerAddr is to be interpr… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.19 | ColumnmplsLdpEntityTargetPeerAddr | read-create | current | The value of the internetwork layer address used for the Extended Discovery. The value of mplsLdpEntityTargetPeerAddrType specifies how this address is to be i… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.20 | ColumnmplsLdpEntityLabelType | read-create | current | Specifies the optional parameters for the LDP Initialization Message. If the value is generic(1) then no optional parameters will be sent in the LDP Initializa… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.21 | ColumnmplsLdpEntityDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this entity's counters suffered a discontinuity. The relevant counters are the s… |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.22 | ColumnmplsLdpEntityStorageType | read-create | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.10.166.4.1.2.3.1.23 | ColumnmplsLdpEntityRowStatus | read-create | current | The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Chan… |
| 1.3.6.1.2.1.10.166.4.1.2.4 | TablemplsLdpEntityStatsTable | not-accessible | current | This table is a read-only table which augments the mplsLdpEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on t… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1 | RowmplsLdpEntityStatsEntry | not-accessible | current | A row in this table contains statistical information about an LDP Entity. Some counters contained in a row are for fatal errors received during a former LDP Se… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.1 | ColumnmplsLdpEntityStatsSessionAttempts | read-only | current | A count of the Session Initialization messages which were sent or received by this LDP Entity and were NAK'd. In other words, this counter counts the number of… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.2 | ColumnmplsLdpEntityStatsSessionRejectedNoHelloErrors | read-only | current | A count of the Session Rejected/No Hello Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occu… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.3 | ColumnmplsLdpEntityStatsSessionRejectedAdErrors | read-only | current | A count of the Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of … |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.4 | ColumnmplsLdpEntityStatsSessionRejectedMaxPduErrors | read-only | current | A count of the Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.5 | ColumnmplsLdpEntityStatsSessionRejectedLRErrors | read-only | current | A count of the Session Rejected/Parameters Label Range Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter … |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.6 | ColumnmplsLdpEntityStatsBadLdpIdentifierErrors | read-only | current | This object counts the number of Bad LDP Identifier Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.7 | ColumnmplsLdpEntityStatsBadPduLengthErrors | read-only | current | This object counts the number of Bad PDU Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in … |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.8 | ColumnmplsLdpEntityStatsBadMessageLengthErrors | read-only | current | This object counts the number of Bad Message Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.9 | ColumnmplsLdpEntityStatsBadTlvLengthErrors | read-only | current | This object counts the number of Bad TLV Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in … |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.10 | ColumnmplsLdpEntityStatsMalformedTlvValueErrors | read-only | current | This object counts the number of Malformed TLV Value Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuitie… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.11 | ColumnmplsLdpEntityStatsKeepAliveTimerExpErrors | read-only | current | This object counts the number of Session Keep Alive Timer Expired Errors detected by the session(s) (past and present) associated with this LDP Entity. Discont… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.12 | ColumnmplsLdpEntityStatsShutdownReceivedNotifications | read-only | current | This object counts the number of Shutdown Notifications received related to session(s) (past and present) associated with this LDP Entity. Discontinuities in t… |
| 1.3.6.1.2.1.10.166.4.1.2.4.1.13 | ColumnmplsLdpEntityStatsShutdownSentNotifications | read-only | current | This object counts the number of Shutdown Notfications sent related to session(s) (past and present) associated with this LDP Entity. Discontinuities in the va… |
| 1.3.6.1.2.1.10.166.4.1.3 | NodemplsLdpSessionObjects | |||
| 1.3.6.1.2.1.10.166.4.1.3.1 | ScalarmplsLdpPeerLastChange | read-only | current | The value of sysUpTime at the time of the most recent addition or deletion to/from the mplsLdpPeerTable/mplsLdpSessionTable. |
| 1.3.6.1.2.1.10.166.4.1.3.2 | TablemplsLdpPeerTable | not-accessible | current | Information about LDP peers known by Entities in the mplsLdpEntityTable. The information in this table is based on information from the Entity-Peer interaction… |
| 1.3.6.1.2.1.10.166.4.1.3.2.1 | RowmplsLdpPeerEntry | not-accessible | current | Information about a single Peer which is related to a Session. This table is augmented by the mplsLdpSessionTable. |
| 1.3.6.1.2.1.10.166.4.1.3.2.1.1 | ColumnmplsLdpPeerLdpId | not-accessible | current | The LDP identifier of this LDP Peer. |
| 1.3.6.1.2.1.10.166.4.1.3.2.1.2 | ColumnmplsLdpPeerLabelDistMethod | read-only | current | For any given LDP session, the method of label distribution must be specified. |
| 1.3.6.1.2.1.10.166.4.1.3.2.1.3 | ColumnmplsLdpPeerPathVectorLimit | read-only | current | If the value of this object is 0 (zero) then Loop Dection for Path Vectors for this Peer is disabled. Otherwise, if this object has a value greater than zero, … |
| 1.3.6.1.2.1.10.166.4.1.3.2.1.4 | ColumnmplsLdpPeerTransportAddrType | read-only | current | The type of the Internet address for the mplsLdpPeerTransportAddr object. The LDP specification describes this as being either an IPv4 Transport Address or IPv… |
| 1.3.6.1.2.1.10.166.4.1.3.2.1.5 | ColumnmplsLdpPeerTransportAddr | read-only | current | The Internet address advertised by the peer in the Hello Message or the Hello source address. The type of this address is specified by the value of the mplsLdp… |
| 1.3.6.1.2.1.10.166.4.1.3.3 | TablemplsLdpSessionTable | not-accessible | current | A table of Sessions between the LDP Entities and LDP Peers. This table AUGMENTS the mplsLdpPeerTable. Each row in this table represents a single session. |
| 1.3.6.1.2.1.10.166.4.1.3.3.1 | RowmplsLdpSessionEntry | not-accessible | current | An entry in this table represents information on a single session between an LDP Entity and LDP Peer. The information contained in a row is read-only. Please n… |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.1 | ColumnmplsLdpSessionStateLastChange | read-only | current | The value of sysUpTime at the time this Session entered its current state as denoted by the mplsLdpSessionState object. |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.2 | ColumnmplsLdpSessionState | read-only | current | The current state of the session, all of the states 1 to 5 are based on the state machine for session negotiation behavior. |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.3 | ColumnmplsLdpSessionRole | read-only | current | During session establishment the LSR/LER takes either the active role or the passive role based on address comparisons. This object indicates whether this LSR/… |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.4 | ColumnmplsLdpSessionProtocolVersion | read-only | current | The version of the LDP Protocol which this session is using. This is the version of the LDP protocol which has been negotiated during session initialization. |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.5 | ColumnmplsLdpSessionKeepAliveHoldTimeRem | read-only | current | The keep alive hold time remaining for this session. |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.6 | ColumnmplsLdpSessionKeepAliveTime | read-only | current | The negotiated KeepAlive Time which represents the amount of seconds between keep alive messages. The mplsLdpEntityKeepAliveHoldTimer related to this Session i… |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.7 | ColumnmplsLdpSessionMaxPduLength | read-only | current | The value of maximum allowable length for LDP PDUs for this session. This value may have been negotiated during the Session Initialization. This object is rela… |
| 1.3.6.1.2.1.10.166.4.1.3.3.1.8 | ColumnmplsLdpSessionDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this session's counters suffered a discontinuity. The relevant counters are the … |
| 1.3.6.1.2.1.10.166.4.1.3.4 | TablemplsLdpSessionStatsTable | not-accessible | current | A table of statistics for Sessions between LDP Entities and LDP Peers. This table AUGMENTS the mplsLdpPeerTable. |
| 1.3.6.1.2.1.10.166.4.1.3.4.1 | RowmplsLdpSessionStatsEntry | not-accessible | current | An entry in this table represents statistical information on a single session between an LDP Entity and LDP Peer. |
| 1.3.6.1.2.1.10.166.4.1.3.4.1.1 | ColumnmplsLdpSessionStatsUnknownMesTypeErrors | read-only | current | This object counts the number of Unknown Message Type Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occ… |
| 1.3.6.1.2.1.10.166.4.1.3.4.1.2 | ColumnmplsLdpSessionStatsUnknownTlvErrors | read-only | current | This object counts the number of Unknown TLV Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occur at re-… |
| 1.3.6.1.2.1.10.166.4.1.3.5 | NodemplsLdpHelloAdjacencyObjects | |||
| 1.3.6.1.2.1.10.166.4.1.3.5.1 | TablemplsLdpHelloAdjacencyTable | not-accessible | current | A table of Hello Adjacencies for Sessions. |
| 1.3.6.1.2.1.10.166.4.1.3.5.1.1 | RowmplsLdpHelloAdjacencyEntry | not-accessible | current | Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello Adjacencies. |
| 1.3.6.1.2.1.10.166.4.1.3.5.1.1.1 | ColumnmplsLdpHelloAdjacencyIndex | not-accessible | current | An identifier for this specific adjacency. |
| 1.3.6.1.2.1.10.166.4.1.3.5.1.1.2 | ColumnmplsLdpHelloAdjacencyHoldTimeRem | read-only | current | If the value of this object is 65535, this means that the hold time is infinite (i.e., wait forever). Otherwise, the time remaining for this Hello Adjacency to… |
| 1.3.6.1.2.1.10.166.4.1.3.5.1.1.3 | ColumnmplsLdpHelloAdjacencyHoldTime | read-only | current | The Hello hold time which is negotiated between the Entity and the Peer. The entity associated with this Hello Adjacency issues a proposed Hello Hold Time valu… |
| 1.3.6.1.2.1.10.166.4.1.3.5.1.1.4 | ColumnmplsLdpHelloAdjacencyType | read-only | current | This adjacency is the result of a 'link' hello if the value of this object is link(1). Otherwise, it is a result of a 'targeted' hello, targeted(2). |
| 1.3.6.1.2.1.10.166.4.1.3.6 | TablemplsInSegmentLdpLspTable | not-accessible | current | A table of LDP LSP's which map to the mplsInSegmentTable in the MPLS-LSR-STD-MIB module. |
| 1.3.6.1.2.1.10.166.4.1.3.6.1 | RowmplsInSegmentLdpLspEntry | not-accessible | current | An entry in this table represents information on a single LDP LSP which is represented by a session's index triple (mplsLdpEntityLdpId, mplsLdpEntityIndex, mpl… |
| 1.3.6.1.2.1.10.166.4.1.3.6.1.1 | ColumnmplsInSegmentLdpLspIndex | not-accessible | current | This contains the same value as the mplsInSegmentIndex in the MPLS-LSR-STD-MIB's mplsInSegmentTable. |
| 1.3.6.1.2.1.10.166.4.1.3.6.1.2 | ColumnmplsInSegmentLdpLspLabelType | read-only | current | The Layer 2 Label Type. |
| 1.3.6.1.2.1.10.166.4.1.3.6.1.3 | ColumnmplsInSegmentLdpLspType | read-only | current | The type of LSP connection. |
| 1.3.6.1.2.1.10.166.4.1.3.7 | TablemplsOutSegmentLdpLspTable | not-accessible | current | A table of LDP LSP's which map to the mplsOutSegmentTable in the MPLS-LSR-STD-MIB. |
| 1.3.6.1.2.1.10.166.4.1.3.7.1 | RowmplsOutSegmentLdpLspEntry | not-accessible | current | An entry in this table represents information on a single LDP LSP which is represented by a session's index triple (mplsLdpEntityLdpId, mplsLdpEntityIndex, mpl… |
| 1.3.6.1.2.1.10.166.4.1.3.7.1.1 | ColumnmplsOutSegmentLdpLspIndex | not-accessible | current | This contains the same value as the mplsOutSegmentIndex in the MPLS-LSR-STD-MIB's mplsOutSegmentTable. |
| 1.3.6.1.2.1.10.166.4.1.3.7.1.2 | ColumnmplsOutSegmentLdpLspLabelType | read-only | current | The Layer 2 Label Type. |
| 1.3.6.1.2.1.10.166.4.1.3.7.1.3 | ColumnmplsOutSegmentLdpLspType | read-only | current | The type of LSP connection. |
| 1.3.6.1.2.1.10.166.4.1.3.8 | NodemplsFecObjects | |||
| 1.3.6.1.2.1.10.166.4.1.3.8.1 | ScalarmplsFecLastChange | read-only | current | The value of sysUpTime at the time of the most recent addition/deletion of an entry to/from the mplsLdpFectTable or the most recent change in values to any obj… |
| 1.3.6.1.2.1.10.166.4.1.3.8.2 | ScalarmplsFecIndexNext | read-only | current | This object contains an appropriate value to be used for mplsFecIndex when creating entries in the mplsFecTable. The value 0 indicates that no unassigned entri… |
| 1.3.6.1.2.1.10.166.4.1.3.8.3 | TablemplsFecTable | not-accessible | current | This table represents the FEC (Forwarding Equivalence Class) Information associated with an LSP. |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1 | RowmplsFecEntry | not-accessible | current | Each row represents a single FEC Element. |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1.1 | ColumnmplsFecIndex | not-accessible | current | The index which uniquely identifies this entry. |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1.2 | ColumnmplsFecType | read-create | current | The type of the FEC. If the value of this object is 'prefix(1)' then the FEC type described by this row is an address prefix. If the value of this object is 'h… |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1.3 | ColumnmplsFecAddrPrefixLength | read-create | current | If the value of the 'mplsFecType' is 'hostAddress(2)' then this object is undefined. If the value of 'mplsFecType' is 'prefix(1)' then the value of this object… |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1.4 | ColumnmplsFecAddrType | read-create | current | The value of this object is the type of the Internet address. The value of this object, decides how the value of the mplsFecAddr object is interpreted. |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1.5 | ColumnmplsFecAddr | read-create | current | The value of this object is interpreted based on the value of the 'mplsFecAddrType' object. This address is then further interpretted as an being used with the… |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1.6 | ColumnmplsFecStorageType | read-create | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.10.166.4.1.3.8.3.1.7 | ColumnmplsFecRowStatus | read-create | current | The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified, except to set t… |
| 1.3.6.1.2.1.10.166.4.1.3.9 | ScalarmplsLdpLspFecLastChange | read-only | current | The value of sysUpTime at the time of the most recent addition/deletion of an entry to/from the mplsLdpLspFecTable or the most recent change in values to any o… |
| 1.3.6.1.2.1.10.166.4.1.3.10 | TablemplsLdpLspFecTable | not-accessible | current | A table which shows the relationship between LDP LSPs and FECs. Each row represents a single LDP LSP to FEC association. |
| 1.3.6.1.2.1.10.166.4.1.3.10.1 | RowmplsLdpLspFecEntry | not-accessible | current | An entry represents a LDP LSP to FEC association. |
| 1.3.6.1.2.1.10.166.4.1.3.10.1.1 | ColumnmplsLdpLspFecSegment | not-accessible | current | If the value is inSegment(1), then this indicates that the following index, mplsLdpLspFecSegmentIndex, contains the same value as the mplsInSegmentLdpLspIndex.… |
| 1.3.6.1.2.1.10.166.4.1.3.10.1.2 | ColumnmplsLdpLspFecSegmentIndex | not-accessible | current | This index is interpretted by using the value of the mplsLdpLspFecSegment. If the mplsLdpLspFecSegment is inSegment(1), then this index has the same value as m… |
| 1.3.6.1.2.1.10.166.4.1.3.10.1.3 | ColumnmplsLdpLspFecIndex | not-accessible | current | This index identifies the FEC entry in the mplsFecTable associated with this session. In other words, the value of this index is the same as the value of the m… |
| 1.3.6.1.2.1.10.166.4.1.3.10.1.4 | ColumnmplsLdpLspFecStorageType | read-create | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.2.1.10.166.4.1.3.10.1.5 | ColumnmplsLdpLspFecRowStatus | read-create | current | The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified. The Agent shoul… |
| 1.3.6.1.2.1.10.166.4.1.3.11 | TablemplsLdpSessionPeerAddrTable | not-accessible | current | This table 'extends' the mplsLdpSessionTable. This table is used to store Label Address Information from Label Address Messages received by this LSR from Peers… |
| 1.3.6.1.2.1.10.166.4.1.3.11.1 | RowmplsLdpSessionPeerAddrEntry | not-accessible | current | An entry in this table represents information on a session's single next hop address which was advertised in an Address Message from the LDP peer. The informat… |
| 1.3.6.1.2.1.10.166.4.1.3.11.1.1 | ColumnmplsLdpSessionPeerAddrIndex | not-accessible | current | An index which uniquely identifies this entry within a given session. |
| 1.3.6.1.2.1.10.166.4.1.3.11.1.2 | ColumnmplsLdpSessionPeerNextHopAddrType | read-only | current | The internetwork layer address type of this Next Hop Address as specified in the Label Address Message associated with this Session. The value of this object i… |
| 1.3.6.1.2.1.10.166.4.1.3.11.1.3 | ColumnmplsLdpSessionPeerNextHopAddr | read-only | current | The next hop address. The type of this address is specified by the value of the mplsLdpSessionPeerNextHopAddrType. |
| 1.3.6.1.2.1.10.166.4.2 | NodemplsLdpConformance | |||
| 1.3.6.1.2.1.10.166.4.2.1 | NodemplsLdpGroups | |||
| 1.3.6.1.2.1.10.166.4.2.1.1 | GroupmplsLdpGeneralGroup | current | Objects that apply to all MPLS LDP implementations. | |
| 1.3.6.1.2.1.10.166.4.2.1.2 | GroupmplsLdpLspGroup | current | These objects are for LDP implementations which interface to the Label Information Base (LIB) in the MPLS-LSR-STD-MIB. The LIB is represented in the mplsInSegm… | |
| 1.3.6.1.2.1.10.166.4.2.1.3 | GroupmplsLdpNotificationsGroup | current | The notification for an MPLS LDP implementation. | |
| 1.3.6.1.2.1.10.166.4.2.2 | NodemplsLdpCompliances | |||
| 1.3.6.1.2.1.10.166.4.2.2.1 | CompliancemplsLdpModuleFullCompliance | current | The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-C… | |
| 1.3.6.1.2.1.10.166.4.2.2.2 | CompliancemplsLdpModuleReadOnlyCompliance | read-only | current | The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE. |