RAD-Ipmux-MIB
178 objects
IPMUX MIB.
Imported Objects
| IF-MIB | ifAlias |
| RAD-GEN-MIB | agnLed |
| RAD-NtePrtCo-MIB | atmInterfaceAlarmStatus |
| RAD-SMI-MIB | diverseIfWanGen radSysWanEvents |
| SNMPv2-SMI | Counter32 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.3.1.6.7 | Identityip2If | IPMUX MIB. | ||
| 1.3.6.1.4.1.164.3.1.6.7.1 | Tableip2IfTable | not-accessible | current | Channels Configuration Table. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1 | Rowip2IfEntry | not-accessible | current | Application layer configuration per link |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.1 | Columnip2IfChannelIndex | read-only | current | The channel index, which is actualy the bundle ID. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.2 | Columnip2IfRowStatus | read-create | current | This parameter allows NMS to create/delete entries of this table. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.3 | Columnip2IfOperStatus | read-only | current | The actual link status. remoteFail - No Rx. localFail - No Tx. unavailable - No echo replay or replay with invalid code or when connection is in Test state. va… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.4 | Columnip2IfAdminStatus | read-create | current | The desired state of the link. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.5 | Columnip2IfDestAddr | read-create | current | The destination IP address. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.6 | Columnip2IfNextHop | read-create | current | The next hop to which the frame should be sent. Default value - 0.0.0.0. Upon setting the default value the frame is sent to the default Gateway. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.7 | Columnip2IfDestPort | read-create | current | The destination Bundle at the far-end device. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.8 | Columnip2IfMacAddr | read-create | current | The Destination MAC address of the next hop or destination station. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.9 | Columnip2IfJitterBuffer | read-create | current | The maximum cell arrival jitter in 10 usec that the reassembly process will tolerate in the cell stream, without producing errors on the CBR service interface.… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.10 | Columnip2IfTos | read-create | current | The TOS (Type of Service) value: 0..255. In Vmux-2100/110 devices versions 3.1 and up, in Vmux-210 and in Vmux-4x0: LSB 8 bits - 00 00 00 XX will be used for S… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.11 | Columnip2IfTDMBytesInFrame | read-create | current | The number of TDM bytes to be placed in a single IP frame payload. For ip2IfTDMoIpMode = cesOverPsn this parameter indicates the number of IP frames, calculate… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.12 | Columnip2IfVlanSupport | read-create | current | VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.13 | Columnip2IfVlanIdentifier | read-create | current | VLAN ID. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.14 | Columnip2IfVlanFramePriority | read-create | current | VLAN Frame priority. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.15 | Columnip2IfExitPort | read-create | current | This object determines to which external port the traffic will be sent. auto - the device will decide automatically the exit port. If there is an option for Tx… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.16 | Columnip2IfVoiceOos | read-create | current | Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.17 | Columnip2IfDataOos | read-create | current | Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.18 | Columnip2IfBundleUsage | read-only | current | The Bundle Resource usage in Kbps. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.19 | Columnip2IfOAM | read-create | current | This parameter determine the OAM configuration. The LSB (Bit 0 the most right one) is used for OAM connectivity. Values: 0 = disable, 1= enable. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.20 | Columnip2IfTDMoIpMode | read-create | current | The TDMoIP Mode configuration. Static- means TS can Tx any time. dynamicLES - means TS can Tx only when line is enabled according to LES protocol. dynamicCAS -… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.21 | Columnip2IfTimeElapsed | read-only | current | The number of seconds that have elapsed since the beginning of the current error-measurement period. If, for some reason, such as an adjustment in the system's… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.22 | Columnip2IfValidIntervals | read-only | current | The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.23 | Columnip2IfFarEndType | read-create | current | This object defines the type of the Far-End device. This data is important for signaling and DS0 format. For Vmux: e1 (2) value is used for a PBX in the Far En… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.24 | Columnip2IfRdnState | read-only | current | This object defines the role this bundle plays in the redundancy scheme: none(2) - means this bundle is not part of redundancy pair. primary/ secondary - means… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.25 | Columnip2IfSourceAddr | read-create | current | Source IP Address of the bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.26 | Columnip2IfBandWidth | read-create | current | Defines the Bandwidth of the bundle. For TDM bundles - it is the Number of Time Slots in The Bundle. - For T1 the value will be: 1..24 - For E1 the value will … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.27 | Columnip2IfMeasuredSilence | read-only | current | This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. De… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.28 | Columnip2IfPayloadType | read-create | current | This object defines the TDMoIP payload type. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.29 | Columnip2IfProtocolVersion | read-create | current | This object defines the TDMoIP protocol Version. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.30 | Columnip2IfTdmBackUpNextHop | read-create | current | Defines the TDM bundle default router in case there was a switch from the Primary Link (for example an ETH port) to a TDM backup Link like E1, T1 or Serial Lin… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.31 | Columnip2IfOosTxEnable | read-create | current | This object defines whether OOS will be Transmitted. Note that for IPmux1000 the Lbit is always sent, but the OOS will be sent according to user selection in t… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.32 | Columnip2IfConnCheckPktFrequency | read-create | current | Time in sec. between 2 Bundle Connectivity Check packets. Valid values: 0..60. 0 = Not Applicable. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.33 | Columnip2IfConnPktTimeOutCycles | read-create | current | No. of cycles the agent will send Bundle Connectivity packets without receiving a response from the remote device before declaring that the bundle connection t… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.34 | Columnip2IfMfRelay | read-create | current | Multi Frequency Signaling Detection. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.35 | Columnip2IfTxGain | read-create | current | Transmit gain in dBm. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.36 | Columnip2IfSuperTandem | read-create | current | The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.37 | Columnip2IfSrcPort | read-create | current | The source Bundle at the local device, this parameter used for cases where there is no match between ip2IfChannelIndex and the Source Bundle ID. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.38 | Columnip2IfModemCalls | read-create | current | This MIB object shows whether Modem Calls are enabled via the bundle. relay option (3) means that the bundle will send to the network only modulated data. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.39 | Columnip2IfMinPulseWidth | read-create | current | Indicates the minimum width in milliseconds of the MF (Multi Frequency) tone transmitted by the switch. Valid values: 45-300 msec. notApplicable=0. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.40 | Columnip2IfMinPowerLevel | read-create | current | Indicates the minimum power level in dBm of the MF (Multi Frequency) tone transmitted by the switch. Valid values: -1...-35 dBm. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.41 | Columnip2IfEchoCanceler | read-create | current | Echo canceler activation. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.42 | Columnip2IfCodingLaw | read-create | current | This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.43 | Columnip2IfCustomToneDetect | read-create | current | Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector. This tone is sent between PBX devices in order to check that the line status is OK.… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.44 | Columnip2IfCallerIdDelay | read-create | current | Time in msec between CLID (Caller ID) signal detection on the line and CLID signal transmission. The CLID must be sent between ringing signals and the value of… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.45 | Columnip2IfConnectivityMode | read-create | current | This MIB object shows whether to send Pings or OAM frames over the bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.46 | Columnip2IfClockSourceEnable | read-create | current | This MIB object defines whether this bundle can be a clock source. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.47 | Columnip2IfNetworkType | read-create | current | This MIB object defines the network over which the Bundle PSN (Packet Switching Network)is transported. In Gmux2000: ipComprHeader indicates proprietary compre… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.48 | Columnip2IfMplsRxLabelEnable | read-create | current | This MIB object defines whether there is user defined inner (Rx.) label for this Bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.49 | Columnip2IfMplsRxLabel | read-create | current | This MIB object defines the MPLS Rx. Label for this Bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.50 | Columnip2IfMplsTxLabelEnable | read-create | current | This MIB object defines whether there is user defined outer (Tx.) label for this Bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.51 | Columnip2IfMplsTxLabel | read-create | current | This MIB object defines the MPLS Tx. Label for this Bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.52 | Columnip2IfMplsTxExpBits | read-create | current | The MPLS Network priority (EXP bits) used for this bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.53 | Columnip2IfMfcSpoofing | read-create | current | This MIB object defines whether the MFC (Multi Frequency Compelled) protocol spoofing will exist in the bundle. When the MFC Spoofing is used, the Local and Re… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.54 | Columnip2IfToneAckInterval | read-create | current | Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until it receives an acknowledgement from this PBX. Valid values: 60...400 in s… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.55 | Columnip2IfNextHopType | read-create | current | This MIB object defines the Bundle next Hop Address Type. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.56 | Columnip2IfNoiseLevelForVAD | read-create | current | This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to handle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.57 | Columnip2IfClockPreferences | read-create | current | The Clock preferences: accurateness (2) = Accurate clock is more important than Constant Delay. constantDelay (3)= Constant Delay is more important than Accura… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.58 | Columnip2IfConnectionMode | read-create | current | The Connection Mode: tdmOIpCe (2) = TDMOiP (CE) = Circuit Emulation. tdmOIpCv (3)= TDMOiP (CV) = Compressed Voice. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.59 | Columnip2IfRingBack | read-create | current | Enables or disable Ring Back. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.60 | Columnip2IfReversePolarity | read-create | current | Enables or disable Reverse polarity synthesis. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.61 | Columnip2IfPulseMeter | read-create | current | Enables or disable Pulse metering synthesis. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.62 | Columnip2IfPulseMeterFreq | read-create | current | Frequency of synthesized pulse metering for this bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.63 | Columnip2IfPulseMeterPeriod | read-create | current | Duration of synthesized pulse metering. current values are: 100-250. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.64 | Columnip2IfOnHookDetect | read-create | current | Enables or disable immediate reaction to On-Hook bits from network in Ringing. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.65 | Columnip2IfComfortNoiseGen | read-create | current | Enable or disable Comfort Noise Generation (CNG). When this parameter is enabled and no voice payload exists on the line for some time period during the call (… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.66 | Columnip2IfExitChannel | read-create | current | The channelized bundle that the voice bundle exits through. In Gmux2000 it is the ifIndex of the Channelized Bundle (sub-channel) that the Voice Bundle exits t… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.67 | Columnip2IfMaxVBDModemCalls | read-create | current | Maximum VBD modem calls for this bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.68 | Columnip2IfMaxRelayModemCalls | read-create | current | Maximum Relay modem calls for this bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.69 | Columnip2IfCustomToneFrequency | read-create | current | This is the frequency of the Custom Tone that is sent between PBXs in order to check that the line status is OK. When the Custom Tone Detection is enabled the … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.70 | Columnip2IfVadMethod | read-create | current | Voice Activity Detection (VAD) method. proprietary (2) - non standard VAD based only on power measurement. It is very sensitive to background noise. internalIT… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.71 | Columnip2IfRxGain | read-create | current | Receive gain in dBm. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.72 | Columnip2IfCallerIDType | read-create | current | Caller ID Type used by the DSP for this bundle. Bellcore type is used by the American method. V.23 type is used by the European method. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.73 | Columnip2IfPeerAddrType | read-create | current | This MIB object defines the peer Address Type. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.74 | Columnip2IfVbdRate | read-create | current | Voice Band Data (VBD) rate for this bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.75 | Columnip2IfDtmfDetection | read-create | current | Enable/Disable DTMF (Dual Tone Multi Frequency) detectors for this bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.76 | Columnip2IfNlpCutoffLevel | read-create | current | Non Linear Processor (NLP) Cutoff Level for this bundle. This parameter is used by the echo canceller. It is the maximum absolute linear PCM amplitude of the n… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.77 | Columnip2IfDtdErlRatioCutoffQ3 | read-create | current | The DTD ERL cutoff level is used in order to determine whether the near-end is talking or not. This parameter is used by the echo canceller when echo exists an… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.78 | Columnip2IfCASRedundancy | read-create | current | Enable/Disable CAS signaling redundancy. This parameter is useful when there are problems with the network and applicable only for CAS signaling: E1-MF (G.732S… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.79 | Columnip2IfBundleSensitivity | read-create | current | Denotes if the bundle is sensitive to delay in the network, or is sensitive to data errors in the network. Voice bundles are sensitive to delay; Non-voice bund… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.80 | Columnip2IfOAMBundleIdent | read-create | current | Denotes if an OAM bundle is identified according to the Bundle Number (0x3fff), or according to the value of the first nibble in the VCCV control word sent in … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.81 | Columnip2IfMaxTxQueue | read-create | current | Max Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.82 | Columnip2IfMaxGprsTxQueue | read-create | current | Max GPRS Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packet… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.83 | Columnip2IfV23HD | read-create | current | This parameter shows whether V.23 Half Duplex Modem Protocol is enabled on the bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.84 | Columnip2IfModemProtocolMode | read-create | current | This octet string contains the mode of each Modem Protocol used on the bundle. For each protocol one octet will be used. Octet #1 will be used for V.22 Protoco… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.85 | Columnip2IfCdisCngDetectionTime | read-create | current | When working with CDIS (Call DIScrimination method) or CNG (Comfort Noise Generation): The time in msec that the device will detect 1100Hz & 2100Hz signals on … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.86 | Columnip2IfSuperTandemBitMask | read-create | current | This MIB object enables controlling the Time Slot/Channel rate. Valid values: 1 - FF HEX Each BIT represents 1/8 of the TS. Example: 7E (0111 1110) means that … |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.87 | Columnip2IfVbdSwitchbackTime | read-create | current | Time in msec required for the DSP to switch back from VBD (Voice Band Data) to Voice. For Vmux: the values will be in steps of 30 msec. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.88 | Columnip2IfCallerIdTxGain | read-create | current | The gain value in dBm units used for transmitting the Caller ID signal on the bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.89 | Columnip2IfCallerIdRxGain | read-create | current | The gain value in dBm units of the Caller ID signal received on the bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.90 | Columnip2IfUdpMuxMethod | read-create | current | This parameter determines according to which field the multiplexing is made: srcPort (2) - multiplexing according to the UDP Source Port (Dest=0x085e). This sh… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.91 | Columnip2IfCallerIdDetection | read-create | current | Enable/Disable Caller ID Detection for this bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.92 | Columnip2IfWap | read-create | current | Enable/Disable WAP (Wireless Application Protocol) for this bundle. WAP allows users to access the internet from wireless devices. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.93 | Columnip2IfSignalingOos | read-create | current | Out of Service code sent on signaling TimeSlot. |
| 1.3.6.1.4.1.164.3.1.6.7.2 | Scalarip2IfTDMFrameBytes | read-write | current | The number of TDM bytes to be placed in a single IP frame payload. |
| 1.3.6.1.4.1.164.3.1.6.7.3 | Scalarip2IfTosValue | read-write | current | The TOS value to write in the IP frame. |
| 1.3.6.1.4.1.164.3.1.6.7.4 | Scalarip2IfVlanTagging | read-write | current | VLAN support. no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame. |
| 1.3.6.1.4.1.164.3.1.6.7.5 | Scalarip2IfVlanID | read-write | current | VLAN ID. |
| 1.3.6.1.4.1.164.3.1.6.7.6 | Scalarip2IfVlanPriority | read-write | current | Frame priority. |
| 1.3.6.1.4.1.164.3.1.6.7.7 | Tableip2IfStatTable | not-accessible | current | Channels (Bundles) Statistics Table. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1 | Rowip2IfStatEntry | not-accessible | current | IP Statistics per bundle |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.1 | Columnip2IfStatChIndex | read-only | current | The channel index, which is actualy the bundle ID. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.2 | Columnip2IfStatSeqErrors | read-only | current | Number of events that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.3 | Columnip2IfStatBufUnderflows | read-only | current | Number of events that the buffer underflows. This records the count of the number of events the Receive (Eth to TDM) buffer underflows. In the case of a contin… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.4 | Columnip2IfStatBufOverflows | read-only | current | Number of events that the buffer overflows. This records the count of the number of events the Receive (Eth to TDM) buffer overflows. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.5 | Columnip2IfStatTxOnTimeInterval | read-only | current | Number of frames that were transmitted due to time interval elapse. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing ti… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.6 | Columnip2IfStatTxOnMaxSize | read-only | current | Number of frames that were transmitted due to reaching max. frame size. The user can choose to Tx the Frame when it reaches the Max size or when the packetizin… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.7 | Columnip2IfStatRxSignaling | read-only | current | Number of signaling frames that were received. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.8 | Columnip2IfStatRxVoice | read-only | current | Number of voice frames that were received. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.9 | Columnip2IfStatRxHdlc | read-only | current | Number of HDLC frames that were received. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.10 | Columnip2IfStatTxSignaling | read-only | current | Number of signaling frames that were transmitted. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.11 | Columnip2IfStatTxVoice | read-only | current | Number of voice frames that were transmitted. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.12 | Columnip2IfStatTxHdlc | read-only | current | Number of HDLC frames that were transmitted. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.13 | Columnip2IfStatRdnFlip | read-only | current | Number of redundancy flips occured. This parameter counts only flips from this bundle to the other bundle in the redundancy couple. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.14 | Columnip2IfFarEndTdmStatus | read-only | current | This variable indicates the Status of the Far-End TDM Line. It contains failure state information. The variable is a bit map represented as a sum, therefore, i… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.15 | Columnip2IfStatPsnTxFrames | read-only | current | Number of frames that were transmitted to PSN. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.16 | Columnip2IfStatPsnRxFrames | read-only | current | Number of frames that were recieved from PSN. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.17 | Columnip2IfStatMinJittBufLevel | read-only | current | The Minimum jitter buffer level (in msec). |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.18 | Columnip2IfStatMaxJittBufLevel | read-only | current | The Maximum jitter buffer level (in msec). |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.19 | Columnip2IfStatRecommendedJittBufSize | read-only | current | The Recommended jitter buffer Size (in msec). 0= not applicable. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.20 | Columnip2IfStatPsnSeqErrors | read-only | current | Number of times that the sequence number of an incoming Frame indicates Loss of Frame or Out of order occured in PSN. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.21 | Columnip2IfStatPsnReorderFrames | read-only | current | Number of times that Frames had been reordered in PSN. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.22 | Columnip2IfStatMinRoundTripDelay | read-only | current | The minimum Round Trip delay (in msec). 0= not applicable. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.23 | Columnip2IfStatMaxRoundTripDelay | read-only | current | The maximum Round Trip delay (in msec). 0= not applicable. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.24 | Columnip2IfStatAvrRoundTripDelay | read-only | current | The avarage Round Trip delay (in msec). 0= not applicable. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.25 | Columnip2IfStatFrameTrackDupDrop | read-only | current | The number of packets dropped due to being duplicated. (duplicated packet means a packet that has the same sequential number as a packet being received previou… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.26 | Columnip2IfStatFrameTrackMissing | read-only | current | The number of packets that are missing. (Missing packet means an expected packet- according to the current sequential number - that was not received). |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.27 | Columnip2IfStatFrameTrackLongSerMiss | read-only | current | The longest series of consecutive missing sequential numbers. Missing sequential numbers represent missing packets that was expected to be received successivel… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.28 | Columnip2IfStatTxMeasuredSilence | read-only | current | This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. De… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.29 | Columnip2IfStatRxMeasuredSilence | read-only | current | This object shows the percentage of Silence that was measured by the device for the current bundle in the received payload. Relevant values: 0..100, 255. Defau… |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.30 | Columnip2IfStatHdlcCrcErr | read-only | current | This counter indicates the number of received HDLC frames with CRC errors. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.31 | Columnip2IfStatHdlcAlignErr | read-only | current | This counter indicates the number of received HDLC frames with alignment errors. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.32 | Columnip2IfStatHdlcOversize | read-only | current | This counter indicates the number of received HDLC frames longer than 1470. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.33 | Columnip2IfStatHdlcUndersize | read-only | current | This counter indicates the number of received HDLC frames shorter than 4. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.34 | Columnip2IfStatHdlcAbort | read-only | current | This counter indicates the number of received HDLC frames with abort indication. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.35 | Columnip2IfStatRxCorrectFrames | read-only | current | Number of received correct frames. |
| 1.3.6.1.4.1.164.3.1.6.7.7.1.36 | Columnip2IfStatHdlcErroredFrames | read-only | current | Number of received errored HDLC frames. |
| 1.3.6.1.4.1.164.3.1.6.7.8 | Scalarip2IfRateLimit | read-write | current | The maximum rate permitted to transfer via the network portin Mbps. |
| 1.3.6.1.4.1.164.3.1.6.7.9 | Tableip2IfPortTable | not-accessible | current | Port Table. |
| 1.3.6.1.4.1.164.3.1.6.7.9.1 | Rowip2IfPortEntry | not-accessible | current | Application layer configuration per Port |
| 1.3.6.1.4.1.164.3.1.6.7.9.1.1 | Columnip2IfPortIndex | read-only | current | The Port index, which is actualy the ifIndex. |
| 1.3.6.1.4.1.164.3.1.6.7.9.1.2 | Columnip2IfPortUsage | read-only | current | This parameter indicates the usage of the port (percents). |
| 1.3.6.1.4.1.164.3.1.6.7.9.1.3 | Columnip2IfPortMask | read-write | current | This parameter defines whether Agent will mask port's alarms and statistics or not. |
| 1.3.6.1.4.1.164.3.1.6.7.9.1.4 | Columnip2IfPortTotalThroughput | read-only | current | This parameter indicates the total Throughput of the port in bps. |
| 1.3.6.1.4.1.164.3.1.6.7.10 | Tableip2IfCurrentStatTable | not-accessible | current | Channels (Bundles) Current Statistics Table. |
| 1.3.6.1.4.1.164.3.1.6.7.10.1 | Rowip2IfCurrentStatEntry | not-accessible | current | IP Current Statistics per bundle |
| 1.3.6.1.4.1.164.3.1.6.7.10.1.1 | Columnip2IfCurrentStatSeqErrors | read-only | current | Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the current interva… |
| 1.3.6.1.4.1.164.3.1.6.7.10.1.2 | Columnip2IfCurrentStatBufUnderflows | read-only | current | Number of seconds that the buffer underflows in the current interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflow… |
| 1.3.6.1.4.1.164.3.1.6.7.10.1.3 | Columnip2IfCurrentStatBufOverflows | read-only | current | Number of seconds that the buffer overflows in the current interval. This records the count of the number of seonds the Receive (Eth to TDM) buffer overflows i… |
| 1.3.6.1.4.1.164.3.1.6.7.10.1.4 | Columnip2IfCurrentStatMaxDelayVar | read-only | current | The maximum deviation from the center of the buffer (in msec) for the current interval. |
| 1.3.6.1.4.1.164.3.1.6.7.10.1.5 | Columnip2IfCurrentStatMinJittBufLevel | read-only | current | The Minimum jitter buffer level (in msec) for the current interval. |
| 1.3.6.1.4.1.164.3.1.6.7.10.1.6 | Columnip2IfCurrentStatMaxJittBufLevel | read-only | current | The Maximum jitter buffer level (in msec) for the current interval. |
| 1.3.6.1.4.1.164.3.1.6.7.10.1.7 | Columnip2IfCurrentStatTxErrFrameSec | read-only | current | The number of seconds in which errored frames were transmitted during the current interval. The error may be one of the following: CRC error, Alignment error, … |
| 1.3.6.1.4.1.164.3.1.6.7.11 | Tableip2IfIntervalStatTable | not-accessible | current | Channels (Bundles) Interval Statistics Table. |
| 1.3.6.1.4.1.164.3.1.6.7.11.1 | Rowip2IfIntervalStatEntry | not-accessible | current | IP Interval Statistics per bundle |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.1 | Columnip2IfIntervalStatIndex | read-only | current | The Interval index, which is actualy the Interval number. |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.2 | Columnip2IfIntervalStatSeqErrors | read-only | current | Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the selected interv… |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.3 | Columnip2IfIntervalStatBufUnderflows | read-only | current | Number of seconds that the buffer underflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflo… |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.4 | Columnip2IfIntervalStatBufOverflows | read-only | current | Number of seconds that the buffer overflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer overflows… |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.5 | Columnip2IfIntervalStatMaxDelayVar | read-only | current | The maximum size of the buffer (in 10's of usec) in the selected interval. For some devices (e.g. MP-4100) units are usec. |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.6 | Columnip2IfIntervalStatMinJittBufLevel | read-only | current | The Minimum jitter buffer level (in msec) for the selected interval. For some devices (e.g. MP-4100) units are usec. |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.7 | Columnip2IfIntervalStatMaxJittBufLevel | read-only | current | The Maximum jitter buffer level (in msec) for the selected interval. For some devices (e.g. MP-4100) units are usec. |
| 1.3.6.1.4.1.164.3.1.6.7.11.1.8 | Columnip2IfIntervalStatTxErrFrameSec | read-only | current | The number of seconds in which errored frames were transmitted during the selected interval. The error may be one of the following: CRC error, Alignment error,… |
| 1.3.6.1.4.1.164.3.1.6.7.12 | Scalarip2IfLogEvents | read-write | current | This parameter defines whether all Jitter Buffer and Sequence Number events will enter to Log File, or enter those events to Log file in one minute steps. |
| 1.3.6.1.4.1.164.3.1.6.7.13 | Scalarip2IfEthSwitchMode | read-write | current | This parameter defines whether Eth Switch is in VLAN Tagged mode. |
| 1.3.6.1.4.1.164.6.1.3.0.5 | NotificationalarmStatusTrap | current | The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm. | |
| 1.3.6.1.4.1.164.6.1.3.0.6 | NotificationsystemTrap | current | This trap alerts of major problems in the device. | |
| 1.3.6.1.4.1.164.6.1.3.0.7 | NotificationalarmLOS | current | This trap indicates Loss Of Signal. | |
| 1.3.6.1.4.1.164.6.1.3.0.8 | NotificationalarmLOF | current | This trap indicates Loss Of Frame. | |
| 1.3.6.1.4.1.164.6.1.3.0.9 | NotificationchannelOperStatusTrap | current | This trap is sent upon any change in one or more channels. | |
| 1.3.6.1.4.1.164.6.1.3.0.10 | NotificationalarmAIS | current | This trap indicates AIS. | |
| 1.3.6.1.4.1.164.6.1.3.0.11 | NotificationalarmRDI | current | This trap indicates RDI. | |
| 1.3.6.1.4.1.164.6.1.3.0.12 | NotificationalarmFEBE | current | This trap indicates FEBE. | |
| 1.3.6.1.4.1.164.6.1.3.0.13 | NotificationlocalConnStatusTrap | current | This trap is sent upon a change in Local connectivity of Bundle connection. | |
| 1.3.6.1.4.1.164.6.1.3.0.14 | NotificationremoteConnStatusTrap | current | This trap is sent upon a change in Remote connectivity of Bundle connection. | |
| 1.3.6.1.4.1.164.6.1.3.0.15 | NotificationbundleConnectionStatusTrap | current | This trap is sent upon any change in the connectivity status of a Bundle (ip2IfOperStatus). The ifAlias index is the ifIndex of the bundle that its status has … |