RAD-L3SAT-MIB
142 objects
L3 SAT MIB.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.6.1.15.0.50 | NotificationsystemL3SatTestStart | current | This trap indicates that a L3 SAT test was started. | |
| 1.3.6.1.4.1.164.6.1.15.0.51 | NotificationsystemL3SatConfigurationTestEnd | current | This trap indicates that a L3 SAT configuration phase has ended. | |
| 1.3.6.1.4.1.164.6.1.15.0.52 | NotificationsystemL3SatPerformanceTestEnd | current | This trap indicates that a L3 SAT performance phase has ended. | |
| 1.3.6.1.4.1.164.6.1.15.0.53 | NotificationsystemL3SatResponderActivated | current | This trap indicates that a L3 SAT responder was activated. | |
| 1.3.6.1.4.1.164.6.1.15.0.54 | NotificationsystemL3SatResponderDeactivated | current | This trap indicates that a L3 SAT responder was deactivated (either by the operator or by the device due to external conditions). | |
| 1.3.6.1.4.1.164.6.1.15.0.55 | NotificationsystemL3SatPreliminaryTestFailed | current | This trap indicates a failure in one of the L3 SAT preliminary tests. | |
| 1.3.6.1.4.1.164.6.1.15.1.6 | Tablel3SatPeerProfileTable | not-accessible | current | This table contains peer configuration profiles to be used in L3 SATs. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1 | Rowl3SatPeerProfileEntry | not-accessible | current | An entry in peer profile table. A row cannot be deleted if the profile is associated to a peer. A row cannot be modified if the profile is associated to a peer… |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.1 | Columnl3SatPeerProfileName | not-accessible | current | A meaningful printable profile name. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.2 | Columnl3SatPeerProfileRowStatus | read-create | current | This object enables creation and deletion of profiles. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.3 | Columnl3SatPeerProfileL4Port | read-create | current | The start of the range of UDP ports that are used in the tests. Must be a multiple of 16. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.4 | Columnl3SatPeerProfileScope | read-create | current | The scope of the test: configuration phase, performance phase, or both phases. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.5 | Columnl3SatPeerProfilePolicingTest | read-create | current | Allows to include or exclude the traffic policing sub-test from the configuration phase. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.6 | Columnl3SatPeerProfileBwSteps | read-create | current | The transmission rate in each step of the step load sub-test, configurable as percentage of BW. The last transmission rate must be 100% BW therefore only up to… |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.7 | Columnl3SatPeerProfileConfDuration | read-create | current | The duration of the configuration phase. This duration is used for each test session. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.8 | Columnl3SatPeerProfilePerfDuration | read-create | current | The duration of the performance phase. |
| 1.3.6.1.4.1.164.6.1.15.1.6.1.9 | Columnl3SatPeerProfileReportType | read-create | current | Indicates which metrics are included in the report. Based on this configuration, each metric in the l3SatReportTable is either valid or not as stated in the me… |
| 1.3.6.1.4.1.164.6.1.15.1.7 | Tablel3SatSessionProfileTable | not-accessible | current | This table contains test session configuration profiles to be used in L3 SATs. |
| 1.3.6.1.4.1.164.6.1.15.1.7.1 | Rowl3SatSessionProfileEntry | not-accessible | current | An entry in test session profile table. A row cannot be deleted if the profile is associated to a test session. A row cannot be modified if the profile is asso… |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.1 | Columnl3SatSessionProfileName | not-accessible | current | A meaningful printable profile name. |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.2 | Columnl3SatSessionProfileRowStatus | read-create | current | This object enables creation and deletion of profiles. |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.3 | Columnl3SatSessionProfileIpSize | read-create | current | The size of test packets. Up to 4 different packet sizes shall be selected. This size refers only to the IP part (IP header + UDP header + payload) and does no… |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.4 | Columnl3SatSessionProfileIpCustomSize | read-create | current | A user configurable packet size to be used in the tests. Relevant only when the ipCustomVal(8) bit is set at l3SatSessionProfileIpSize. |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.5 | Columnl3SatSessionProfilePlrThreshold | read-create | current | The service acceptance criteria for round-trip Packet Loss Ratio. |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.6 | Columnl3SatSessionProfilePtdThreshold | read-create | current | The service acceptance criteria for round-trip/one-way Packet Transfer Delay. |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.7 | Columnl3SatSessionProfilePdvThreshold | read-create | current | The service acceptance criteria for round-trip/one-way Packet Delay Variation. |
| 1.3.6.1.4.1.164.6.1.15.1.7.1.8 | Columnl3SatSessionProfileAvailThreshold | read-create | current | The service acceptance criteria for round-trip Availability. |
| 1.3.6.1.4.1.164.6.1.15.2.11 | Tablel3SatGeneratorTable | not-accessible | current | This table contains a list of generator entities used in L3 SATs. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1 | Rowl3SatGeneratorEntry | not-accessible | current | An entry in L3 SAT generator table. A row cannot be modified when the RowStatus is active(1). A row cannot be deleted while at least one of the test sessions i… |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.1 | Columnl3SatGeneratorName | not-accessible | current | A meaningful printable generator name. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.2 | Columnl3SatGeneratorRowStatus | read-create | current | This object enables creation and deletion of L3 SAT generators. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.3 | Columnl3SatGeneratorApplication | read-create | current | The role of the generator device in the service path - L3 forwarder or L2 probe. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.4 | Columnl3SatGeneratorInterface | read-create | current | The associated physical or logical port. This object is relevant only when l3SatGeneratorApplication is set to l3OverL2(2). |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.5 | Columnl3SatGeneratorOuterVlan | read-create | current | The outer VLAN tag of outgoing and incoming test and TWAMP packets. When there is no outer VLAN the value 4294967295 is used. This object is relevant only when… |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.6 | Columnl3SatGeneratorOuterPbit | read-create | current | The outer VLAN priority (P-bit) assigned to outgoing and incoming test and TWAMP packets. A value of 255 means the marking profile of l3SatGeneratorOuterMarkin… |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.7 | Columnl3SatGeneratorOuterMarkingProfile | read-create | current | The profile used to mark outer VLAN priority (P-bit) of outgoing and incoming test and TWAMP packets. The configured value is the index of the corresponding en… |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.8 | Columnl3SatGeneratorInnerVlan | read-create | current | The inner VLAN tag of outgoing and incoming test and TWAMP packets. When there is no inner VLAN the value 4294967295 is used. This object is relevant only when… |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.9 | Columnl3SatGeneratorInnerPbit | read-create | current | The inner VLAN priority (P-bit) assigned to outgoing and incoming test and TWAMP packets. This object is relevant only when l3SatGeneratorApplication is set to… |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.10 | Columnl3SatGeneratorRouterEntity | read-create | current | The number of the router under which the L3 SAT is performed. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.11 | Columnl3SatGeneratorLocalAddrType | read-create | current | The type of IP address of the L3 SAT generator. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.12 | Columnl3SatGeneratorLocalAddr | read-create | current | The IP address of the L3 SAT generator. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.13 | Columnl3SatGeneratorRouterInterface | read-only | current | The ifIndex of the associated router interface. |
| 1.3.6.1.4.1.164.6.1.15.2.11.1.14 | Columnl3SatGeneratorStatus | read-only | current | The current status of the generator: Shutdown - the generator is disabled. Idle - some of the mandatory attributes were not configured yet e.g. L2 parameters, … |
| 1.3.6.1.4.1.164.6.1.15.2.12 | Tablel3SatPeerTable | not-accessible | current | This table contains a list of peers entities used in L3 SATs. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1 | Rowl3SatPeerEntry | not-accessible | current | An entry in L3 SAT peer table. A row cannot be modified or deleted while the peer is active (indicated by l3SatPeerCurrentPhase != idle(1)). When a row is dele… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.1 | Columnl3SatPeerAddrType | not-accessible | current | The type of IP address of the L3 SAT peer. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.2 | Columnl3SatPeerAddr | not-accessible | current | The IP address of the L3 SAT peer. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.3 | Columnl3SatPeerRowStatus | read-create | current | This object enables creation and deletion of L3 SAT peers. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.4 | Columnl3SatPeerProfile | read-create | current | The profile used for the peer parameters. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.5 | Columnl3SatPeerCmd | read-create | current | A command to activate or de-activate the test at the generator side. If sanity checks prevent the test activation then a set to start(1) shall be rejected with… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.6 | Columnl3SatPeerConfChanged | read-only | current | Indication whether the configuration of the peer was changed after the test was completed. The configuration of the peer, in this context, includes the followi… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.7 | Columnl3SatPeerTimeRemaining | read-only | current | The time remaining till the end of the test. If the peer is not active a value of zero is returned. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.8 | Columnl3SatPeerCurrentPhase | read-only | current | The current phase of the test. If the peer is not active the value idle(1) is returned. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.9 | Columnl3SatPeerTodStatus | read-only | current | The current TOD synchronization state with the responder device. The value unknown(1) is returned if the generator device is connected to an NTP server but the… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.10 | Columnl3SatPeerResponderType | read-only | current | The discovered type of the responder. If the peer was never activated the value unknown(1) is returned. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.11 | Columnl3SatPeerMtu | read-only | current | The discovered IP MTU of the path to the responder. If the peer was never activated the value zero is returned. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.12 | Columnl3SatPeerStartTime | read-only | current | The date and time at the last peer activation. If the peer was never activated a null value is returned. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.13 | Columnl3SatPeerEndTime | read-only | current | The date and time when the last test was ended (regardless of the end result passed/failed/aborted). If a test is in progress or the peer was never activated a… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.14 | Columnl3SatPeerTimeElapsed | read-only | current | For an in progress test - the elapsed time of the current test. For a completed test - the duration of the last test. If the peer was never activated a zero va… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.15 | Columnl3SatPeerOutOfSyncSeconds | read-only | current | The number of seconds there was no TOD synchronization with the responder device. If the peer was never activated a zero value is returned. |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.16 | Columnl3SatPeerOverAllResult | read-only | current | The overall result of the last test. The value notApplicable(1) is returned in the following cases: - The test is currently in progress. - The peer was never a… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.17 | Columnl3SatPeerConfDuration | read-only | current | The duration of the configuration phase. This duration is used for each test session. This object is a copy of the corresponding object in the peer profile. Th… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.18 | Columnl3SatPeerPerfDuration | read-only | current | The duration of the performance phase. This object is a copy of the corresponding object in the peer profile and is used for availability calculation. The dupl… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.19 | Columnl3SatPeerScope | read-only | current | The scope of the test: configuration phase, performance phase, or both phases. This object is a copy of the corresponding object in the peer profile. The dupli… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.20 | Columnl3SatPeerConnectivityResult | read-only | current | The result of the last connectivity sub-test. The value notApplicable(1) is returned in the following cases: - The sub-test is currently in progress. - The pee… |
| 1.3.6.1.4.1.164.6.1.15.2.12.1.21 | Columnl3SatPeerMtuTestResult | read-only | current | The result of the last MTU sub-test. The value notApplicable(1) is returned in the following cases: - The sub-test is currently in progress. - The peer was nev… |
| 1.3.6.1.4.1.164.6.1.15.2.13 | Tablel3SatSessionTable | not-accessible | current | This table contains a list of test sessions used in L3 SATs. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1 | Rowl3SatSessionEntry | not-accessible | current | An entry in L3 SAT session table. A row may be created while the peer is active (indicated by l3SatPeerCurrentPhase != idle(1)). A row cannot be modified while… |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.1 | Columnl3SatSessionName | not-accessible | current | A meaningful printable test session name. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.2 | Columnl3SatSessionRowStatus | read-create | current | This object enables creation and deletion of L3 SAT test session. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.3 | Columnl3SatSessionProfile | read-create | current | The profile used for the test session parameters. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.4 | Columnl3SatSessionBw | read-create | current | The rate of the test session traffic. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.5 | Columnl3SatSessionDscp | read-create | current | The priority value for the test session traffic. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.6 | Columnl3SatSessionConfChanged | read-only | current | Indication whether the configuration of the test session was changed after the test was completed. If the configuration was changed then threshold values shoul… |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.7 | Columnl3SatSessionStatus | read-only | current | The current status of the test session: Idle - the generator is in status shutdown(1) or idle(2). Ready - waiting for activation of the peer. In progress - the… |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.8 | Columnl3SatSessionLmSrcPort | read-only | current | The L4 source port of the loss measurement stream. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.9 | Columnl3SatSessionLmDstPort | read-only | current | The L4 destination port of the loss measurement stream. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.10 | Columnl3SatSessionDmSrcPort | read-only | current | The L4 source port of delay the measurement stream. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.11 | Columnl3SatSessionDmDstPort | read-only | current | The L4 destination port of the delay measurement stream. |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.12 | Columnl3SatSessionConfResult | read-only | current | The result of the configuration phase. The value notApplicable(1) is returned in the following cases: - The configuration phase was not performed in the last t… |
| 1.3.6.1.4.1.164.6.1.15.2.13.1.13 | Columnl3SatSessionPerfResult | read-only | current | The result of the last performance phase. The value notApplicable(1) is returned in the following cases: - The performance phase was not performed in the last … |
| 1.3.6.1.4.1.164.6.1.15.2.14 | Tablel3SatResponderTable | not-accessible | current | This table contains a list of responder entities used in L3 SATs. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1 | Rowl3SatResponderEntry | not-accessible | current | An entry in L3 SAT responder table. A row cannot be modified when the RowStatus is active(1). |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.1 | Columnl3SatResponderName | read-create | current | A meaningful printable responder name. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.2 | Columnl3SatResponderRowStatus | read-create | current | This object enables creation and deletion of L3 SAT responders. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.3 | Columnl3SatResponderApplication | read-create | current | The role of the responder device in the service path - L3 forwarder or L2 probe. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.4 | Columnl3SatResponderInterface | read-create | current | The associated physical or logical port. This object is relevant only when l3SatResponderApplication is set to l3OverL2(2). |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.5 | Columnl3SatResponderOuterVlan | read-create | current | The outer VLAN tag of outgoing and incoming test and TWAMP packets. When there is no outer VLAN the value 4294967295 is used. This object is relevant only when… |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.6 | Columnl3SatResponderOuterPbit | read-create | current | The outer VLAN priority (P-bit) assigned to outgoing and incoming test and TWAMP packets. A value of 255 means the marking profile of l3SatResponderOuterMarkin… |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.7 | Columnl3SatResponderOuterMarkingProfile | read-create | current | The profile used to mark outer VLAN priority (P-bit) of outgoing and incoming test and TWAMP packets. The configured value is the index of the corresponding en… |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.8 | Columnl3SatResponderInnerVlan | read-create | current | The inner VLAN tag of outgoing and incoming test and TWAMP packets. When there is no inner VLAN the value 4294967295 is used. This object is relevant only when… |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.9 | Columnl3SatResponderInnerPbit | read-create | current | The inner VLAN priority (P-bit) assigned to outgoing and incoming test and TWAMP packets. This object is relevant only when l3SatResponderApplication is set to… |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.10 | Columnl3SatResponderRouterEntity | read-create | current | The number of the router under which the L3 SAT is performed. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.11 | Columnl3SatResponderLocalAddrType | read-create | current | The type of IP address of the L3 SAT responder. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.12 | Columnl3SatResponderLocalAddr | read-create | current | The IP address of the L3 SAT responder. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.13 | Columnl3SatResponderL4Port | read-create | current | The start of the range of UDP ports that are used in the tests. Must be a multiple of 16. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.14 | Columnl3SatResponderRouterInterface | read-only | current | The ifIndex of the associated router interface. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.15 | Columnl3SatResponderStatus | read-only | current | The current status of the generator: Shutdown - the responder is disabled. Idle - some of the mandatory attributes were not configured yet e.g. L2 parameters, … |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.16 | Columnl3SatResponderLmRxPackets | read-only | current | The total number of packets received on all loss measurement streams. |
| 1.3.6.1.4.1.164.6.1.15.2.14.1.17 | Columnl3SatResponderDmRxPackets | read-only | current | The total number of packets received on all delay measurement streams. |
| 1.3.6.1.4.1.164.6.1.15.3.11 | Tablel3SatReportTable | not-accessible | current | This table holds the measurements and results for each L3 SAT session that was performed. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1 | Rowl3SatReportEntry | not-accessible | current | An entry in L3 SAT report table. Rows are automatically created when the corresponding peer in the l3SatPeerTable is successfully activated - for details, see … |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.1 | Columnl3SatReportIpSize | not-accessible | current | The IP size index of the report. Allows holding measurements and result per IP size. One entry for each set IP size in the corresponding l3SatSessionProfileIpS… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.2 | Columnl3SatReportTestType | not-accessible | current | The sub-test type index of the report. Allows holding measurements and result per sub-test type. Entries are created according to the associated configuration … |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.3 | Columnl3SatReportResult | read-only | current | The result of the sub-test. The initial value is notApplicable(1). Upon completion of the sub-test the value changes to passed(2) or failed(3). If the test is … |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.4 | Columnl3SatReportTxRate | read-only | current | The transmission rate that the generator was configured to in the sub-test. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.5 | Columnl3SatReportIrAverage | read-only | current | The average calculated information rate. The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.6 | Columnl3SatReportTxPackets | read-only | current | The number of transmitted packets. The initial value is one. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.7 | Columnl3SatReportLostPackets | read-only | current | The number of packets lost. The PLR is calculated by: (l3SatReportLostPackets / l3SatReportTxPackets) The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.8 | Columnl3SatReportUas | read-only | current | The number of unavailable seconds. This object is relevant only for the performance test. For the other test type entries the value is zero. The initial value … |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.9 | Columnl3SatReportAvailability | read-only | current | The percentage of available time. The availability is calculated by: (60*l3SatPeerPerfDuration - l3SatReportUas) * 10000 / (60*l3SatPeerPerfDuration) This obje… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.10 | Columnl3SatReportPtdMin | read-only | current | The minimum measured packet transfer delay. The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.11 | Columnl3SatReportPtdAverage | read-only | current | The average calculated packet transfer delay. The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.12 | Columnl3SatReportPtdMax | read-only | current | The maximum measured packet transfer delay. The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.13 | Columnl3SatReportPtdStd | read-only | current | The calculated standard deviation of the packet transfer delay. The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.14 | Columnl3SatReportPdvAverage | read-only | current | The average calculated packet delay variation. The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.15 | Columnl3SatReportPdvMax | read-only | current | The maximum calculated packet delay variation. The initial value is zero. |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.16 | Columnl3SatReportIpdvAverageFwd | read-only | current | The average calculated forward inter-packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4). For the other res… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.17 | Columnl3SatReportIpdvMaxFwd | read-only | current | The maximum calculated forward inter-packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4). For the other res… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.18 | Columnl3SatReportIpdvAverageBck | read-only | current | The average calculated backward inter-packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4). For the other re… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.19 | Columnl3SatReportIpdvMaxBck | read-only | current | The maximum calculated backward inter-packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4). For the other re… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.20 | Columnl3SatReportDuplicatedPacketsFwd | read-only | current | The number of duplicated packets in the forward direction. This object is relevant only for the performance test and only when l3SatPeerResponderType is loopAn… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.21 | Columnl3SatReportDuplicatedPacketsBck | read-only | current | The number of duplicated packets in the backward direction. This object is relevant only for the performance test and only when l3SatPeerResponderType is loopA… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.22 | Columnl3SatReportReorderedPacketsFwd | read-only | current | The number of reordered packets in the forward direction. This object is relevant only for the performance test and only when l3SatPeerResponderType is loopAnd… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.23 | Columnl3SatReportReorderedPacketsBck | read-only | current | The number of reordered packets in the backward direction. This object is relevant only for the performance test and only when l3SatPeerResponderType is loopAn… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.24 | Columnl3SatReportPtdMinFwd | read-only | current | The minimum measured forward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileReportT… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.25 | Columnl3SatReportPtdAverageFwd | read-only | current | The average calculated forward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileRepor… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.26 | Columnl3SatReportPtdMaxFwd | read-only | current | The maximum measured forward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileReportT… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.27 | Columnl3SatReportPtdStdFwd | read-only | current | The calculated standard deviation of the forward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3S… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.28 | Columnl3SatReportPtdMinBck | read-only | current | The minimum measured backward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileReport… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.29 | Columnl3SatReportPtdAverageBck | read-only | current | The average calculated backward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileRepo… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.30 | Columnl3SatReportPtdMaxBck | read-only | current | The maximum measured backward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileReport… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.31 | Columnl3SatReportPtdStdBck | read-only | current | The calculated standard deviation of the backward packet transfer delay. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.32 | Columnl3SatReportPdvAverageFwd | read-only | current | The average calculated forward packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileRepo… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.33 | Columnl3SatReportPdvMaxFwd | read-only | current | The maximum calculated forward packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileRepo… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.34 | Columnl3SatReportPdvAverageBck | read-only | current | The average calculated backward packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileRep… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.35 | Columnl3SatReportPdvMaxBck | read-only | current | The maximum calculated backward packet delay variation. This object is relevant only when l3SatPeerResponderType is loopAndTimestamp(4) and l3SatPeerProfileRep… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.36 | Columnl3SatReportValidRxTwampPacketsFwd | read-only | current | The number of valid received TWAMP packets in the forward direction. Timeout (lost) and duplicated packets are not valid. The PDR is calculated by: (l3SatRepor… |
| 1.3.6.1.4.1.164.6.1.15.3.11.1.37 | Columnl3SatReportValidRxTwampPacketsBck | read-only | current | The number of valid received TWAMP packets in the backward direction. Timeout (lost) and duplicated packets are not valid. The PDR is calculated by: (l3SatRepo… |
| 1.3.6.1.4.1.164.6.1.15.7 | IdentityradL3Sat | L3 SAT MIB. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| RadTestIpSizeIndex | INTEGER { ip64 (1), ip128 (2), ip256 (3), ip512 (4), ip1024 (5), ip1280 (6), ip1500 (7), ipMtu (8), ipCustom (9) } | current | This TC is used to index a table according to the range of IP size values. |
| RadTestIpSizeValues | BITS { ip64Val (0), ip128Val (1), ip256Val (2), ip512Val (3), ip1024Val (4), ip1280Val (5), ip1500Val (6), ipMtuVal (7), ipCustomVal (8) } | current | This TC is used for configuring a set of IP size values. |