SLE-MPLS-LDP-MIB
216 objects
Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.6296 | Nodedasan | |||
| 1.3.6.1.4.1.6296.101 | NodesleMgmt | |||
| 1.3.6.1.4.1.6296.101.16 | NodesleMpls | |||
| 1.3.6.1.4.1.6296.101.16.52 | IdentitysleMplsLdpMibBase | Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: … | ||
| 1.3.6.1.4.1.6296.101.16.52.1 | NodesleMplsLdpScalars | |||
| 1.3.6.1.4.1.6296.101.16.52.1.1 | NodesleMplsLdpInfoScalars | |||
| 1.3.6.1.4.1.6296.101.16.52.1.1.1 | ScalarsleMplsLdpInfoRouterStatus | read-only | current | The Object is used to create the Ldpinstance. Without this object, the LSR does not perform any LDP operations, such as sending hello packets. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.2 | ScalarsleMplsLdpInfoRouterId | read-only | current | The Label Switching Router's Identifier. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.3 | ScalarsleMplsLdpInfoCTRLMode | read-only | current | In independent control mode, each LSR might advertise label mappings to its neighbors at any time. In independentdownstream-on-demand mode, an LSR might answer… |
| 1.3.6.1.4.1.6296.101.16.52.1.1.4 | ScalarsleMplsLdpInfoHelloInterval | read-only | current | This object to set the global value for the interval after which keep-alive packets are sent out. The 16-bit integer value which is the proposed Hello Interval… |
| 1.3.6.1.4.1.6296.101.16.52.1.1.5 | ScalarsleMplsLdpInfoKeepaliveInterval | read-only | current | This object to set the global value for the interval after which keep-alive packets are sent out. Each LSR must send keep-alive messages at regular intervals t… |
| 1.3.6.1.4.1.6296.101.16.52.1.1.6 | ScalarsleMplsLdpInfoTargetpeerHelloInterval | read-only | current | This object is to set the interval for sending unicast hello packets to targeted peers. Use the no parameter with this object to revert to the default targeted… |
| 1.3.6.1.4.1.6296.101.16.52.1.1.7 | ScalarsleMplsLdpInfoKeepaliveTimeout | read-only | current | This object is used to set the global value for the interval after which keep-alive packets are sent out. The 16-bit integer value which is the proposed keep -… |
| 1.3.6.1.4.1.6296.101.16.52.1.1.8 | ScalarsleMplsLdpInfoHelloHoldTimer | read-only | current | This object is to set the global value for the hold-time after which the LSR rejects The 16-bit integer value which is the proposed Hello hold timer for this L… |
| 1.3.6.1.4.1.6296.101.16.52.1.1.9 | ScalarsleMplsLdpInfoLabelRetention | read-only | current | This Object is to set the global value for the retention mode to be used for all labels exchanged Any changes made to the retention mode for an interface (afte… |
| 1.3.6.1.4.1.6296.101.16.52.1.1.10 | ScalarsleMplsLdpInfoTargetPeerHelloHoldTime | read-only | current | This object to set the time-out value that is the time that the router waits before rejecting an adjacency with targeted peers. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.11 | ScalarsleMplsLdpInfoExplicitNull | read-only | current | This object to router to send explicit-null labels for directly connected FECs instead of implicit-nulllabels. Implicit-nulls are the default labels. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.12 | ScalarsleMplsLdpInfoMulticastHello | read-only | current | This object is used to display the multicastHello . |
| 1.3.6.1.4.1.6296.101.16.52.1.1.13 | ScalarsleMplsLdpInfoImportBgpRoute | read-only | current | This object is used to display the Import BgpRoutes. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.14 | ScalarsleMplsLdpInfoPropagateRelease | read-only | current | This object is used to display the Propagate Release. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.15 | ScalarsleMplsLdpInfoPwStatusTlv | read-only | current | This object is used to display the Pw-Status Tlv. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.16 | ScalarsleMplsLdpInfoOptimization | read-only | current | This object is used to display the ldp Optimization. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.17 | ScalarsleMplsLdpInfoRequestRetry | read-only | current | This object is used to display the Request Retry. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.18 | ScalarsleMplsLdpInfoRequestRetryTimeOut | read-only | current | This object is used to display the Request Retry Timeout. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.19 | ScalarsleMplsLdpInfoLabelDistMethod | read-only | current | This object is used to display the label distribution mode. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.20 | ScalarsleMplsLdpInfoGlobalMergeCapability | read-only | current | This object is used to display global merge capability. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.21 | ScalarsleMplsLdpInfoGracefulRestart | read-only | current | This object is used to display the GracefulRestart. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.22 | ScalarsleMplsLdpInfoGracefulRestartMaximumRecoverTimer | read-only | current | This object is used to display the MaximumRecoverTimer value. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.23 | ScalarsleMplsLdpInfoGracefulRestartNeighbourLiveNess | read-only | current | This object is used to display the MaximumRecoverTimer value. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.24 | ScalarsleMplsLdpInfoLoopDetetion | read-only | current | This object is used to display the LoopDetetction. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.25 | ScalarsleMplsLdpInfoLoopDetectionPathVectorCount | read-only | current | This is object is used to display the Loopdetection . |
| 1.3.6.1.4.1.6296.101.16.52.1.1.26 | ScalarsleMplsLdpInfoLoopDetectionHopCount | read-only | current | This object is used to display LoopDetectionHopCount value. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.27 | ScalarsleMplsLdpInfoTransportAddressType | read-only | current | This object is used to display the TransportAddressType. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.28 | ScalarsleMplsLdpInfoTransportAddess | read-only | current | This specifies whether the loopback or interface address is to be used as the transport address in the transport address TLV of the hello message. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.29 | ScalarsleMplsLdpInfoLabelSpace | read-only | current | this is object is used to display the Labelspace for which a transport address is being configured. '0' is for global configured ie per platform |
| 1.3.6.1.4.1.6296.101.16.52.1.1.30 | ScalarsleMplsLdpInfoNeighBorPasswordRequired | read-only | current | This is object is used to display the neighbor password. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.31 | ScalarsleMplsLdpInfoPeerGroupAclValue | read-only | current | This object is used to display the acl value for ldp peer group. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.32 | ScalarsleMplsLdpInfoPeerGroupPasswordType | read-only | current | This object is used to display the ldp peergroup password type. |
| 1.3.6.1.4.1.6296.101.16.52.1.1.33 | ScalarsleMplsLdpInfoPeerGroupPasswordValue | read-only | current | This object is used to display the password value. |
| 1.3.6.1.4.1.6296.101.16.52.1.2 | NodesleMplsLdpScalarsControl | |||
| 1.3.6.1.4.1.6296.101.16.52.1.2.1 | ScalarsleMplsLdpControlRequest | read-write | current | This object holds the possible read-write columns that can be modified in the VpnVrfIfConf table. For each read-write column of VpnVrfIfConf table, a Set Opera… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.2 | ScalarsleMplsLdpControlStatus | read-only | current | This object displays the status of the configuration done. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.3 | ScalarsleMplsLdpControlTimer | read-write | current | This object is based on the SLE style where a timer is configured for every control table. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.4 | ScalarsleMplsLdpControlTimeStamp | read-only | current | This object specifies the time at which the configuration is done. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.5 | ScalarsleMplsLdpControlReqResult | read-only | current | The standard result of the SET operation is stored here. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.6 | ScalarsleMplsLdpControlRouterStatus | read-write | current | The Object is used to create the Ldpinstance. Without this object, the LSR does not perform any LDP operations, such as sending hello packets. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.7 | ScalarsleMplsLdpControlRouterId | read-write | current | This object is used to set the router id . |
| 1.3.6.1.4.1.6296.101.16.52.1.2.8 | ScalarsleMplsLdpControlCTRLmode | read-write | current | In independent control mode, each LSR might advertise label mappings to its neighbors at any time. In independentdownstream-on-demand mode, an LSR might answer… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.9 | ScalarsleMplsLdpControlHelloInterval | read-write | current | This object to set the global value for the interval after which Hello packets are sent out. The 16-bit integer value which is the proposed Hello Interval for … |
| 1.3.6.1.4.1.6296.101.16.52.1.2.10 | ScalarsleMplsLdpControlKeepaliveInterval | read-write | current | This object to set the global value for the interval after which keep-alive packets are sent out. Each LSR must send keep-alive messages at regular intervals t… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.11 | ScalarsleMplsLdpControlTargetpeerHellointerval | read-write | current | This object is to set the interval for sending unicast hello packets to targeted peers. Use the no parameter with this object to revert to the default targeted… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.12 | ScalarsleMplsLdpControlKeepaliveTimeout | read-write | current | This object is used to set the global value for the interval after which keep-alive packets are sent out. The 16-bit integer value which is the proposed keep -… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.13 | ScalarsleMplsLdpControlHelloHoldTimer | read-write | current | This object is to set the global value for the hold-time after which the LSR rejects The 16-bit integer value which is the proposed Hello hold timer for this L… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.14 | ScalarsleMplsLdpControlLabelRetention | read-write | current | This Object is to set the global value for the retention mode to be used for all labels exchanged. Any changes made to the retention mode for an interface (aft… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.15 | ScalarsleMplsLdpControlTargetPeerHelloHoldTime | read-write | current | This object is to set global value for the time-out value that is the time that the router waits before rejecting an adjacency with targeted peers. if the valu… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.16 | ScalarsleMplsLdpControlExplicitNull | read-write | current | This object to router to send explicit-null labels for directly connected FECs instead of implicit-nulllabels. Implicit-nulls are the default labels. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.17 | ScalarsleMplsLdpControlMulticastHello | read-write | current | This object used to set the multicastHello . |
| 1.3.6.1.4.1.6296.101.16.52.1.2.18 | ScalarsleMplsLdpControlImportBgpRoutes | read-write | current | This object used to set the importBgpRoutes . |
| 1.3.6.1.4.1.6296.101.16.52.1.2.19 | ScalarsleMplsLdpControlPropagateRelease | read-write | current | This object used to set the Propogate Release. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.20 | ScalarsleMplsLdpControlPwStatusTlv | read-write | current | This object used to set the Pw-status tlv. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.21 | ScalarsleMplsLdpControlOptimization | read-write | current | This object used to set the ldp optimization. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.22 | ScalarsleMplsLdpControlRequestRetry | read-write | current | This object used to set the Request retry the retry of requests once a request for a label has been rejected for a valid reason. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.23 | ScalarsleMplsLdpControlRequestRetryTimeout | read-write | current | this object used to set request retry timeout . |
| 1.3.6.1.4.1.6296.101.16.52.1.2.24 | ScalarsleMplsLdpControlLabelDistMethod | read-write | current | This object is used to set the label distribution method. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.25 | ScalarsleMplsLdpControlGlobalMergeCapabilty | read-write | current | This object is used to set the global merge capability. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.26 | ScalarsleMplsLdpControlGracefulRestart | read-write | current | This object used to set the graceful restart. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.27 | ScalarsleMplsLdpControlGracefulRestartTimer | read-write | current | This object used the Graceful Restart Timer. 1- MaximumRecoveryTimer (15-600) 2- neighbour livenes (5-300) |
| 1.3.6.1.4.1.6296.101.16.52.1.2.28 | ScalarsleMplsLdpControlLoopDetection | read-write | current | This object is used to setthe LoopDetetction. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.29 | ScalarsleMplsLdpControlPathVectorCount | read-write | current | If the value of this object is 0 (zero) then Loop Detection for Path Vectors is disabled. Otherwise, if this object has a value greater than zero, then Loop De… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.30 | ScalarsleMplsLdpControlHopCount | read-write | current | If the value of this object is 0 (zero), then Loop Detection using Hop Counters is disabled. If the value of this object is greater than 0 (zero) then Loop Det… |
| 1.3.6.1.4.1.6296.101.16.52.1.2.31 | ScalarsleMplsLdpControlTransportAddressType | read-write | current | This is object is used to set the TransportAddressType . |
| 1.3.6.1.4.1.6296.101.16.52.1.2.32 | ScalarsleMplsLdpControlTransportAddress | read-write | current | The transport address is the address used for the TCP session over which LDP is running |
| 1.3.6.1.4.1.6296.101.16.52.1.2.33 | ScalarsleMplsLdpControlLabelSpace | read-write | current | this is object is used to set the Labelspace for which a transport address is being configured. '0' is for global configured ie per platform. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.34 | ScalarsleMplsLdpControlClear | read-write | current | This is object is used to clear ldp session and adjacency . |
| 1.3.6.1.4.1.6296.101.16.52.1.2.35 | ScalarsleMplsLdpControlNeigborPasswordRequired | read-write | current | This is object is used to enable neighbor password required. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.36 | ScalarsleMplsLdpControlPeerGroupAclValue | read-write | current | This object is used to set the acl value. |
| 1.3.6.1.4.1.6296.101.16.52.1.2.37 | ScalarsleMplsLdpControlPeerGroupPasswordType | read-write | current | This object is used to set the password type . |
| 1.3.6.1.4.1.6296.101.16.52.1.2.38 | ScalarsleMplsLdpControlPeerGroupPasswordValue | read-write | current | This object is used to set the password value. |
| 1.3.6.1.4.1.6296.101.16.52.2 | NodesleMplsLdpIfTable | |||
| 1.3.6.1.4.1.6296.101.16.52.2.1 | TablesleMplsLdpIfInfoTable | not-accessible | current | This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switching Router (LSR) and Label Edge Router (LER… |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1 | RowsleMplsLdpIfInfoEntry | not-accessible | current | An entry in this table represents ldp information of the interface mode. |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.1 | ColumnsleMplsLdpIfInfoIndex | not-accessible | current | This object is a interface index to uniquely identify the row of this table |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.2 | ColumnsleMplsLdpIfInfoEnable | read-only | current | this object is used to display the enable ldp in interface mode. |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.4 | ColumnsleMplsLdpIfInfoStatus | read-only | current | The operational status of this LDP Entity. The value of unknown(1) indicates that the operational status cannot be determined at this time. The value of unknow… |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.5 | ColumnsleMplsLdpIfInfoPrimaryIpAddress | read-only | current | This is object is used to display the Primary Ip Address . |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.6 | ColumnsleMplsLdpIfInfoInterfaceType | read-only | current | This object to display the InterfaceType. |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.7 | ColumnsleMplsLdpIfInfoMaxPduLength | read-only | current | The maximum PDU Length that is sent in the Common Session Parameters of an Initialization Message. According to the LDP Specification [RFC3036] a value of 255 … |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.8 | ColumnsleMplsLdpIfInfoKeepAliveHoldTimer | read-only | current | The 16-bit integer value which is the proposed keep alive hold timer for this LDP Interface. |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.9 | ColumnsleMplsLdpIfInfoHelloHoldTimer | read-only | current | This is object is used to display helloholdtimer for this Ldp Interface. |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.10 | ColumnsleMplsLdpIfInfoLabelDistMethod | read-only | current | This is object is used to display the LabelDistribution mode of the particular interface. |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.11 | ColumnsleMplsLdpIfInfoLabelRetentionMode | read-only | current | The LDP Entity can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized lab… |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.12 | ColumnsleMplsLdpIfInfoHelloInterval | read-only | current | This object to dispaly the interface for the interval after which Hello packets are sent out. The 16-bit integer value which is the proposed Hello Interval for… |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.14 | ColumnsleMplsLdpIfInfoKeepaliveInterval | read-only | current | This object is used to display the keepalive interval. |
| 1.3.6.1.4.1.6296.101.16.52.2.1.1.15 | ColumnsleMplsLdpIfInfoMulticastHello | read-only | current | This is obeject is used to dispaly the multicast Hello. |
| 1.3.6.1.4.1.6296.101.16.52.2.2 | NodesleMplsLdpIfControl | |||
| 1.3.6.1.4.1.6296.101.16.52.2.2.1 | ScalarsleMplsLdpIfControlRequest | read-write | current | This object holds the possible read-write columns that can be modified in the VpnVrfIfConf table. For each read-write column of VpnVrfIfConf table, a Set Opera… |
| 1.3.6.1.4.1.6296.101.16.52.2.2.2 | ScalarsleMplsLdpIfControlStatus | read-only | current | This object displays the status of the configuration done. |
| 1.3.6.1.4.1.6296.101.16.52.2.2.3 | ScalarsleMplsLdpIfControlTimer | read-write | current | This object is based on the SLE style where a timer is configured for every control table. |
| 1.3.6.1.4.1.6296.101.16.52.2.2.4 | ScalarsleMplsLdpIfControlTimestamp | read-only | current | This object specifies the time at which the configuration is done. |
| 1.3.6.1.4.1.6296.101.16.52.2.2.5 | ScalarsleMplsLdpIfControlReqResult | read-only | current | The standard result of the SET operation is stored here. |
| 1.3.6.1.4.1.6296.101.16.52.2.2.7 | ScalarsleMplsLdpIfControlIndex | read-write | current | This object is a interface index to uniquely identify the row of this table |
| 1.3.6.1.4.1.6296.101.16.52.2.2.8 | ScalarsleMplsLdpIfControlEnable | read-write | current | This is object is used to , on a specified interface. enables the transmission of Hello packets through the current interface, so that LDP adjacencies and LDP … |
| 1.3.6.1.4.1.6296.101.16.52.2.2.9 | ScalarsleMplsLdpIfControlMaxPduLength | read-write | current | The maximum PDU Length that is sent in the Common Session Parameters of an Initialization Message. According to the LDP Specification [RFC3036] a value of 255 … |
| 1.3.6.1.4.1.6296.101.16.52.2.2.10 | ScalarsleMplsLdpIfControlKeepAliveHoldTimer | read-write | current | The 16-bit integer value which is the proposed keep alive hold timer for this LDP Entity. |
| 1.3.6.1.4.1.6296.101.16.52.2.2.11 | ScalarsleMplsLdpIfControlHelloHoldTimer | read-write | current | The 16-bit integer value which is the proposed Hello hold timer for this LDP Entity. The Hello Hold time in seconds. An LSR maintains a record of Hellos receiv… |
| 1.3.6.1.4.1.6296.101.16.52.2.2.12 | ScalarsleMplsLdpIfControlLabelDistMethod | read-write | current | For any given LDP session, the method of label distribution must be specified. |
| 1.3.6.1.4.1.6296.101.16.52.2.2.13 | ScalarsleMplsLdpIfControlLabelRetentionMode | read-write | current | The LDP Entity can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized lab… |
| 1.3.6.1.4.1.6296.101.16.52.2.2.14 | ScalarsleMplsLdpIfControlHelloInterval | read-write | current | This object to set the hello interval for interface The 16-bit integer value which is the proposed Hello Interval for this LDP Entity. if the value of the obje… |
| 1.3.6.1.4.1.6296.101.16.52.2.2.15 | ScalarsleMplsLdpIfControlKeepaliveInterval | read-write | current | This object to set the interval for interface Each LSR must send keep-alive messages at regular intervals to its LDP peers to keep the sessions active. The kee… |
| 1.3.6.1.4.1.6296.101.16.52.2.2.16 | ScalarsleMplsLdpIfControlMulticastHello | read-write | current | This object is used to set the multicasthello. |
| 1.3.6.1.4.1.6296.101.16.52.3 | NodesleMplsLdpTargetedPeerTable | |||
| 1.3.6.1.4.1.6296.101.16.52.3.1 | TablesleMplsLdpTargetedPeerInfoTable | not-accessible | current | This is Table is a read-only table, the purpose of this table is targetedpeer for TargetedLdp session. |
| 1.3.6.1.4.1.6296.101.16.52.3.1.1 | RowsleMplsLdpTargetedPeerInfoEntry | not-accessible | current | this table is used to displayTargetedPeer Address . |
| 1.3.6.1.4.1.6296.101.16.52.3.1.1.1 | ColumnsleMplsLdpTargetedPeerInfoAddressType | read-only | current | This is object is used to display address type uniquely identify the entry of the table. |
| 1.3.6.1.4.1.6296.101.16.52.3.1.1.2 | ColumnsleMplsLdpTargetedPeerInfoAddress | read-only | current | this object is used to TargetedPeer Address uniquely identify the entry of the table. |
| 1.3.6.1.4.1.6296.101.16.52.3.1.1.3 | ColumnsleMplsLdpTargetedPeerInfoHelloInterval | read-only | current | This is object is used to display TargetedPeer Hello interval for Particular TargetedPeer. |
| 1.3.6.1.4.1.6296.101.16.52.3.1.1.4 | ColumnsleMplsLdpTargetedPeerInfoHoldTimer | read-only | current | This is object is used to display TargetedPeer Hello interval for Particular TargetedPeer. |
| 1.3.6.1.4.1.6296.101.16.52.3.2 | NodesleMplsLdpTargetedPeerControl | |||
| 1.3.6.1.4.1.6296.101.16.52.3.2.1 | ScalarsleMplsLdpTargetedPeerControlRequest | read-write | current | This object holds the possible read-write columns that can be modified in the VpnVrfIfConf table. For each read-write column of VpnVrfIfConf table, a Set Opera… |
| 1.3.6.1.4.1.6296.101.16.52.3.2.2 | ScalarsleMplsLdpTargetedPeerControlStatus | read-only | current | This object displays the status of the configuration done. |
| 1.3.6.1.4.1.6296.101.16.52.3.2.3 | ScalarsleMplsLdpTargetedPeerControlTimer | read-write | current | This object is based on the SLE style where a timer is configured for every control table. |
| 1.3.6.1.4.1.6296.101.16.52.3.2.4 | ScalarsleMplsLdpTargetedPeerControlTimestamp | read-only | current | This object specifies the time at which the configuration is done. |
| 1.3.6.1.4.1.6296.101.16.52.3.2.5 | ScalarsleMplsLdpTargetedPeerControlReqResult | read-only | current | The standard result of the SET operation is stored here. |
| 1.3.6.1.4.1.6296.101.16.52.3.2.6 | ScalarsleMplsLdpTargetedPeerAddressType | read-write | current | This is object is used to set the Targeted PeerAddress Type. |
| 1.3.6.1.4.1.6296.101.16.52.3.2.7 | ScalarsleMplsLdpTargetedPeerAddress | read-only | current | This is object is used to set the TargetedPeerAddress. |
| 1.3.6.1.4.1.6296.101.16.52.3.2.8 | ScalarsleMplsLdpTargetedPeerHelloInterval | read-write | current | this is object is used to set Targeted hello interval . |
| 1.3.6.1.4.1.6296.101.16.52.3.2.9 | ScalarsleMplsLdpTargetedPeerHoldTime | read-write | current | this is object is used to set Targeted hello interval. |
| 1.3.6.1.4.1.6296.101.16.52.4 | NodesleMplsLdpSessionTable | |||
| 1.3.6.1.4.1.6296.101.16.52.4.1 | TablesleMplsLdpSessionInfoTable | not-accessible | current | A table of Sessions between the LDP Entities and LDP Peers. This table AUGMENTS the slemplsLdpPeerTable. Each row in this table represents a single session. |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1 | RowsleMplsLdpSessionInfoEntry | not-accessible | current | An entry in this table represents information on a single session between an LDP Entity and LDP Peer. The information contained in a row is read-only. Please n… |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1.1 | ColumnsleMplsLdpSessionInfoRouterId | read-only | current | this object is used to uniquely identify the row. |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1.2 | ColumnsleMplsLdpSessionInfoPeerRouterId | read-only | current | this object is used to uniquely identify the row. |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1.4 | ColumnsleMplsLdpSessionInfoRole | read-only | current | During session establishment the LSR/LER takes either the active role or the passive role based on address comparisons. This object indicates whether this LSR/… |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1.5 | ColumnsleMplsLdpSessionInfoState | read-only | current | The current state of the session, all of the states 1 to 5 are based on the state machine for session negotiation behavior. |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1.6 | ColumnsleMplsLdpSessionInfoKeepAliveTime | read-only | current | The negotiated KeepAlive Time which represents the amount of seconds between keep alive messages. This value is negotiated during session initialization betwee… |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1.7 | ColumnsleMplsLdpSessionInfoIfIndex | read-only | current | This is object is used to display the interface index of session. |
| 1.3.6.1.4.1.6296.101.16.52.4.1.1.8 | ColumnsleMplsLdpSessionInfoType | read-only | current | This is object is used to say session is Noraml or Targetted. |
| 1.3.6.1.4.1.6296.101.16.52.5 | NodesleMplsLdpHelloAdjacencyTable | |||
| 1.3.6.1.4.1.6296.101.16.52.5.1 | TablesleMplsLdpHelloAdjacencyInfoTable | not-accessible | current | A table of Hello Adjacencies for Sessions. |
| 1.3.6.1.4.1.6296.101.16.52.5.1.1 | RowsleMplsLdpHelloAdjacencyInfoEntry | not-accessible | current | Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello Adjacencies. |
| 1.3.6.1.4.1.6296.101.16.52.5.1.1.1 | ColumnsleMplsLdpHelloAdjacencyInfoPeerIpAddress | read-only | current | This object is used to display the Interface Ipaddress of the Peer. |
| 1.3.6.1.4.1.6296.101.16.52.5.1.1.2 | ColumnsleMplsLdpHelloAdjacencyInfoHoldTime | read-only | current | This object is used to display helloadjacency holdtime. |
| 1.3.6.1.4.1.6296.101.16.52.5.1.1.3 | ColumnsleMplsLdpHelloAdjacencyInfoPeerLdpIdentifier | read-only | current | This object is used to display the LdpId of The Peer. LdpId is the combination fo LsrId and LabelSpace. |
| 1.3.6.1.4.1.6296.101.16.52.5.1.1.4 | ColumnsleMplsLdpHelloAdjacencyInfoType | read-only | current | This adjacency is the result of a 'NormalPeer' hello if the value of this object is NoramalPeer(1). Otherwise, it is a result of a 'targeted' hello, targeted(2… |
| 1.3.6.1.4.1.6296.101.16.52.5.1.1.5 | ColumnsleMplsLdpHelloAdjacencyInfoIfIndex | read-only | current | This is object is used to display the interface index of adjacency. |
| 1.3.6.1.4.1.6296.101.16.52.6 | NodesleMplsLdpUpStreamTable | |||
| 1.3.6.1.4.1.6296.101.16.52.6.1 | TablesleMplsLdpUpStreamInfoTable | not-accessible | current | A table which shows the relationship between LDP LSPs FEC for upstream information. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1 | RowsleMplsLdpUpStreamInfoEntry | not-accessible | current | An entry represents a label for the particular fec. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.1 | ColumnsleMplsLdpUpStreamInfoNetworkAddress | read-only | current | This object is uniquely identify the row. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.2 | ColumnsleMplsLdpUpStreamInfoPeerAddress | read-only | current | This object is uniquely identify the row. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.3 | ColumnsleMplsLdpUpStreamInfoNetworkAddressType | read-only | current | This object is to display network address type. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.4 | ColumnsleMplsLdpUpStreamInfoNeworkAddressLength | read-only | current | This object is used to display network address length. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.5 | ColumnsleMplsLdpUpStreamInfoState | read-only | current | This is object to display the state |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.6 | ColumnsleMplsLdpUpStreamInfoLabel | read-only | current | This object used to display the label of the particular fec 1048576 is a invalid label. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.7 | ColumnsleMplsLdpUpStreamInfoAttr | read-only | current | This object used to display the Attr. |
| 1.3.6.1.4.1.6296.101.16.52.6.1.1.8 | ColumnsleMplsLdpUpStreamInfoMapLabel | read-only | current | Map label of a FEC. 1048576 is a invalid label. |
| 1.3.6.1.4.1.6296.101.16.52.7 | NodesleMplsLdpDownStreamTable | |||
| 1.3.6.1.4.1.6296.101.16.52.7.1 | TablesleMplsLdpDownStreamInfoTable | not-accessible | current | A table which shows the relationship between LDP LSPs FEC for DownStream information. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1 | RowsleMplsLdpDownStreamInfoEntry | not-accessible | current | An entry represents a label for the particular fec. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.1 | ColumnsleMplsLdpDownStreamInfoNetworkAddress | read-only | current | This object is uniquely identify the row. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.2 | ColumnsleMplsLdpDownStreamInfoPeerAddress | read-only | current | This object is uniquely identify the row. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.3 | ColumnsleMplsLdpDownStreamInfoNetworkAddressType | read-only | current | This object is to display network address type. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.4 | ColumnsleMplsLdpDownStreamInfoNeworkAddressLength | read-only | current | This object is used to display network address length. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.5 | ColumnsleMplsLdpDownStreamInfoState | read-only | current | This is object to display the state |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.6 | ColumnsleMplsLdpDownStreamInfoLabel | read-only | current | This object used to display the label of the particular fec 1048576 is a invalid label. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.7 | ColumnsleMplsLdpDownStreamInfoNextHopAddress | read-only | current | This object used to display nexthopaddress for the particular fec. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.8 | ColumnsleMplsLdpDownStreamInfoAttr | read-only | current | This object used to display the Attr. |
| 1.3.6.1.4.1.6296.101.16.52.7.1.1.9 | ColumnsleMplsLdpDownStreamInfoMapLabel | read-only | current | Map label of a FEC. 1048576 is invalid label. |
| 1.3.6.1.4.1.6296.101.16.52.8 | NodesleMplsLdpAdvertiseLabelTable | |||
| 1.3.6.1.4.1.6296.101.16.52.8.1 | TablesleMplsLdpAdvertiseLabelInfoTable | not-accessible | current | This table is used to display the Advertise Label. |
| 1.3.6.1.4.1.6296.101.16.52.8.1.1 | RowsleMplsLdpAdvertiseLabelInfoEntry | not-accessible | current | An Entry is represent for the Advertise Label. |
| 1.3.6.1.4.1.6296.101.16.52.8.1.1.1 | ColumnsleMplsLdpAdvertiseLabelInfoIndex | not-accessible | current | This object used to uniquely identify the table. |
| 1.3.6.1.4.1.6296.101.16.52.8.1.1.2 | ColumnsleMplsLdpAdvertiseLabelInfoType | read-only | current | This object is used to display the label type. |
| 1.3.6.1.4.1.6296.101.16.52.8.1.1.3 | ColumnsleMplsLdpAdvetiseLabelInfoPrefixAcl | read-only | current | This object is used to display prefix Acl. |
| 1.3.6.1.4.1.6296.101.16.52.8.1.1.4 | ColumnsleMplsLdpAdvertiseLabelInfoPeerAcl | read-only | current | This object is used to display peer Acl . |
| 1.3.6.1.4.1.6296.101.16.52.8.2 | NodesleMplsLdpAdvertiseLabelControl | |||
| 1.3.6.1.4.1.6296.101.16.52.8.2.1 | ScalarsleMplsLdpAdvertiseLabelControlRequest | read-write | current | This object holds the possible read-write columns that can be modified in the VpnVrfIfConf table. For each read-write column of VpnVrfIfConf table, a Set Opera… |
| 1.3.6.1.4.1.6296.101.16.52.8.2.2 | ScalarsleMplsLdpAdvertiseLabelControlStatus | read-only | current | This object displays the status of the configuration done. |
| 1.3.6.1.4.1.6296.101.16.52.8.2.3 | ScalarsleMplsLdpAdvertiseLabelControlTimer | read-write | current | This object is based on the SLE style where a timer is configured for every control table. |
| 1.3.6.1.4.1.6296.101.16.52.8.2.4 | ScalarsleMplsLdpAdvertiseLabelControlTimestamp | read-only | current | This object specifies the time at which the configuration is done. |
| 1.3.6.1.4.1.6296.101.16.52.8.2.5 | ScalarsleMplsLdpAdvertiseLabelControlReqResult | read-only | current | The standard result of the SET operation is stored here. |
| 1.3.6.1.4.1.6296.101.16.52.8.2.6 | ScalarsleMplsLdpAdvertiseLabelControlType | read-write | current | This object is used to set the Type of Advertise label type . |
| 1.3.6.1.4.1.6296.101.16.52.8.2.7 | ScalarsleMplsLdpAdvertiseLabelControlPrefixAcl | read-write | current | This object is used to set the prefix acl . |
| 1.3.6.1.4.1.6296.101.16.52.8.2.8 | ScalarsleMplsLdpAdvertiseLabelControlPeerAcl | read-write | current | This object is used to set the peer Acl . |
| 1.3.6.1.4.1.6296.101.16.52.9 | NodesleMplsLdpImportingLabelTable | |||
| 1.3.6.1.4.1.6296.101.16.52.9.1 | TablesleMplsLdpImportingLabelInfoTable | not-accessible | current | This table is used to display the Importing Label. |
| 1.3.6.1.4.1.6296.101.16.52.9.1.1 | RowsleMplsLdpImportingLabelInfoEntry | not-accessible | current | An Entry is represent for the Importing Label. |
| 1.3.6.1.4.1.6296.101.16.52.9.1.1.1 | ColumnsleMplsLdpImportingLabelInfoIndex | not-accessible | current | This object used to uniquely identify the table. |
| 1.3.6.1.4.1.6296.101.16.52.9.1.1.2 | ColumnsleMplsLdpImportingLabelInfoType | read-only | current | This object is used to display the label type. |
| 1.3.6.1.4.1.6296.101.16.52.9.1.1.3 | ColumnsleMplsLdpImportingLabelInfoPeerAcl | read-only | current | This object is used to display prefix Acl. |
| 1.3.6.1.4.1.6296.101.16.52.9.1.1.4 | ColumnsleMplsLdpImportingLabelInfoPrefixAcl | read-only | current | This object is used to display peer Acl . |
| 1.3.6.1.4.1.6296.101.16.52.9.2 | NodesleMplsLdpImportingLabelControl | |||
| 1.3.6.1.4.1.6296.101.16.52.9.2.1 | ScalarsleMplsLdpImportingLabelControlRequest | read-write | current | This object holds the possible read-write columns that can be modified in the VpnVrfIfConf table. For each read-write column of VpnVrfIfConf table, a Set Opera… |
| 1.3.6.1.4.1.6296.101.16.52.9.2.2 | ScalarsleMplsLdpImportingLabelControlStatus | read-only | current | This object displays the status of the configuration done. |
| 1.3.6.1.4.1.6296.101.16.52.9.2.3 | ScalarsleMplsLdpImportingLabelControlTimer | read-write | current | This object is based on the SLE style where a timer is configured for every control table. |
| 1.3.6.1.4.1.6296.101.16.52.9.2.4 | ScalarsleMplsLdpImportingLabelControlTimestamp | read-only | current | This object specifies the time at which the configuration is done. |
| 1.3.6.1.4.1.6296.101.16.52.9.2.5 | ScalarsleMplsLdpImportingLabelControlReqResult | read-only | current | The standard result of the SET operation is stored here. |
| 1.3.6.1.4.1.6296.101.16.52.9.2.6 | ScalarsleMplsLdpImportingLabelControlType | read-write | current | This object is used to set the Type of Importing label type . |
| 1.3.6.1.4.1.6296.101.16.52.9.2.7 | ScalarsleMplsLdpImportingLabelControlPeerAcl | read-write | current | This object is used to set the prefix acl . |
| 1.3.6.1.4.1.6296.101.16.52.9.2.8 | ScalarsleMplsLdpImportingLabelControlPrefixAcl | read-write | current | This object is used to set the peer Acl . |
| 1.3.6.1.4.1.6296.101.16.52.10 | NodesleMplsLdpPeerPasswordTable | |||
| 1.3.6.1.4.1.6296.101.16.52.10.1 | TablesleMplsLdpPeerPasswordInfoTable | not-accessible | current | This table is used to display the Importing Label. |
| 1.3.6.1.4.1.6296.101.16.52.10.1.1 | RowsleMplsLdpPeerPasswordInfoEntry | not-accessible | current | An Entry is represent for the peer password . |
| 1.3.6.1.4.1.6296.101.16.52.10.1.1.1 | ColumnsleMplsLdpPeerPasswordInfoAddress | not-accessible | current | This object used to uniquely identify the table. |
| 1.3.6.1.4.1.6296.101.16.52.10.1.1.2 | ColumnsleMplsLdpPeerPasswordAuthType | read-only | current | This object is used to display the authentication type. |
| 1.3.6.1.4.1.6296.101.16.52.10.1.1.3 | ColumnsleMplsLdpPeerPasswordInfoType | read-only | current | This object is used to display password type. |
| 1.3.6.1.4.1.6296.101.16.52.10.1.1.4 | ColumnsleMplsLdpPeerPasswordValue | read-only | current | This object is used to display passwordValue . |
| 1.3.6.1.4.1.6296.101.16.52.10.2 | NodesleMplsLdpPeerPasswordControl | |||
| 1.3.6.1.4.1.6296.101.16.52.10.2.1 | ScalarsleMplsLdpPeerPasswordControlRequest | read-write | current | This object holds the possible read-write columns that can be modified in the VpnVrfIfConf table. For each read-write column of VpnVrfIfConf table, a Set Opera… |
| 1.3.6.1.4.1.6296.101.16.52.10.2.2 | ScalarsleMplsLdpPeerPasswordControlStatus | read-only | current | This object displays the status of the configuration done. |
| 1.3.6.1.4.1.6296.101.16.52.10.2.3 | ScalarsleMplsLdpPeerPasswordControlTimer | read-write | current | This object is based on the SLE style where a timer is configured for every control table. |
| 1.3.6.1.4.1.6296.101.16.52.10.2.4 | ScalarsleMplsLdpPeerPasswordControlTimestamp | read-only | current | This object specifies the time at which the configuration is done. |
| 1.3.6.1.4.1.6296.101.16.52.10.2.5 | ScalarsleMplsLdpPeerPasswordControlReqResult | read-only | current | The standard result of the SET operation is stored here. |
| 1.3.6.1.4.1.6296.101.16.52.10.2.6 | ScalarsleMplsLdpPeerPasswordControlAddress | read-write | current | This object is used to set peer address. |
| 1.3.6.1.4.1.6296.101.16.52.10.2.7 | ScalarsleMplsLdpPeerPasswordControlType | read-write | current | This object is used to set password type . |
| 1.3.6.1.4.1.6296.101.16.52.10.2.8 | ScalarsleMplsLdpPeerPasswordControlValue | read-write | current | This object is used to set the Password value . |