below
243 objects
This MIB defines the objects for the Ethernet Flow MIB.
Imported Objects
| ADTRAN-GENPORT-MIB | adGenPortInfoIndex |
| ADTRAN-GENSLOT-MIB | adGenSlotInfoIndex |
| ADTRAN-GENTRAPINFORM-MIB | adTrapInformSeqNum |
| ADTRAN-SHARED-CND-SYSTEM-MIB MISSING | adGenEthernetDslamFlow adGenEthernetDslamFlowID |
| ADTRAN-SHARED-CND-SYSTEM-TC-MIB MISSING | GenSystemInterfaceType |
| ADTRAN-TAeSCUEXT1-MIB | adTAeSCUTrapAlarmLevel |
| ADTRAN-TAMINIDSLAM3G-MIB | adGenMiniDslam3gMacAddress |
| IF-MIB | ifIndex |
| SNMPv2-CONF | NOTIFICATION-GROUP |
| SNMPv2-MIB | sysName |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString PhysAddress RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.664.5.70.2.1 | TableadGenEthernetInterfaceTable | not-accessible | current | This table specifies the parameters specific to a Interface. A Interface can be a physical ethernet port, an EFM Bonding group, an ATM VCL, a PON Gem port, or … |
| 1.3.6.1.4.1.664.5.70.2.1.1 | RowadGenEthernetInterfaceEntry | not-accessible | current | An entry in the adGenEthernetInterfaceTable. |
| 1.3.6.1.4.1.664.5.70.2.1.1.1 | ColumnadGenEthernetInterfaceLogicalIndex | not-accessible | current | An implementation specific index defining a Logical Interface on a particular physical ifIndex. It is the same number as the subinterface in the CLI. For examp… |
| 1.3.6.1.4.1.664.5.70.2.1.1.2 | ColumnadGenEthernetInterfaceMaxMACAddresses | read-create | current | Specify the maximum number of MAC addresses for this Interface. |
| 1.3.6.1.4.1.664.5.70.2.1.1.3 | ColumnadGenEthernetInterfaceFlowList | read-only | current | A string of indices of flows applied to this Interface. |
| 1.3.6.1.4.1.664.5.70.2.1.1.4 | ColumnadGenEthernetInterfaceSourceAuthentication | read-create | current | If this is enabled then only authenticated flows will pass traffic for this Ethernet Interface. |
| 1.3.6.1.4.1.664.5.70.2.1.1.5 | ColumnadGenEthernetInterfaceType | read-only | current | Describes the interface type of ethernet interface |
| 1.3.6.1.4.1.664.5.70.2.1.1.6 | ColumnadGenEthernetInterfaceTypeSpecific | read-only | current | This item returns a vector of interface type specific data byte# | Descr ATM - 0 | Upper 4 bits = 0, Lower 4 bits = Upper 4 bits of VPI 1 | Lower 8 bits of VPI… |
| 1.3.6.1.4.1.664.5.70.2.2 | TableadGenEthernetDslamFlowTable | not-accessible | current | This table consists of the mapping from a user ethernet interface into an S-Tag or S-Tag/C-Tag. |
| 1.3.6.1.4.1.664.5.70.2.2.1 | RowadGenEthernetDslamFlowEntry | not-accessible | current | An entry in the adGenEthernetDslamFlowTable. Each entry is an entry in a list of maps that can be applied to a user port. |
| 1.3.6.1.4.1.664.5.70.2.2.1.1 | ColumnadGenEthernetDslamFlowIndex | not-accessible | current | Index that specifies an individual map. |
| 1.3.6.1.4.1.664.5.70.2.2.1.2 | ColumnadGenEthernetDslamFlowName | read-create | current | This object is provided so that the user can identify the ethernet flow uniquely. The profile will be stored in the EMS by name and applied to the user-specifi… |
| 1.3.6.1.4.1.664.5.70.2.2.1.3 | ColumnadGenEthernetDslamFlowTrafficDirection | read-create | current | Specify the traffic direction to which this map applies. Upstream: Customer C-Tag, Pbit, Ethertype, DSCP, and IP Protocol are used to classify traffic upstream… |
| 1.3.6.1.4.1.664.5.70.2.2.1.4 | ColumnadGenEthernetDslamFlowNetworkSTag | read-create | current | Specify the STag seen on network traffic. |
| 1.3.6.1.4.1.664.5.70.2.2.1.5 | ColumnadGenEthernetDslamFlowNetworkCTag | read-create | current | Specify the CTag seen on network ingress/egress traffic. A value of 4095 indicates that no Network CTag is used. A value of 4096 indicates that that the Networ… |
| 1.3.6.1.4.1.664.5.70.2.2.1.6 | ColumnadGenEthernetDslamFlowCEVlan | read-create | current | Specify the CEVlan seen on customer ingress/egress traffic. A value of 4095 indicates that no CEVlan is present. A value of 4097 indicates that customer traffi… |
| 1.3.6.1.4.1.664.5.70.2.2.1.7 | ColumnadGenEthernetDslamFlowDownstreamForwardingMode | read-create | current | Specify how ethernet frames on this flow are forwarded through the switch. This value is bitmasked so that forwarding modes can be combined. src (0x1) - Use th… |
| 1.3.6.1.4.1.664.5.70.2.2.1.8 | ColumnadGenEthernetDslamFlowDownstreamPbitMethod | read-create | current | Specify the PBit mapping mode in from the network to customer. Inherit - downstream traffic should egress the Interface with the priority from the network. Mar… |
| 1.3.6.1.4.1.664.5.70.2.2.1.9 | ColumnadGenEthernetDslamFlowDownstreamPbitMarking | read-create | current | If the network Pbit mode is marked then this variable specifies the downstream pBit. |
| 1.3.6.1.4.1.664.5.70.2.2.1.10 | ColumnadGenEthernetDslamFlowDownstreamPbitMapping | read-create | current | If the network Pbit mode is mapped then this variable specifies the ingress/egress priority mapping index. |
| 1.3.6.1.4.1.664.5.70.2.2.1.11 | ColumnadGenEthernetDslamFlowNetworkIngressPbit | read-create | current | This option is a bitmask used to specify a list of allowable P-bit values of the S-Tag ingressing from the network. A value of 255 indicates that this value is… |
| 1.3.6.1.4.1.664.5.70.2.2.1.12 | ColumnadGenEthernetDslamFlowNetworkIngressEtherType | read-create | current | Specify the EtherType value that will be used to classify NetworkIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.2.1.13 | ColumnadGenEthernetDslamFlowNetworkIngressDSCP | read-create | current | Specify a single DSCP value that will be used to classify NetworkIngress traffic. A value of 64 indicates this filter is disabled. If multiple DSCP values shou… |
| 1.3.6.1.4.1.664.5.70.2.2.1.14 | ColumnadGenEthernetDslamFlowNetworkIngressIPProtocolID | read-create | current | Specify the IP Protocol ID that will be used to classify NetworkIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.2.1.15 | ColumnadGenEthernetDslamFlowUpstreamForwardingMode | read-create | current | Specify how ethernet frames on this flow are forwarded through the switch. This value is bitmasked so that forwarding modes can be combined. src (0x1) - Use th… |
| 1.3.6.1.4.1.664.5.70.2.2.1.16 | ColumnadGenEthernetDslamFlowUpstreamSTagPbitMethod | read-create | current | Specify the PBit mapping mode in from the Customer to Network STag. Inherit - upstream STags should egress with the priority from the customer. Marked - upstre… |
| 1.3.6.1.4.1.664.5.70.2.2.1.17 | ColumnadGenEthernetDslamFlowUpstreamSTagPbitMarking | read-create | current | If the Customer Pbit mode is marked then this variable specifies the upstream STag pBit. |
| 1.3.6.1.4.1.664.5.70.2.2.1.18 | ColumnadGenEthernetDslamFlowUpstreamSTagPbitMapping | read-create | current | If the Customer Pbit mode is mapped then this variable specifies the ingress/egress STag priority mapping index. |
| 1.3.6.1.4.1.664.5.70.2.2.1.19 | ColumnadGenEthernetDslamFlowUpstreamCTagPbitMethod | read-create | current | Specify the CTag PBit mapping mode in from the Customer to Network. Inherit - upstream traffic should egress with the priority from the customer. Marked - upst… |
| 1.3.6.1.4.1.664.5.70.2.2.1.20 | ColumnadGenEthernetDslamFlowUpstreamCTagPbitMarking | read-create | current | If the Customer Pbit mode is marked then this variable specifies the upstream CTag pBit. |
| 1.3.6.1.4.1.664.5.70.2.2.1.21 | ColumnadGenEthernetDslamFlowUpstreamCTagPbitMapping | read-create | current | If the Customer Pbit mode is mapped then this variable specifies the ingress/egress CTag priority mapping index. |
| 1.3.6.1.4.1.664.5.70.2.2.1.22 | ColumnadGenEthernetDslamFlowCustomerIngressPbit | read-create | current | This option is a bitmask used to specify a list of allowable P-bit values of the CEVlan ingressing from the customer. A value of 255 indicates that this value … |
| 1.3.6.1.4.1.664.5.70.2.2.1.23 | ColumnadGenEthernetDslamFlowCustomerIngressEtherType | read-create | current | Specify the EtherType value that will be used to classify CustomerIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.2.1.24 | ColumnadGenEthernetDslamFlowCustomerIngressDSCP | read-create | current | Specify a single DSCP value that will be used to classify CustomerIngress traffic. A value of 64 indicates this filter is disabled. If multiple DSCP values sho… |
| 1.3.6.1.4.1.664.5.70.2.2.1.25 | ColumnadGenEthernetDslamFlowCustomerIngressIPProtocolID | read-create | current | Specify the IP Protocol ID that will be used to classify CustomerIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.2.1.26 | ColumnadGenEthernetDslamFlowCustomerIngressBroadcast | read-create | current | This variable specifies whether or not to drop CustomerIngress broadcasts on this map. |
| 1.3.6.1.4.1.664.5.70.2.2.1.27 | ColumnadGenEthernetDslamFlowCustomerIngressMulticast | read-create | current | This variable specifies whether or not to drop CustomerIngress multicasts on this map. |
| 1.3.6.1.4.1.664.5.70.2.2.1.28 | ColumnadGenEthernetDslamFlowCustomerIngressUnicast | read-create | current | This variable specifies whether or not to drop CustomerIngress unicasts on this map. |
| 1.3.6.1.4.1.664.5.70.2.2.1.29 | ColumnadGenEthernetDslamFlowCustomerIngressPolicer | read-create | current | Indicate which policer to on customer ingress traffic. A value of 0 means no policer is used on customer ingress traffic. A non-zero value represents a row fro… |
| 1.3.6.1.4.1.664.5.70.2.2.1.30 | ColumnadGenEthernetDslamFlowEncapsMode | read-create | current | Encapsulation mode/type if applicable; 'notApplicable' otherwise. IPoE and PPPoE specify a particular protocol over ethernet. 'Ethernet' specifies that any pro… |
| 1.3.6.1.4.1.664.5.70.2.2.1.31 | ColumnadGenEthernetDslamFlowManualAddrAging | read-create | current | Manual Address Aging in minutes for unicast MACs. |
| 1.3.6.1.4.1.664.5.70.2.2.1.32 | ColumnadGenEthernetDslamFlowIntermedAgent | read-create | current | Enable/disable Intermediate Agent if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.2.1.33 | ColumnadGenEthernetDslamFlowDhcpRelay | read-create | current | Set the DHCPv4 processing mode: Enabled(1)- Use DHCPv4 for subscriber authentication Disabled(2)- Discard DHCPv4 Not Applicable(3)- Unused Transparent(4)- Igno… |
| 1.3.6.1.4.1.664.5.70.2.2.1.34 | ColumnadGenEthernetDslamFlowOption82Insert | read-create | current | Enable/disable Option 82 Insertion if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.2.1.35 | ColumnadGenEthernetDslamFlowLearnedIpAddrAgingMethod | read-create | current | Method for Learned IP Address Aging if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.2.1.36 | ColumnadGenEthernetDslamFlowIgmpProcessing | read-create | current | Method for IGMP Processing if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.2.1.37 | ColumnadGenEthernetDslamFlowIgmpVersion | read-create | current | IGMP Version if applicable: v3 implies v1, v2, and v3; v2 implies v1 and v2; v1 is v1 only; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.2.1.38 | ColumnadGenEthernetDslamFlowLastMemberQueryInterval | read-create | current | Last Member Query Interval in milliseconds. This is the amount of time between Queries. Low value results in faster detection of missed leaves. |
| 1.3.6.1.4.1.664.5.70.2.2.1.39 | ColumnadGenEthernetDslamFlowLastMemberQueryCount | read-create | current | Last Member Query Count. This is the number of queries before declaring no membership of a group (channel). |
| 1.3.6.1.4.1.664.5.70.2.2.1.40 | ColumnadGenEthernetDslamFlowImmediateLeave | read-create | current | Enable/disable Immediate Leave if applicable; 'notApplicable' otherwise. Disable is the equivalent of setting Last Member Query Count to 0. |
| 1.3.6.1.4.1.664.5.70.2.2.1.41 | ColumnadGenEthernetDslamFlowMaxAllowedMcastGroups | read-create | current | Maximum Allowed Non-Guaranteed Multicast Groups. This value is only considered if multicast groups are enabled. |
| 1.3.6.1.4.1.664.5.70.2.2.1.42 | ColumnadGenEthernetDslamFlowDhcpPPPoERemoteId | read-create | current | Enable/disable Remote ID insertion into DHCPv4 Option 82 or DHCPv6 relay agent in option 37 or PPPoE Vendor Specific tag if applicable. |
| 1.3.6.1.4.1.664.5.70.2.2.1.43 | ColumnadGenEthernetDslamFlowDhcpPPPoELoopCharacteristics | read-create | current | Enable/disable loop characteristics insertion into DHCPv4 Option 82 or DHCPv6 relay agent option 17 (vendor specific) loop characteristics or PPPoE Vendor Spec… |
| 1.3.6.1.4.1.664.5.70.2.2.1.44 | ColumnadGenEthernetDslamFlowDhcpPPPoECircuitIdFormat | read-create | current | Used to provision the format of the circuit ID string. This string is returned by the PPPoE intermediate agent and DHCP relay agent in v4 sub option 1 or in v6… |
| 1.3.6.1.4.1.664.5.70.2.2.1.45 | ColumnadGenEthernetDslamFlowPPPoASessionTimeout | read-create | current | Used to set the PPPoA Session timeout when the mapping is provisioned for PPPoA encapsulation. |
| 1.3.6.1.4.1.664.5.70.2.2.1.46 | ColumnadGenEthernetDslamFlowInterfaceIfIndex | read-create | current | Specifies the IfIndex of the Interface this mapping is tied to. If the value is 0 then this map is not applied to a Interface. This value must be nonzero befor… |
| 1.3.6.1.4.1.664.5.70.2.2.1.47 | ColumnadGenEthernetDslamFlowInterfaceLogicalIndex | read-create | current | Specifies the logical indes within the ifIndex of the ethernet interface. |
| 1.3.6.1.4.1.664.5.70.2.2.1.48 | ColumnadGenEthernetDslamFlowLastErrorString | read-only | current | Returns the reason for the last error. |
| 1.3.6.1.4.1.664.5.70.2.2.1.49 | ColumnadGenEthernetDslamFlowRowStatus | read-create | current | This object is used to create a new row or modify or delete an existing map in this table. A row cannot be set to active until the ethernet interface ifIndex i… |
| 1.3.6.1.4.1.664.5.70.2.2.1.50 | ColumnadGenEthernetDslamFlowNetworkIngressPolicer | read-create | current | Indicate which policer to on network ingress traffic. A value of 0 means no policer is used on network ingress traffic. A non-zero value represents a row from … |
| 1.3.6.1.4.1.664.5.70.2.2.1.51 | ColumnadGenEthernetDslamFlowUpstreamDiscard | read-create | current | Indicate that any packets matching the upstream criteria will be discarded. |
| 1.3.6.1.4.1.664.5.70.2.2.1.53 | ColumnadGenEthernetDslamFlowMaxAllowedMulticastBandwidth | read-create | current | Specify the maximum downstream bandwidth(kbps) available for this flow. This value is only considered if multicast bandwidth is enabled. |
| 1.3.6.1.4.1.664.5.70.2.2.1.54 | ColumnadGenEthernetDslamFlowMaxAllowedMulticastBandwidthEnable | read-create | current | When enabled joins for multicast streams by the subscriber are checked to make sure that the maximum multicast bandwidth will not be exceeded by the join. |
| 1.3.6.1.4.1.664.5.70.2.2.1.55 | ColumnadGenEthernetDslamFlowProfileName | read-create | current | This object is provided so that the user can describe a particular flow by any means desired. This is not related to policers in the adGenEthernetDslamFlowProf… |
| 1.3.6.1.4.1.664.5.70.2.2.1.56 | ColumnadGenEthernetDslamFlowMaxAllowedMcastGroupsEnable | read-create | current | When enabled joins for multicast streams by the subscriber are checked to make sure that the maximum number of non-guarenteed multicast groups will not be exce… |
| 1.3.6.1.4.1.664.5.70.2.2.1.57 | ColumnadGenEthernetDslamFlowNetworkIngressDSCPList | read-create | current | This object is a string used to specify the DSCP values that will be used to classify NetworkIngress traffic. The DSCP values can be specified using both list … |
| 1.3.6.1.4.1.664.5.70.2.2.1.58 | ColumnadGenEthernetDslamFlowCustomerIngressDSCPList | read-create | current | This object is a string used to specify the DSCP values that will be used to classify CustomerIngress traffic. The DSCP values can be specified using both list… |
| 1.3.6.1.4.1.664.5.70.2.2.1.59 | ColumnadGenEthernetDslamFlowIgmpRouterIP | read-create | current | The source IP address that the DSLAM places in IGMP messages destined for the subscriber. This value only applies when IGMP is in proxy mode. |
| 1.3.6.1.4.1.664.5.70.2.2.1.60 | ColumnadGenEthernetDslamFlowActivationStatus | read-only | current | Provides an indication of whether the flow is actually activated. If adGenEthernetDslamFlowRowStatus is not active, this object will return notActivated. When … |
| 1.3.6.1.4.1.664.5.70.2.2.1.61 | ColumnadGenEthernetDslamFlowARPProcessing | read-create | current | Set the ARP processing mode. |
| 1.3.6.1.4.1.664.5.70.2.2.1.62 | ColumnadGenEthernetDslamFlowPPPoEProcessing | read-create | current | Set the PPPoE processing mode. |
| 1.3.6.1.4.1.664.5.70.2.2.1.63 | ColumnadGenEthernetDslamFlowSubscriberIpRowCreateError | read-only | current | Returns the reason for the last row create error on Subscriber Access Static IP Table. |
| 1.3.6.1.4.1.664.5.70.2.2.1.64 | ColumnadGenEthernetDslamFlowDhcpPPPoEVendorNumber | read-create | current | Used to provision the IANA Enterprise Number. This Number is returned by the PPPoE intermediate agent and DHCPv4 relay agent in sub option 9. |
| 1.3.6.1.4.1.664.5.70.2.2.1.65 | ColumnadGenEthernetDslamFlowDhcpPPPoEVendorIdFormat | read-create | current | Used to provision the format of the vendor ID string. This string is returned by the PPPoE intermediate agent and DHCPv4 relay agent in sub option 9. TR-101 st… |
| 1.3.6.1.4.1.664.5.70.2.2.1.66 | ColumnadGenEthernetDslamFlowEvcName | read-create | current | Set the name of the EVC that this flow is connected to. When this object is set, other objects that relate to EVC parameters (e.g. network S-tag, MAC switching… |
| 1.3.6.1.4.1.664.5.70.2.2.1.67 | ColumnadGenEthernetDslamFlowEvcRoot | read-create | current | Indicates whether the mapped interface is connected to the EVC as a root or a leaf. Root interfaces may forward to leaves and other roots; leaf interfaces may … |
| 1.3.6.1.4.1.664.5.70.2.2.1.68 | ColumnadGenEthernetDslamFlowDhcpv6Mode | read-create | current | Set the DHCPv6 processing mode: authenticate(1)- Use DHCPv6 for subscriber authentication block(2)- Discard DHCPv6 transparent(3)- Ignore DHCPv6 snoop(4)- Proc… |
| 1.3.6.1.4.1.664.5.70.2.2.1.69 | ColumnadGenEthernetDslamFlowDhcpv6RelayAgent | read-create | current | Set the DHCPv6 Relay Agent Mode: enabled(1) - enable the relay agent disabled(2) - disable the relay agent sameAsDhcpv4(3) - use the same mode on DHCPv6 Relay … |
| 1.3.6.1.4.1.664.5.70.2.2.1.70 | ColumnadGenEthernetDslamFlowDhcpv6RelayAgentTrusted | read-create | current | Enable/disable DHCPv6 relay agent trusted mode. |
| 1.3.6.1.4.1.664.5.70.2.2.1.71 | ColumnadGenEthernetDslamFlowDhcpPPPoERemoteIdFormat | read-create | current | Used to provision the format of the remote ID string. This string is returned by the DHCPv4 relay agent in option 82 or DHCPv6 relay agent in option 37 or in P… |
| 1.3.6.1.4.1.664.5.70.2.2.1.72 | ColumnadGenEthernetDslamFlowDownstreamQosMapProfile | read-create | current | The attached QoS Map Profile from the adGenQosMapProfileProvisioningTable used to classify downstream traffic into egress queues. An empty string signifies tha… |
| 1.3.6.1.4.1.664.5.70.2.2.1.73 | ColumnadGenEthernetDslamFlowUpstreamChannel | read-create | current | This OID specifies the upstream channel connected to this evc-map. Setting the channel to 0 selects the system default channel. When the evc-map is connected t… |
| 1.3.6.1.4.1.664.5.70.2.2.1.74 | ColumnadGenEthernetDslamFlowDhcpv6CurrMode | read-only | current | View the current DHCPv6 processing mode: Authenticate(1)- Use DHCPv6 for subscriber authentication Block(2)- Discard DHCPv6 Transparent(3)- Ignore DHCPv6 Snoop… |
| 1.3.6.1.4.1.664.5.70.2.2.1.75 | ColumnadGenEthernetDslamFlowDhcpPPPoEVendorIdInsert | read-create | current | Enable/disable Vendor ID information insertion into DHCPv4 Option 82 or DHCPv6 relay agent. Enabling this feature will insert the adGenEthernetDslamFlowDhcpPPP… |
| 1.3.6.1.4.1.664.5.70.2.2.1.76 | ColumnadGenEthernetDslamFlowMatchSourceMacList | read-create | current | Contains a list of source MAC addresses and mask on which to match in the following format: Byte number(s) Description 1 Number of match source MAC address ent… |
| 1.3.6.1.4.1.664.5.70.2.2.1.77 | ColumnadGenEthernetDslamFlowMatchSourceMacLastErrorString | read-only | current | Returns the reason for the last error when setting adGenEthernetDslamFlowMatchSourceMacList or adGenEthernetDslamFlowRev2MatchSourceLastErrorString. |
| 1.3.6.1.4.1.664.5.70.2.2.1.78 | ColumnadGenEthernetDslamFlowMatchNonIp | read-create | current | Enables/disables matching non-IP customer ingress traffic. True - enables match non-IP. False - disables match non-IP. |
| 1.3.6.1.4.1.664.5.70.2.3 | TableadGenEthernetDslamFlowIndexNextTable | not-accessible | current | This table is a read only table that has one row per slot. It returns the next available ethernet dslam flow index to be uses as the index for the EthernetDsla… |
| 1.3.6.1.4.1.664.5.70.2.3.1 | RowadGenEthernetDslamFlowIndexNextEntry | not-accessible | current | An entry in the adGenEthernetDslamFlowIndexNextTable. |
| 1.3.6.1.4.1.664.5.70.2.3.1.1 | ColumnadGenEthernetDslamFlowIndexNext | read-only | current | This variable returns the next available Ethernet Flow Index. |
| 1.3.6.1.4.1.664.5.70.2.4 | TableadGenEthernetDslamFlowProfilesTable | not-accessible | current | The Profile (i.e. Policer) provisioning table. Policers can be created and applied to multiple maps or Interfaces. If a policer is applied to a Interface then … |
| 1.3.6.1.4.1.664.5.70.2.4.1 | RowadGenEthernetDslamFlowProfilesEntry | not-accessible | current | An entry in the Policer provisioning table. |
| 1.3.6.1.4.1.664.5.70.2.4.1.1 | ColumnadGenEthernetDslamFlowProfileIndex | read-only | current | This variable is used as an index into the Policer table. |
| 1.3.6.1.4.1.664.5.70.2.4.1.2 | ColumnadGenEthernetDslamFlowProfileAlias | read-create | current | A user configurable alias for the Policer. Upon creation of the Policer, the associated alias will default to a unique value. |
| 1.3.6.1.4.1.664.5.70.2.4.1.3 | ColumnadGenEthernetDslamFlowProfileCIR | read-create | current | This variable is used to configure the CIR (in kbps). |
| 1.3.6.1.4.1.664.5.70.2.4.1.4 | ColumnadGenEthernetDslamFlowProfileCBS | read-create | current | This variable is used to configure the CBS (in bytes). |
| 1.3.6.1.4.1.664.5.70.2.4.1.5 | ColumnadGenEthernetDslamFlowProfileEIR | read-create | current | This variable is used to configure the EIR (in kbps). A null string is used to configure the EIR for no limit. The maximum CIR value is 100000. |
| 1.3.6.1.4.1.664.5.70.2.4.1.6 | ColumnadGenEthernetDslamFlowProfileEBS | read-create | current | This variable is used to configure the EBS (in bytes). |
| 1.3.6.1.4.1.664.5.70.2.4.1.7 | ColumnadGenEthernetDslamFlowProfileLastErrorString | read-only | current | Returns the reason for the last error. |
| 1.3.6.1.4.1.664.5.70.2.4.1.8 | ColumnadGenEthernetDslamFlowProfileRowStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. |
| 1.3.6.1.4.1.664.5.70.2.4.1.9 | ColumnadGenEthernetDslamFlowProfileActualCIR | read-only | current | This variable shows the actual CIR (in kbps). Policer attributes are set to the closest possible value in hardware based on platform speed, which means the con… |
| 1.3.6.1.4.1.664.5.70.2.4.1.10 | ColumnadGenEthernetDslamFlowProfileActualCBS | read-only | current | This variable shows the actual CBS (in bytes). Policer attributes are set to the closest possible value in hardware based on platform speed, which means the co… |
| 1.3.6.1.4.1.664.5.70.2.4.1.11 | ColumnadGenEthernetDslamFlowProfileActualEIR | read-only | current | This variable shows the actual EIR (in kbps). Policer attributes are set to the closest possible value in hardware based on platform speed, which means the con… |
| 1.3.6.1.4.1.664.5.70.2.4.1.12 | ColumnadGenEthernetDslamFlowProfileActualEBS | read-only | current | This variable shows the actual EBS (in bytes). Policer attributes are set to the closest possible value in hardware based on platform speed, which means the co… |
| 1.3.6.1.4.1.664.5.70.2.5 | TableadGenEthernetDslamFlowNameLookupTable | not-accessible | current | This read-only table allows a lookup from the flow's name and the flow's index. |
| 1.3.6.1.4.1.664.5.70.2.5.1 | RowadGenEthernetDslamFlowNameLookupEntry | not-accessible | current | An entry in the Profile provisioning table. |
| 1.3.6.1.4.1.664.5.70.2.5.1.1 | ColumnadGenEthernetDslamFlowNameLookupName | not-accessible | current | Specifies the name of the flow. |
| 1.3.6.1.4.1.664.5.70.2.5.1.2 | ColumnadGenEthernetDslamFlowNameLookupIndex | read-only | current | Specifies the index of the flow given the name. |
| 1.3.6.1.4.1.664.5.70.2.6 | TableadGenEthernetDslamFlowShaperTable | not-accessible | current | Defines egress shapers applied to ethernet interfaces. |
| 1.3.6.1.4.1.664.5.70.2.6.1 | RowadGenEthernetDslamFlowShaperEntry | not-accessible | current | A shaper indexed by ethernet interface and the set of priorities on that ethernet interface to which it applies. |
| 1.3.6.1.4.1.664.5.70.2.6.1.1 | ColumnadGenEthernetDslamFlowShaperInterfaceLogicalIndex | not-accessible | current | The logical interface index of the ethernet interface to which this shaper applies |
| 1.3.6.1.4.1.664.5.70.2.6.1.2 | ColumnadGenEthernetDslamFlowShaperPrioritySet | not-accessible | current | A bit-mask of priorities to which this shaper applies. Bit 0 indicates queue 0. |
| 1.3.6.1.4.1.664.5.70.2.6.1.3 | ColumnadGenEthernetDslamFlowShaperRate | read-create | current | The peak information rate in kbps of this shaper. Note that for a very short time the units were specified as bps. This was only implemented by a VDSL device, … |
| 1.3.6.1.4.1.664.5.70.2.6.1.4 | ColumnadGenEthernetDslamFlowShaperRowStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. |
| 1.3.6.1.4.1.664.5.70.2.6.1.5 | ColumnadGenEthernetDslamFlowShaperLastErrorString | read-only | current | Returns the reason for the last error. |
| 1.3.6.1.4.1.664.5.70.2.6.1.6 | ColumnadGenEthernetDslamFlowShaperAlias | read-create | current | A user configurable alias for the Shaper. Upon creation of the Shaper, the associated alias will default to a unique value. |
| 1.3.6.1.4.1.664.5.70.2.6.1.7 | ColumnadGenEthernetDslamFlowShaperOperationalStatus | read-only | current | Provides an indication if the shaper is actually running or not. Provides notRunning if the shaper cannot start shaping, provides Running if the shaper is shap… |
| 1.3.6.1.4.1.664.5.70.2.6.1.8 | ColumnadGenEthernetDslamFlowShaperBurstSize | read-create | current | The burst size in bytes, specified for per-port shapers. |
| 1.3.6.1.4.1.664.5.70.2.6.1.9 | ColumnadGenEthernetDslamFlowShaperFixedRate | read-create | current | The fixed rate in kbps of this shaper. This rate is guaranteed, and the interface will generate idle frames to transmit if the rate is not met. This means the … |
| 1.3.6.1.4.1.664.5.70.2.6.1.10 | ColumnadGenEthernetDslamFlowShaperAssuredRate | read-create | current | The assured rate in kbps of this shaper. This rate is guaranteed, but the interface will not generate idle frames if the rate is not met. This means the bandwi… |
| 1.3.6.1.4.1.664.5.70.2.6.1.11 | ColumnadGenEthernetDslamFlowShaperDownstreamMinRate | read-create | current | The downstream min-rate in kbps of this shaper. |
| 1.3.6.1.4.1.664.5.70.2.7 | TableadGenSubscriberAccessStaticIpTable | not-accessible | current | Defines list of subscriber static ip addresses attached on the flow. |
| 1.3.6.1.4.1.664.5.70.2.7.1 | RowadGenSubscriberAccessStaticIpEntry | not-accessible | current | It is indexed by ip address and the flow to which it is attached. |
| 1.3.6.1.4.1.664.5.70.2.7.1.1 | ColumnadGenSubscriberAccessStaticIpAddress | not-accessible | current | The value of the subscriber static ip |
| 1.3.6.1.4.1.664.5.70.2.7.1.2 | ColumnadGenSubscriberAccessStaticIpMacAddress | read-create | current | The subscriber mac address that is associated with this static ip entry. |
| 1.3.6.1.4.1.664.5.70.2.7.1.3 | ColumnadGenSubscriberAccessStaticIpGatewayIp | read-create | current | The subscriber gateway ip address that is associated with this static ip entry |
| 1.3.6.1.4.1.664.5.70.2.7.1.4 | ColumnadGenSubscriberAccessStaticIpGatewayMac | read-create | current | The subscriber gateway mac address that is associated with this static ip entry. |
| 1.3.6.1.4.1.664.5.70.2.7.1.5 | ColumnadGenSubscriberAccessStaticIpLastErrorString | read-only | current | Returns the reason for the last error. |
| 1.3.6.1.4.1.664.5.70.2.7.1.6 | ColumnadGenSubscriberAccessStaticIpRowStatus | read-create | current | This object is used to create a new row or modify or delete an existing row in this table. |
| 1.3.6.1.4.1.664.5.70.2.8 | TableadGenEthernetDslamFlowProfilesIndexNextTable | not-accessible | current | This table is a read only table that has one row per slot. It returns the next available policer index to be used as the index for the Policer table. |
| 1.3.6.1.4.1.664.5.70.2.8.1 | RowadGenEthernetDslamFlowProfilesIndexNextEntry | not-accessible | current | An entry in the adGenEthernetDslamFlowProfilesIndexNextTable. |
| 1.3.6.1.4.1.664.5.70.2.8.1.1 | ColumnadGenEthernetDslamFlowProfilesIndexNext | read-only | current | This variable returns the next available Policer Index. |
| 1.3.6.1.4.1.664.5.70.2.9 | TableadGenEthernetDslamFlowProfilesLookupTable | not-accessible | current | This read-only table allows a lookup from the policer's name and the policer's index. |
| 1.3.6.1.4.1.664.5.70.2.9.1 | RowadGenEthernetDslamFlowProfilesLookupEntry | not-accessible | current | An entry in the policer lookup table. |
| 1.3.6.1.4.1.664.5.70.2.9.1.1 | ColumnadGenEthernetDslamFlowProfileLookupAlias | read-only | current | Specifies the name of the policer. |
| 1.3.6.1.4.1.664.5.70.2.9.1.2 | ColumnadGenEthernetDslamFlowProfileLookupIndex | read-only | current | Specifies the index of the policer given the name. |
| 1.3.6.1.4.1.664.5.70.2.10 | TableadGenEthernetDslamFlowShaperLookupTable | not-accessible | current | This read-only table allows a lookup from the shaper's name and the shaper's index. |
| 1.3.6.1.4.1.664.5.70.2.10.1 | RowadGenEthernetDslamFlowShaperLookupEntry | not-accessible | current | An entry in the shaper lookup table. |
| 1.3.6.1.4.1.664.5.70.2.10.1.1 | ColumnadGenEthernetDslamFlowShaperLookupAlias | read-only | current | Specifies the name of the shaper. |
| 1.3.6.1.4.1.664.5.70.2.10.1.2 | ColumnadGenEthernetDslamFlowShaperLookupIfIndex | read-only | current | Specifies the ifIndex of the shaper given the name |
| 1.3.6.1.4.1.664.5.70.2.10.1.3 | ColumnadGenEthernetDslamFlowShaperLookupInterfaceLogicalIndex | read-only | current | Specifies the logical interface index of the ethernet interface to which this shaper applies given the name |
| 1.3.6.1.4.1.664.5.70.2.10.1.4 | ColumnadGenEthernetDslamFlowShaperLookupPrioritySet | read-only | current | Given the shaper name, specifies a bit-mask of priorities to which this shaper applies. Bit 0 indicates queue 0. |
| 1.3.6.1.4.1.664.5.70.2.11 | TableadGenEthernetDslamFlowRev2Table | not-accessible | current | This table consists of the mapping from a user ethernet interface into an S-Tag or S-Tag/C-Tag. This table returns all interfaces. |
| 1.3.6.1.4.1.664.5.70.2.11.1 | RowadGenEthernetDslamFlowRev2Entry | not-accessible | current | An entry in the adGenEthernetDslamFlowRev2Table. Each entry is an entry in a list of maps that can be applied to a user port. |
| 1.3.6.1.4.1.664.5.70.2.11.1.1 | ColumnadGenEthernetDslamFlowRev2Index | not-accessible | current | Index that specifies an individual map. |
| 1.3.6.1.4.1.664.5.70.2.11.1.2 | ColumnadGenEthernetDslamFlowRev2Name | read-create | current | This object is provided so that the user can identify the ethernet flow uniquely. The profile will be stored in the EMS by name and applied to the user-specifi… |
| 1.3.6.1.4.1.664.5.70.2.11.1.3 | ColumnadGenEthernetDslamFlowRev2TrafficDirection | read-create | current | Specify the traffic direction to which this map applies. Upstream: Customer C-Tag, Pbit, Ethertype, DSCP, and IP Protocol are used to classify traffic upstream… |
| 1.3.6.1.4.1.664.5.70.2.11.1.4 | ColumnadGenEthernetDslamFlowRev2NetworkSTag | read-create | current | Specify the STag seen on network traffic. |
| 1.3.6.1.4.1.664.5.70.2.11.1.5 | ColumnadGenEthernetDslamFlowRev2NetworkCTag | read-create | current | Specify the CTag seen on network ingress/egress traffic. A value of 4095 indicates that no Network CTag is used. A value of 4096 indicates that that the Networ… |
| 1.3.6.1.4.1.664.5.70.2.11.1.6 | ColumnadGenEthernetDslamFlowRev2CEVlan | read-create | current | Specify the CEVlan seen on customer ingress/egress traffic. A value of 4095 indicates that no CEVlan is present. A value of 4097 indicates that customer traffi… |
| 1.3.6.1.4.1.664.5.70.2.11.1.7 | ColumnadGenEthernetDslamFlowRev2DownstreamForwardingMode | read-create | current | Specify how ethernet frames on this flow are forwarded through the switch. This value is bitmasked so that forwarding modes can be combined. src (0x1) - Use th… |
| 1.3.6.1.4.1.664.5.70.2.11.1.8 | ColumnadGenEthernetDslamFlowRev2DownstreamPbitMethod | read-create | current | Specify the PBit mapping mode in from the network to customer. Inherit - downstream traffic should egress the Interface with the priority from the network. Mar… |
| 1.3.6.1.4.1.664.5.70.2.11.1.9 | ColumnadGenEthernetDslamFlowRev2DownstreamPbitMarking | read-create | current | If the network Pbit mode is marked then this variable specifies the downstream pBit. |
| 1.3.6.1.4.1.664.5.70.2.11.1.10 | ColumnadGenEthernetDslamFlowRev2DownstreamPbitMapping | read-create | current | If the network Pbit mode is mapped then this variable specifies the ingress/egress priority mapping index. |
| 1.3.6.1.4.1.664.5.70.2.11.1.11 | ColumnadGenEthernetDslamFlowRev2NetworkIngressPbit | read-create | current | This option is a bitmask used to specify a list of allowable P-bit values of the S-Tag ingressing from the network. A value of 255 indicates that this value is… |
| 1.3.6.1.4.1.664.5.70.2.11.1.12 | ColumnadGenEthernetDslamFlowRev2NetworkIngressEtherType | read-create | current | Specify the EtherType value that will be used to classify NetworkIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.11.1.13 | ColumnadGenEthernetDslamFlowRev2NetworkIngressDSCP | read-create | current | Specify a single DSCP value that will be used to classify NetworkIngress traffic. A value of 64 indicates this filter is disabled. If multiple DSCP values shou… |
| 1.3.6.1.4.1.664.5.70.2.11.1.14 | ColumnadGenEthernetDslamFlowRev2NetworkIngressIPProtocolID | read-create | current | Specify the IP Protocol ID that will be used to classify NetworkIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.11.1.15 | ColumnadGenEthernetDslamFlowRev2UpstreamForwardingMode | read-create | current | Specify how ethernet frames on this flow are forwarded through the switch. This value is bitmasked so that forwarding modes can be combined. src (0x1) - Use th… |
| 1.3.6.1.4.1.664.5.70.2.11.1.16 | ColumnadGenEthernetDslamFlowRev2UpstreamSTagPbitMethod | read-create | current | Specify the PBit mapping mode in from the Customer to Network STag. Inherit - upstream STags should egress with the priority from the customer. Marked - upstre… |
| 1.3.6.1.4.1.664.5.70.2.11.1.17 | ColumnadGenEthernetDslamFlowRev2UpstreamSTagPbitMarking | read-create | current | If the Customer Pbit mode is marked then this variable specifies the upstream STag pBit. |
| 1.3.6.1.4.1.664.5.70.2.11.1.18 | ColumnadGenEthernetDslamFlowRev2UpstreamSTagPbitMapping | read-create | current | If the Customer Pbit mode is mapped then this variable specifies the ingress/egress STag priority mapping index. |
| 1.3.6.1.4.1.664.5.70.2.11.1.19 | ColumnadGenEthernetDslamFlowRev2UpstreamCTagPbitMethod | read-create | current | Specify the CTag PBit mapping mode in from the Customer to Network. Inherit - upstream traffic should egress with the priority from the customer. Marked - upst… |
| 1.3.6.1.4.1.664.5.70.2.11.1.20 | ColumnadGenEthernetDslamFlowRev2UpstreamCTagPbitMarking | read-create | current | If the Customer Pbit mode is marked then this variable specifies the upstream CTag pBit. |
| 1.3.6.1.4.1.664.5.70.2.11.1.21 | ColumnadGenEthernetDslamFlowRev2UpstreamCTagPbitMapping | read-create | current | If the Customer Pbit mode is mapped then this variable specifies the ingress/egress CTag priority mapping index. |
| 1.3.6.1.4.1.664.5.70.2.11.1.22 | ColumnadGenEthernetDslamFlowRev2CustomerIngressPbit | read-create | current | This option is a bitmask used to specify a list of allowable P-bit values of the CEVlan ingressing from the customer. A value of 255 indicates that this value … |
| 1.3.6.1.4.1.664.5.70.2.11.1.23 | ColumnadGenEthernetDslamFlowRev2CustomerIngressEtherType | read-create | current | Specify the EtherType value that will be used to classify CustomerIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.11.1.24 | ColumnadGenEthernetDslamFlowRev2CustomerIngressDSCP | read-create | current | Specify a single DSCP value that will be used to classify CustomerIngress traffic. A value of 64 indicates this filter is disabled. If multiple DSCP values sho… |
| 1.3.6.1.4.1.664.5.70.2.11.1.25 | ColumnadGenEthernetDslamFlowRev2CustomerIngressIPProtocolID | read-create | current | Specify the IP Protocol ID that will be used to classify CustomerIngress traffic. A value of 0x0000 indicates this filter is disabled. |
| 1.3.6.1.4.1.664.5.70.2.11.1.26 | ColumnadGenEthernetDslamFlowRev2CustomerIngressBroadcast | read-create | current | This variable specifies whether or not to drop CustomerIngress broadcasts on this map. |
| 1.3.6.1.4.1.664.5.70.2.11.1.27 | ColumnadGenEthernetDslamFlowRev2CustomerIngressMulticast | read-create | current | This variable specifies whether or not to drop CustomerIngress multicasts on this map. |
| 1.3.6.1.4.1.664.5.70.2.11.1.28 | ColumnadGenEthernetDslamFlowRev2CustomerIngressUnicast | read-create | current | This variable specifies whether or not to drop CustomerIngress unicasts on this map. |
| 1.3.6.1.4.1.664.5.70.2.11.1.29 | ColumnadGenEthernetDslamFlowRev2CustomerIngressPolicer | read-create | current | Indicate which policer to on customer ingress traffic. A value of 0 means no policer is used on customer ingress traffic. A non-zero value represents a row fro… |
| 1.3.6.1.4.1.664.5.70.2.11.1.30 | ColumnadGenEthernetDslamFlowRev2EncapsMode | read-create | current | Encapsulation mode/type if applicable; 'notApplicable' otherwise. IPoE and PPPoE specify a particular protocol over ethernet. 'Ethernet' specifies that any pro… |
| 1.3.6.1.4.1.664.5.70.2.11.1.31 | ColumnadGenEthernetDslamFlowRev2ManualAddrAging | read-create | current | Manual Address Aging in minutes for unicast MACs. |
| 1.3.6.1.4.1.664.5.70.2.11.1.32 | ColumnadGenEthernetDslamFlowRev2IntermedAgent | read-create | current | Enable/disable Intermediate Agent if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.11.1.33 | ColumnadGenEthernetDslamFlowRev2DhcpRelay | read-create | current | Set the DHCPv4 processing mode: Enabled(1)- Use DHCPv4 for subscriber authentication Disabled(2)- Discard DHCPv4 Not Applicable(3)- Unused Transparent(4)- Igno… |
| 1.3.6.1.4.1.664.5.70.2.11.1.34 | ColumnadGenEthernetDslamFlowRev2Option82Insert | read-create | current | Enable/disable Option 82 Insertion if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.11.1.35 | ColumnadGenEthernetDslamFlowRev2LearnedIpAddrAgingMethod | read-create | current | Method for Learned IP Address Aging if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.11.1.36 | ColumnadGenEthernetDslamFlowRev2IgmpProcessing | read-create | current | Method for IGMP Processing if applicable; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.11.1.37 | ColumnadGenEthernetDslamFlowRev2IgmpVersion | read-create | current | IGMP Version if applicable: v3 implies v1, v2, and v3; v2 implies v1 and v2; v1 is v1 only; 'notApplicable' otherwise. |
| 1.3.6.1.4.1.664.5.70.2.11.1.38 | ColumnadGenEthernetDslamFlowRev2LastMemberQueryInterval | read-create | current | Last Member Query Interval in milliseconds. This is the amount of time between Queries. Low value results in faster detection of missed leaves. |
| 1.3.6.1.4.1.664.5.70.2.11.1.39 | ColumnadGenEthernetDslamFlowRev2LastMemberQueryCount | read-create | current | Last Member Query Count. This is the number of queries before declaring no membership of a group (channel). |
| 1.3.6.1.4.1.664.5.70.2.11.1.40 | ColumnadGenEthernetDslamFlowRev2ImmediateLeave | read-create | current | Enable/disable Immediate Leave if applicable; 'notApplicable' otherwise. Disable is the equivalent of setting Last Member Query Count to 0. |
| 1.3.6.1.4.1.664.5.70.2.11.1.41 | ColumnadGenEthernetDslamFlowRev2MaxAllowedMcastGroups | read-create | current | Maximum Allowed Non-Guaranteed Multicast Groups. This value is only considered if multicast groups are enabled. |
| 1.3.6.1.4.1.664.5.70.2.11.1.42 | ColumnadGenEthernetDslamFlowRev2DhcpPPPoERemoteId | read-create | current | Enable/disable Remote ID insertion into DHCPv4 Option 82 or DHCPv6 relay agent in option 37 or PPPoE Vendor Specific tag if applicable. |
| 1.3.6.1.4.1.664.5.70.2.11.1.43 | ColumnadGenEthernetDslamFlowRev2DhcpPPPoELoopCharacteristics | read-create | current | Enable/disable loop characteristics insertion into DHCPv4 Option 82 or DHCPv6 relay agent option 17 (vendor specific) loop characteristics or PPPoE Vendor Spec… |
| 1.3.6.1.4.1.664.5.70.2.11.1.44 | ColumnadGenEthernetDslamFlowRev2DhcpPPPoECircuitIdFormat | read-create | current | Used to provision the format of the circuit ID string. This string is returned by the PPPoE intermediate agent and DHCP relay agent in v4 sub option 1 or in v6… |
| 1.3.6.1.4.1.664.5.70.2.11.1.45 | ColumnadGenEthernetDslamFlowRev2PPPoASessionTimeout | read-create | current | Used to set the PPPoA Session timeout when the mapping is provisioned for PPPoA encapsulation. |
| 1.3.6.1.4.1.664.5.70.2.11.1.46 | ColumnadGenEthernetDslamFlowRev2InterfaceIfIndex | read-create | current | Specifies the IfIndex of the Interface this mapping is tied to. If the value is 0 then this map is not applied to a Interface. This value must be nonzero befor… |
| 1.3.6.1.4.1.664.5.70.2.11.1.47 | ColumnadGenEthernetDslamFlowRev2InterfaceLogicalIndex | read-create | current | Specifies the logical indes within the ifIndex of the ethernet interface. |
| 1.3.6.1.4.1.664.5.70.2.11.1.48 | ColumnadGenEthernetDslamFlowRev2LastErrorString | read-only | current | Returns the reason for the last error. |
| 1.3.6.1.4.1.664.5.70.2.11.1.49 | ColumnadGenEthernetDslamFlowRev2RowStatus | read-create | current | This object is used to create a new row or modify or delete an existing map in this table. A row cannot be set to active until the ethernet interface ifIndex i… |
| 1.3.6.1.4.1.664.5.70.2.11.1.50 | ColumnadGenEthernetDslamFlowRev2NetworkIngressPolicer | read-create | current | Indicate which policer to on network ingress traffic. A value of 0 means no policer is used on network ingress traffic. A non-zero value represents a row from … |
| 1.3.6.1.4.1.664.5.70.2.11.1.51 | ColumnadGenEthernetDslamFlowRev2UpstreamDiscard | read-create | current | Indicate that any packets matching the upstream criteria will be discarded. |
| 1.3.6.1.4.1.664.5.70.2.11.1.53 | ColumnadGenEthernetDslamFlowRev2MaxAllowedMulticastBandwidth | read-create | current | Specify the maximum downstream bandwidth(kbps) available for this flow. This value is only considered if multicast bandwidth is enabled. |
| 1.3.6.1.4.1.664.5.70.2.11.1.54 | ColumnadGenEthernetDslamFlowRev2MaxAllowedMulticastBandwidthEnable | read-create | current | When enabled joins for multicast streams by the subscriber are checked to make sure that the maximum multicast bandwidth will not be exceeded by the join. |
| 1.3.6.1.4.1.664.5.70.2.11.1.55 | ColumnadGenEthernetDslamFlowRev2ProfileName | read-create | current | This object is provided so that the user can describe a particular flow by any means desired. This is not related to policers in the adGenEthernetDslamFlowRev2… |
| 1.3.6.1.4.1.664.5.70.2.11.1.56 | ColumnadGenEthernetDslamFlowRev2MaxAllowedMcastGroupsEnable | read-create | current | When enabled joins for multicast streams by the subscriber are checked to make sure that the maximum number of non-guarenteed multicast groups will not be exce… |
| 1.3.6.1.4.1.664.5.70.2.11.1.57 | ColumnadGenEthernetDslamFlowRev2NetworkIngressDSCPList | read-create | current | This object is a string used to specify the DSCP values that will be used to classify NetworkIngress traffic. The DSCP values can be specified using both list … |
| 1.3.6.1.4.1.664.5.70.2.11.1.58 | ColumnadGenEthernetDslamFlowRev2CustomerIngressDSCPList | read-create | current | This object is a string used to specify the DSCP values that will be used to classify CustomerIngress traffic. The DSCP values can be specified using both list… |
| 1.3.6.1.4.1.664.5.70.2.11.1.59 | ColumnadGenEthernetDslamFlowRev2IgmpRouterIP | read-create | current | The source IP address that the DSLAM places in IGMP messages destined for the subscriber. This value only applies when IGMP is in proxy mode. |
| 1.3.6.1.4.1.664.5.70.2.11.1.60 | ColumnadGenEthernetDslamFlowRev2ActivationStatus | read-only | current | Provides an indication of whether the flow is actually activated. If adGenEthernetDslamFlowRev2RowStatus is not active, this object will return notActivated. W… |
| 1.3.6.1.4.1.664.5.70.2.11.1.61 | ColumnadGenEthernetDslamFlowRev2ARPProcessing | read-create | current | Set the ARP processing mode. |
| 1.3.6.1.4.1.664.5.70.2.11.1.62 | ColumnadGenEthernetDslamFlowRev2PPPoEProcessing | read-create | current | Set the PPPoE processing mode. |
| 1.3.6.1.4.1.664.5.70.2.11.1.63 | ColumnadGenEthernetDslamFlowRev2SubscriberIpRowCreateError | read-only | current | Returns the reason for the last row create error on Subscriber Access Static IP Table. |
| 1.3.6.1.4.1.664.5.70.2.11.1.64 | ColumnadGenEthernetDslamFlowRev2DhcpPPPoEVendorNumber | read-create | current | Used to provision the IANA Enterprise Number. This Number is returned by the PPPoE intermediate agent and DHCPv4 relay agent in sub option 9. |
| 1.3.6.1.4.1.664.5.70.2.11.1.65 | ColumnadGenEthernetDslamFlowRev2DhcpPPPoEVendorIdFormat | read-create | current | Used to provision the format of the vendor ID string. This string is returned by the PPPoE intermediate agent and DHCPv4 relay agent in sub option 9. TR-101 st… |
| 1.3.6.1.4.1.664.5.70.2.11.1.66 | ColumnadGenEthernetDslamFlowRev2EvcName | read-create | current | Set the name of the EVC that this flow is connected to. When this object is set, other objects that relate to EVC parameters (e.g. network S-tag, MAC switching… |
| 1.3.6.1.4.1.664.5.70.2.11.1.67 | ColumnadGenEthernetDslamFlowRev2EvcRoot | read-create | current | Indicates whether the mapped interface is connected to the EVC as a root or a leaf. Root interfaces may forward to leaves and other roots; leaf interfaces may … |
| 1.3.6.1.4.1.664.5.70.2.11.1.68 | ColumnadGenEthernetDslamFlowRev2Dhcpv6Mode | read-create | current | Set the DHCPv6 processing mode: Authenticate(1)- Use DHCPv6 for subscriber authentication Block(2)- Discard DHCPv6 Transparent(3)- Ignore DHCPv6 Snoop(4)- Proc… |
| 1.3.6.1.4.1.664.5.70.2.11.1.69 | ColumnadGenEthernetDslamFlowRev2Dhcpv6RelayAgent | read-create | current | Set the DHCPv6 Relay Agent Mode: enabled(1) - enable the relay agent disabled(2) - disable the relay agent sameAsDhcpv4(3) - use the same mode on DHCPv6 Relay … |
| 1.3.6.1.4.1.664.5.70.2.11.1.70 | ColumnadGenEthernetDslamFlowRev2Dhcpv6RelayAgentTrusted | read-create | current | Enable/disable DHCPv6 relay agent trusted mode. |
| 1.3.6.1.4.1.664.5.70.2.11.1.71 | ColumnadGenEthernetDslamFlowRev2DhcpPPPoERemoteIdFormat | read-create | current | Used to provision the format of the remote ID string. This string is returned by the DHCPv4 relay agent in option 82 or DHCPv6 relay agent in option 37 or in P… |
| 1.3.6.1.4.1.664.5.70.2.11.1.72 | ColumnadGenEthernetDslamFlowRev2DownstreamQosMapProfile | read-create | current | The attached QoS Map Profile from the adGenQosMapProfileProvisioningTable used to classify downstream traffic into egress queues. An empty string signifies tha… |
| 1.3.6.1.4.1.664.5.70.2.11.1.73 | ColumnadGenEthernetDslamFlowRev2Dhcpv6CurrMode | read-only | current | View the current DHCPv6 processing mode: Authenticate(1)- Use DHCPv6 for subscriber authentication Block(2)- Discard DHCPv6 Transparent(3)- Ignore DHCPv6 Snoop… |
| 1.3.6.1.4.1.664.5.70.2.11.1.74 | ColumnadGenEthernetDslamFlowRev2MatchSourceMacList | read-create | current | Contains a list of source MAC addresses and mask on which to match in the following format: Byte number(s) Description 1 Number of match source MAC address ent… |
| 1.3.6.1.4.1.664.5.70.2.11.1.75 | ColumnadGenEthernetDslamFlowRev2MatchSourceMacLastErrorString | read-only | current | Returns the reason for the last error when setting adGenEthernetDslamFlowMatchSourceMacList or adGenEthernetDslamFlowRev2MatchSourceLastErrorString. |
| 1.3.6.1.4.1.664.5.70.2.11.1.76 | ColumnadGenEthernetDslamFlowRev2MatchNonIp | read-create | current | Enables/disables matching non-IP customer ingress traffic. True - enables match non-IP. False - disables match non-IP. |
| 1.3.6.1.4.1.664.5.70.2.12 | TableadGenEthernetDslamFlowRev2NameLookupTable | not-accessible | current | This read-only table allows a lookup from the flow's name and the flow's index. |
| 1.3.6.1.4.1.664.5.70.2.12.1 | RowadGenEthernetDslamFlowRev2NameLookupEntry | not-accessible | current | An entry in the Profile provisioning table. |
| 1.3.6.1.4.1.664.5.70.2.12.1.1 | ColumnadGenEthernetDslamFlowRev2NameLookupName | not-accessible | current | Specifies the name of the flow. |
| 1.3.6.1.4.1.664.5.70.2.12.1.2 | ColumnadGenEthernetDslamFlowRev2NameLookupIndex | read-only | current | Specifies the index of the flow given the name. |
| 1.3.6.1.4.1.664.5.70.2.13 | TableadGenEthernetDslamFlowRev2IndexNextTable | not-accessible | current | This table is a read only table that has one row per slot. It returns the next available ethernet dslam flow index to be uses as the index for the EthernetDsla… |
| 1.3.6.1.4.1.664.5.70.2.13.1 | RowadGenEthernetDslamFlowRev2IndexNextEntry | not-accessible | current | An entry in the adGenEthernetDslamFlowRev2IndexNextTable. |
| 1.3.6.1.4.1.664.5.70.2.13.1.1 | ColumnadGenEthernetDslamFlowRev2IndexNext | read-only | current | This variable returns the next available Ethernet Flow Index. |
| 1.3.6.1.4.1.664.5.70.2.14 | TableadGenEthernetDslamFlowQueueTable | not-accessible | current | This table is a read only table that has one row per slot. It returns the queue information for a slot. |
| 1.3.6.1.4.1.664.5.70.2.14.1 | RowadGenEthernetDslamFlowQueueTableEntry | not-accessible | current | An entry in the adGenEthernetDslamFlowQueueTable. |
| 1.3.6.1.4.1.664.5.70.2.14.1.1 | ColumnadGenEthernetDslamFlowHonorsSystemPbitCosMap | read-only | current | Indicates whether a slot is currently honoring the system's P-bit to CoS mapping. |
| 1.3.6.1.4.1.664.5.70.2.14.1.2 | ColumnadGenEthernetDslamFlowShaperQueuePriorityOrder | read-only | current | Indicates for SNMP whether adGenEthernetDslamFlowShaperPrioritySet is represented with the left-most bit representing the highest priority queue or the right-m… |
| 1.3.6.1.4.1.664.5.70.2.15 | NodeadGenEthernetDslamFlowAlarmsPrefix | |||
| 1.3.6.1.4.1.664.5.70.2.15.0 | NodeadGenEthernetDslamFlowAlarms | |||
| 1.3.6.1.4.1.664.5.70.2.15.0.1 | NotificationadGenEthernetDslamFlowDuplicateMacDetectedClr | current | Duplicate MAC address detected on the interface - Cleared. | |
| 1.3.6.1.4.1.664.5.70.2.15.0.2 | NotificationadGenEthernetDslamFlowDuplicateMacDetectedAct | current | Duplicate MAC address detected on the interface - Active. | |
| 1.3.6.1.4.1.664.5.70.2.15.0.3 | NotificationadGenEthernetDslamFlowMacAllocationAlarmClr | current | Maximum MACs per Slot Allocated - Cleared. | |
| 1.3.6.1.4.1.664.5.70.2.15.0.4 | NotificationadGenEthernetDslamFlowMacAllocationAlarmAct | current | Maximum MACs per Slot Allocated - Active. | |
| 1.3.6.1.4.1.664.5.70.2.16 | TableadGenEthernetDslamFlowScalarTable | not-accessible | current | This table is a read only table that has one row per slot. It returns the scalar information for a slot. |
| 1.3.6.1.4.1.664.5.70.2.16.1 | RowadGenEthernetDslamFlowScalarTableEntry | not-accessible | current | An entry in the adGenEthernetDslamFlowScalarTable. |
| 1.3.6.1.4.1.664.5.70.2.16.1.1 | ColumnadGenEthernetFlowMatchSourceMacMaxAddresses | read-only | current | Indicates the maximum number of match source MAC addresses allowed. |
| 1.3.6.1.4.1.664.5.70.2.17 | TableadGenEthernetDslamFlowLoggingTable | not-accessible | current | This table is for enabling/disabling DHCP and PPPoE debug from event log and has one row per slot. |
| 1.3.6.1.4.1.664.5.70.2.17.1 | RowadGenEthernetDslamFlowLoggingEntry | not-accessible | current | An entry in the adGenEthernetDslamFlowLoggingTable. |
| 1.3.6.1.4.1.664.5.70.2.17.1.1 | ColumnadGenEthernetDslamFlowDhcpPppoeEventDebug | read-create | current | Enables/disables extraneous DHCP and PPPoE debug from event log. 1 = Enabled 2 = Disabled |
| 1.3.6.1.4.1.664.6.10000.70.2.2 | IdentityadGenEthernetDslamFlowMIB | This MIB defines the objects for the Ethernet Flow MIB. |