CISCO-CAS-IF-EXT-MIB
231 objects
The MIB module is an extension of CISCO-CAS-IF-MIB. It defines the attributes of a voice interface.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.314 | IdentityciscoCasIfExtMIB | The MIB module is an extension of CISCO-CAS-IF-MIB. It defines the attributes of a voice interface. | ||
| 1.3.6.1.4.1.9.9.314.0 | NodeciscoCasIfExtMIBNotifications | |||
| 1.3.6.1.4.1.9.9.314.1 | NodeciscoCasIfExtMIBObjects | |||
| 1.3.6.1.4.1.9.9.314.1.1 | NodeccasIfExtConfig | |||
| 1.3.6.1.4.1.9.9.314.1.1.1 | TableccasIfExtVoiceCfgTable | not-accessible | current | The voice interface extended table defines the parameters related to the configuration of voice interfaces (DS0 group of DS1). This table extends the ccasVoice… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1 | RowccasIfExtVoiceCfgEntry | not-accessible | current | Each entry represents a voice interface (DS0 group of DS1) in a media gateway. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.1 | ColumnccasIfExtVoiceCfgLifNumber | read-write | current | This object specifies the LIF (Logical InterFace) number associated with this voice interface. If this object is set to 0, this interface does not have an asso… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.2 | ColumnccasIfExtVoiceCfgCcntrlProfile | read-write | current | This object specifies the index of call control profile that is used by this DS0 group. If the value of ccasGrpCfgServiceType is 'mgcp(6)', this is the index o… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.3 | ColumnccasIfExtVoiceCfgVadEnabled | read-write | current | The object specifies VAD (Voice Activity Detection) is enabled for the compression DSPs of this interface. The value of this object is 'false' if the voice int… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.4 | ColumnccasIfExtVoiceCfgContinuityTone1 | read-write | current | The object specifies the first frequency tone to be sent between the terminating and the originating gateways in the continuity test. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.5 | ColumnccasIfExtVoiceCfgContinuityTone2 | read-write | current | The object specifies the second frequency tone to be sent between the terminating and the originating gateways in the continuity test. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.6 | ColumnccasIfExtVoiceCfgModemPassThru | read-write | current | This object specifies the modem pass-through mode: (1) passThruDisabled: Modem pass-through is disabled (2) passThruCisco: Cisco Proprietary PV (Protocol Viola… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.7 | ColumnccasIfExtVoiceCfgUpspeedCodec | read-write | current | This object specifies the CODEC type to use for modem upspeed. Upspeed is to change the transmission rate of the voice interface to a higher rate of CODEC type. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.8 | ColumnccasIfExtVoiceCfgT38MaxFaxTxRate | read-write | deprecated | This object specifies the maximum FAX relay transmission rate. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.9 | ColumnccasIfExtVoiceCfgT38HsPktPeriod | read-write | deprecated | This object specifies the period of time for primary high speed (HS) data packet. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.10 | ColumnccasIfExtVoiceCfgT38HsRedundancy | read-write | deprecated | The object specifies the number of redundant FAX packets for Internet FAX protocol (IFP) packet transmission. The value of '0' indicates that no redundant Inte… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.11 | ColumnccasIfExtVoiceCfgRepetition | read-write | current | This object is used to repeatedly apply the writable objects of ccasIfExtVoiceCfgTable specified in the same SNMP PDU starting from the row specifies by the in… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.12 | ColumnccasIfExtVoiceCfgBulkCfgOwner | read-write | current | This object is used for error checking of the operation specified in ccasIfExtVoiceCfgRepetition. The value of this object is set by the SNMP manager with its … |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.13 | ColumnccasIfExtVoiceCfgBulkCfgResult | read-only | current | This object is used for error checking of the operation specified in ccasIfExtVoiceCfgRepetition. This object indicates the result of the bulk configuration in… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.14 | ColumnccasIfExtVoiceCfgVadTimer | read-write | current | This object specifies the hangover time for VAD. Once the voice inactivity is detected, gateway will wait for this duration before activating silence suppressi… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.15 | ColumnccasIfExtVoiceCfgICSEnable | read-write | current | This object specifies whether the Idle Channel suppression (ICS) is enabled for an AAL2 connection. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.16 | ColumnccasIfExtVoiceCfgICSIntTimer | read-write | current | This object specifies a timeout value for ICS integration timer. This timer is started once channel idle is detected. When the timer is expired, the gateway wi… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.17 | ColumnccasIfExtVoiceCfgTonePlan | read-write | current | This object specifies which tone plan the DS0 group is using for playing the tones. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.18 | ColumnccasIfExtVoiceCfgGwyLinkId | read-write | current | This object specifies the H.248 media gateway link that this DS0 group belongs to. This object is applicable only if the value of ccasGrpCfgServiceType is 'h24… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.19 | ColumnccasIfExtVoiceCfgH248PkgIds | read-write | current | This object specifies the H.248 packages supported in this DS0 group. This object is applicable only if the value of ccasGrpCfgServiceType is 'h248(9)'. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.20 | ColumnccasIfExtVoiceCfgEventMappingIdx | read-write | current | This object specifies the action of the voice band data signal events handling in this DS0 group. The real-time detected voice band data events are categorized… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.21 | ColumnccasIfExtVoiceCfgGatewayIndex | read-write | current | This object specifies the media gateway index that this DS0 group belong to. The value of this object is cmgwIndex in cMediaGwTable. |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.22 | ColumnccasIfExtVoiceCfgCasProfile | read-write | current | This object specifies the index of CAS profile that is used by this DS0 group. The value of this object is ccasProfileIndex in ccasIfExtProfileTable. This obje… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.23 | ColumnccasIfExtVoiceCfgCasVariant | read-write | current | This object specifies the index of CAS variant that is used by this DS0 group. The value of this object is the same as the value of ccasVariantIndex in ccasIfE… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.24 | ColumnccasIfExtVoiceCfgDs0ChannelsFail | read-only | current | This object contains the bit map of the failure DS0 channels in the DS0 group. The MSB (most significant bit) is DS0 channel number 1. For T1, only higher 24 b… |
| 1.3.6.1.4.1.9.9.314.1.1.1.1.25 | ColumnccasIfExtVoiceCfgNoiseRegType | read-write | current | This object specifies the type of comfort noise generation: (1) none: No comfort noise generation (2) simple: Cisco Proprietary comfort noise generation (3) g7… |
| 1.3.6.1.4.1.9.9.314.1.1.3 | TableccasIfExtDs0GrpCfgTable | not-accessible | current | The voice interface extended table defines the parameters related to the configuration of voice interfaces (DS0 group of DS1). This table extends the ccasVoice… |
| 1.3.6.1.4.1.9.9.314.1.1.3.1 | RowccasIfExtDs0GrpCfgEntry | not-accessible | current | Each entry represents a DS0 group interface. |
| 1.3.6.1.4.1.9.9.314.1.1.3.1.1 | ColumnccasIfExtDs0GrpRepetition | read-write | current | This object is used to repeatedly apply the writable objects of ccasIfExtDs0GrpCfgTable specified in the same SNMP PDU starting from the row specifies by the i… |
| 1.3.6.1.4.1.9.9.314.1.1.3.1.2 | ColumnccasIfExtDs0GrpRepeatOwner | read-write | current | This object is used for error checking of the operation specified in ccasIfExtDs0GrpRepetition. The value of this object is set by the SNMP manager with its ow… |
| 1.3.6.1.4.1.9.9.314.1.1.3.1.3 | ColumnccasIfExtDs0GrpRepeatResult | read-only | current | This object is used for error checking of the operation specified in ccasIfExtDs0GrpRepetition. This object indicates the result of the repetition initiated by… |
| 1.3.6.1.4.1.9.9.314.1.2 | NodeccasIfExtProfile | |||
| 1.3.6.1.4.1.9.9.314.1.2.1 | TableccasIfExtProfileTable | not-accessible | current | This table specifies a list of CAS profiles. Each CAS profile consists of the configurable CAS attributes related to: . Line signal timers table, ccasIfExtLine… |
| 1.3.6.1.4.1.9.9.314.1.2.1.1 | RowccasIfExtProfileEntry | not-accessible | current | Each entry represents a CAS profile in media gateway. |
| 1.3.6.1.4.1.9.9.314.1.2.1.1.1 | ColumnccasProfileIndex | not-accessible | current | This object uniquely identifies the CAS profile. The value of 1 specifies the default CAS profile in the media gateway. |
| 1.3.6.1.4.1.9.9.314.1.2.1.1.2 | ColumnccasProfileLineSigTimer | read-create | current | This object specifies the attributes of CAS line signaling timers indicated by ccasLSTIndex in ccasIfExtLineSignalTimerTable. |
| 1.3.6.1.4.1.9.9.314.1.2.1.1.3 | ColumnccasProfileRegisterSignal | read-create | current | This object specifies the attributes of CAS register signals indicated by ccasRSIndex in ccasIfExtRegisterSignalTable. |
| 1.3.6.1.4.1.9.9.314.1.2.1.1.4 | ColumnccasProfileRegSigTimer | read-create | current | This object specifies the attributes of CAS register signaling timers indicated by ccasRSTIndex in ccasIfExtRegSignalTimerTable. |
| 1.3.6.1.4.1.9.9.314.1.2.1.1.5 | ColumnccasProfileGeneralCfg | read-create | current | This object specifies the general CAS attributes indicated by ccasGCnfIndex in ccasIfExtGeneralConfigTable. |
| 1.3.6.1.4.1.9.9.314.1.2.1.1.6 | ColumnccasProfileRowStatus | read-create | current | When the entry is created, all the associated entries indexed by the following objects must be existing: ccasProfileLineSigTimer, ccasProfileRegisterSignal, cc… |
| 1.3.6.1.4.1.9.9.314.1.2.2 | TableccasIfExtVariantTable | not-accessible | current | This table specifies a list of CAS signaling protocols such as R2 CAS, Feature Group D Oprerator Services ( FGD OS). Each CAS variant is downloaded to and pars… |
| 1.3.6.1.4.1.9.9.314.1.2.2.1 | RowccasIfExtVariantEntry | not-accessible | current | Each entry represents a CAS variant in media gateway. Upon the creation of the entry, the CAS variant specified by ccasVariantFile will be downloaded to the me… |
| 1.3.6.1.4.1.9.9.314.1.2.2.1.1 | ColumnccasVariantIndex | not-accessible | current | An arbitrary value which uniquely identifies the CAS variant in the media gateway. |
| 1.3.6.1.4.1.9.9.314.1.2.2.1.2 | ColumnccasVariantFile | read-create | current | This object specifies the valid file name with extension '.o' stored on the media gateway's hard disk. The CAS variant file can be transferred to the media gat… |
| 1.3.6.1.4.1.9.9.314.1.2.2.1.3 | ColumnccasVariantSource | read-create | current | This object specifies the source from where the CAS variant file must be fetched. . internal: Value indicates that the file is built into the firmware. . exter… |
| 1.3.6.1.4.1.9.9.314.1.2.2.1.4 | ColumnccasVariantNumberCount | read-only | current | This object indicates the number of DS0 groups of the DS1 line which are used for the CAS variant. |
| 1.3.6.1.4.1.9.9.314.1.2.2.1.5 | ColumnccasVariantState | read-only | current | This object indicates the configuration status of the CAS variant. . initInProgress: The state machine is being initialized. . initSuccessfully: The state mach… |
| 1.3.6.1.4.1.9.9.314.1.2.2.1.6 | ColumnccasVariantRowStatus | read-create | current | When the entry is created, the ccasVariantFile object is mandatory. The entry can be added or deleted, but not modified by the manager. |
| 1.3.6.1.4.1.9.9.314.1.3 | NodeccasIfExtConfigLineSignal | |||
| 1.3.6.1.4.1.9.9.314.1.3.1 | TableccasIfExtIncomingLineSignalTable | not-accessible | current | This table defines the parameters related to the incoming line signals for CAS variant. The appropriate signal definitions from this table will be downloaded t… |
| 1.3.6.1.4.1.9.9.314.1.3.1.1 | RowccasIfExtIncomingLineSignalEntry | not-accessible | current | Each entry represents an incoming line signal definition for the CAS variant corresponding to the CAS Variant index. Entries in this table are implicitly creat… |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.2 | ColumnccasILSSignalNameIndex | not-accessible | current | This object specifies the Signal Name index for the various CAS line signals. This object along with the cmgwIndex and ccasVariantIndex identify an unique entr… |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.3 | ColumnccasILSSignalName | read-only | current | This object indicates CAS signal name corresponding to the ccasILSSignalNameIndex. The media gateway uses ccasILSRxPattern along with following objects: ccasIL… |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.4 | ColumnccasILSRxPattern | read-only | current | This object indicates the ABCD bit pattern of the signal being received on the DS0. |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.5 | ColumnccasILSMatchedRxPattern | read-only | current | This object indicates the previous matched ABCD bit pattern that was received on the DS0. |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.6 | ColumnccasILSMatchedTxPattern | read-only | current | This object indicates the current ABCD bit pattern being transmitted on the DS0. |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.7 | ColumnccasILSMinMakeTime | read-write | current | This object specifies the minimum time for which the received pattern (ccasILSRxPattern) must persist to be considered a valid state change or transition. If t… |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.8 | ColumnccasILSMaxMakeTime | read-write | current | This object specifies the maximum time for which the Rx pattern (ccasILSRxPattern) must persist to be considered a valid state change or transition. The value … |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.9 | ColumnccasILSMinBreakTime | read-write | current | This object specifies the minimum time for which the ABCD bit pattern being received on the line, and should go back to its original signal pattern after the m… |
| 1.3.6.1.4.1.9.9.314.1.3.1.1.10 | ColumnccasILSMaxBreakTime | read-write | current | This object specifies the maximum time for which the ABCD bit pattern being received on the line, and go back to its original signal pattern after the make pat… |
| 1.3.6.1.4.1.9.9.314.1.3.2 | TableccasIfExtOutgoingLineSignalTable | not-accessible | current | This table defines the parameters related to for the outgoing line signals pertaining to that CAS variant. |
| 1.3.6.1.4.1.9.9.314.1.3.2.1 | RowccasIfExtOutgoingLineSignalEntry | not-accessible | current | Each entry represents an incoming line signal definition for the CAS variant corresponding to the CAS Variant index. Entries in this table are implicitly creat… |
| 1.3.6.1.4.1.9.9.314.1.3.2.1.1 | ColumnccasOLSSignalNameIndex | not-accessible | current | This object specifies the Signal Name index for the various CAS Line signals. This object along with the ccasVariantIndex identify a unique entry in this table. |
| 1.3.6.1.4.1.9.9.314.1.3.2.1.2 | ColumnccasOLSCasSignalName | read-only | current | This object indicates outgoing CAS signal name. |
| 1.3.6.1.4.1.9.9.314.1.3.2.1.3 | ColumnccasOLSTxPattern | read-only | current | This object indicates the ABCD transmit bit pattern. |
| 1.3.6.1.4.1.9.9.314.1.3.2.1.4 | ColumnccasOLSMakeTime | read-write | current | This object specifies the time value for which the Tx Pattern being transmitted. |
| 1.3.6.1.4.1.9.9.314.1.3.2.1.5 | ColumnccasOLSBreakTime | read-write | current | This object specifies the time value for which the pattern being transmitted will switch to the original pattern before the Tx pattern was asserted on the line… |
| 1.3.6.1.4.1.9.9.314.1.3.3 | TableccasIfExtLineSignalTimerTable | not-accessible | current | This table defines all timers related to the CAS Line signals. |
| 1.3.6.1.4.1.9.9.314.1.3.3.1 | RowccasIfExtLineSignalTimerEntry | not-accessible | current | Each entry represents a CAS Line Signal Timer in media gateway. |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.1 | ColumnccasLSTIndex | not-accessible | current | An arbitrary index that uniquely identifies a entry in the ccasIfExtLineSignalTimerTable. The index 1 is reserved for the default entry. |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.2 | ColumnccasLSTIdleGuardTimer | read-create | current | This object specifies the maximum amount of time MG will wait for receipt of the idle signal on the line. For T1 interfaces idle signal corresponds to on-hook … |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.3 | ColumnccasLSTClearFwdTimer | read-create | current | This object specifies the value of the timer that the GW will start at the request of the controlling application such as MGC for receipt of the clear forward … |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.4 | ColumnccasLSTClearBwdTimer | read-create | current | This object specifies the value of the timer that the GW will start at the request of the controlling application such as MGC for receipt of the clear backward… |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.5 | ColumnccasLSTReleaseGuardTimer | read-create | current | This object specifies the delay between reception of the clear forward signal and the sending of the idle signal. Upon reception of the clear forward signal, G… |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.6 | ColumnccasLSTCASGlareTimer | read-create | current | This object specifies the maximum amount of time MG will wait for other end to back out when glare occurs on a DS0 line. Change in incoming off-hook signal to … |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.7 | ColumnccasLSTAnswerMeterDelayTimer | read-create | current | The object specifies the delay between generation of the answer signal and the generation of the meter signal. The GW will start this timer after having sent t… |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.8 | ColumnccasLSTCASDebounceTimer | read-create | current | This object specifies the amount of time for which the line signal should persist to be valid. The value of ccasLSTCASDebounceTimer must be less than or equal … |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.9 | ColumnccasLSTSeizeAckRspTimer | read-create | current | This object specifies the maximum amount of time MG will wait for reception of seize ack signal. Seize Ack signal is expected in response of seize signal. This… |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.10 | ColumnccasLSTDelayBetRegAnsAndLineAns | read-create | current | This object specifies the timer that will be started after register signaling completes successfully, within which the answer line signal should be received. T… |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.11 | ColumnccasLSTSeizeAckToDigitTimer | read-create | current | This object specifies the amount of time that the GW should wait for the reception address digits after sending seize ack signal. The value of 0 indicates the … |
| 1.3.6.1.4.1.9.9.314.1.3.3.1.12 | ColumnccasLSTRowStatus | read-create | current | This object is used for adding, deleting, and modifying the entries from the ccasIfExtLineSignalTimerTable. A default entry with index value 1 is created at in… |
| 1.3.6.1.4.1.9.9.314.1.4 | NodeccasIfExtConfigRegisterSignal | |||
| 1.3.6.1.4.1.9.9.314.1.4.1 | TableccasIfExtRegisterSignalTable | not-accessible | current | This table defines the signal to action definitions for the Register signals for R2 variant. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1 | RowccasIfExtRegisterSignalEntry | not-accessible | current | Entries are configured per country. When DS0 groups are associated with a CAS profile, it is also associated with one of these entries if the CAS variant is an… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.1 | ColumnccasRSIndex | not-accessible | current | This is an arbitrary index that uniquely identifies an entry in this table. This parameter is mandatory when creating an entry. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.2 | ColumnccasRSCountry | read-create | current | This object specifies the country where the meaning for the signal definition/action applies. This parameter is mandatory when creating an entry. When the R2 c… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.3 | ColumnccasRSSubRegion | read-create | current | This object is used to describe a variation within a particular country. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.4 | ColumnccasBwdRSNextDigitANI | read-create | current | This object specifies a backward signal requesting transmission of the next ANI digit (n + 1) after reception of digit n. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.5 | ColumnccasBwdRSNextDigitDNIS | read-create | current | This object specifies a backward signal requesting transmission of the next DNIS digit (n + 1) after reception of digit n. The default value is country specifi… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.6 | ColumnccasBwdRSPrevDigit | read-create | current | This object specifies a backward signal requesting transmission of the previous ANI or DNIS digit (n - 1) after reception of digit n. The default value is coun… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.7 | ColumnccasBwdRSXtoGroupBSignals | read-create | current | This object specifies a backward signal indicating that the incoming R2 register at the incoming end needs no additional address digit and is about to go over … |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.8 | ColumnccasBwdRSCongestion | read-create | current | This object specifies a backward signal indicating that: . Congestion of national links. . Congestion in selection stages of terminal international or national… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.9 | ColumnccasBwdRSCallingPartyCategory | read-create | current | This object specifies a backward signal requesting for a calling party category information or a Group II signal. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.10 | ColumnccasBwdRSAddrCompleteGroupA | read-create | current | This object specifies a backward signal indicating that the R2 register at the incoming end needs no additional digit, but will not send Group B signals. The c… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.11 | ColumnccasBwdRSPrevNminus2Digit | read-create | current | This object specifies a backward signal requesting the sending of the ANI or DNIS digit (n - 2) after reception of digit n. The default value is country specif… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.12 | ColumnccasBwdRSPrevNminus3Digit | read-create | current | This object specifies a backward signal requesting the sending of the ANI or DNIS digit (n - 3) after reception of digit n. The default value is country specif… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.13 | ColumnccasBwdRSCountryCode | read-create | current | This object specifies a backward signal requesting the country code indicator. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.14 | ColumnccasBwdRSLangDiscr | read-create | current | This object specifies a backward signal requesting the language digit or the discriminating digit. . Operator assistance: requesting a language digit. . Automa… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.15 | ColumnccasBwdRSNatureOfCircuit | read-create | current | This object specifies a backward signal requesting information regarding the nature of the circuits involved in the connection so far, i.e. satellite link or n… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.16 | ColumnccasBwdRSInfoEchoSuppressor | read-create | current | This object specifies a backward signal requesting information regarding the nature of echo suppressor being used in the connection. The default value is count… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.17 | ColumnccasBwdRSInternationalCongst | read-create | current | This object specifies a backward signal indicating: . Congestion on international links. . Congestion in selection stages at an international transit exchange … |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.18 | ColumnccasBwdRSXtoGroupC | read-create | current | This object specifies a backward signal requesting switch to reception of group C signals. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.19 | ColumnccasBwdRSRepeatLastDigit | read-create | current | This object specifies a backward signal requesting resending of the last digit just sent out. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.20 | ColumnccasBwdRSRepeatCalledDigit | read-create | current | This object specifies a backward signal requesting for out pulsing of the called digits or DNIS from beginning. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.21 | ColumnccasBwdRSPlaySITTone | read-create | current | This object specifies a backward signal indicating that SIT tone should be played towards the calling party. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.22 | ColumnccasBwdRSSubscriberLineBusy | read-create | current | This object specifies a backward signal indicating that the line or lines connecting the called subscriber to the exchange are busy or engaged. The default val… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.23 | ColumnccasBwdRSNetworkCongstInGroupB | read-create | current | This object specifies a backward signal indicating that congestion condition has occured after the changeover to Group B signals. The default value is country … |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.24 | ColumnccasBwdRSInvalidDialedNumber | read-create | current | This object specifies a backward signal indicating that the dialed or called number is invalid or not in use (e.g. an unused country code, an unused trunk code… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.25 | ColumnccasBwdRSSubLineFreeWithCharge | read-create | current | This object specifies a backward signal indicating that the called party's line is free and that the call has to be charged on answer. The default value is cou… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.26 | ColumnccasBwdRSSubLineFreeWithNoCharge | read-create | current | This object specifies a backward signal indicating that the called party line is free but is not to be charged on answer. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.27 | ColumnccasBwdRSSubLineOutOfOrder | read-create | current | This object specifies a backward signal indicating that the called party line is out of service or faulty. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.28 | ColumnccasBwdRSAnnouncement | read-create | current | This object specifies a backward signal indicating that an announcement follows this indication. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.29 | ColumnccasBwdRSXtoGrpASendNextDNIS | read-create | current | This object specifies a backward signal requesting the other exchange to switch to reception of group A and send the next DNIS digit. The default value is coun… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.30 | ColumnccasBwdRSXtoGrpASendDNISFrmBeg | read-create | current | This object specifies a backward signal requesting the other exchange to switch to reception of group A and send the DNIS digits from the beginning. The defaul… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.31 | ColumnccasBwdRSXtoGrpAResendLastDNIS | read-create | current | This object specifies a backward signal requesting the other exchange to switch to reception of group A and resend the last DNIS digit sent out. The default va… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.32 | ColumnccasBwdRSSSendCatSwGrpB | read-create | current | This object specifies a backward signal requesting the end receiving this signal to send the subscriber category information and switch to grp B from group C. … |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.33 | ColumnccasBwdRSSGrpCCong | read-create | current | This object specifies a backward signal indicating that congestion occurred in the network when in group C signaling state. The default value is country specif… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.34 | ColumnccasFwdRSANIDigitAvailable | read-create | current | This object specifies a forward signal indicating that ANI digits are available. This is used in country variants like India to indicate that the ANI digits ar… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.35 | ColumnccasFwdRSANIDigitNotAvailable | read-create | current | This object specifies a forward signal indicating that there are no ANI digits available for out pulsing. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.36 | ColumnccasFwdRSEndANICallingPartyNotRev | read-create | current | This object specifies a forward signal indicating that there are no more ANI digits to out pulse and the calling party can not be revealed to the called party.… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.37 | ColumnccasFwdRSEndANICallingPartyRev | read-create | current | This object specifies a forward signal indicating that there are no more ANI digits to out pulse and the calling party can be revealed to the called party. The… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.38 | ColumnccasFwdRSEndOfDNISDigit | read-create | current | This object specifies a forward signal indicating the end of DNIS digits. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.39 | ColumnccasFwdRSNoCategoryAvailble | read-create | current | This object specifies a forward signal indicating that there is no calling party category (information) available to be sent out. The default value is country … |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.40 | ColumnccasFwdRSCCEchoSuppressor | read-create | current | This object specifies a forward signal. When it is used as the first forward signal and it indicates that: . A country code will follow on an international lin… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.41 | ColumnccasFwdRSCCNoEchoSuppressor | read-create | current | This object specifies a forward signal. When it is used as the first forward signal and it indicates that: . A country code will follow on an international lin… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.42 | ColumnccasFwdRSCCInsertEchoSuppressor | read-create | current | This object specifies a forward signal. When it is used as the first forward signal and it indicates that: . A country code will follow on an international lin… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.43 | ColumnccasFwdRSIncHalfEchoRequired | read-create | current | This object specifies a forward signal indicating that: . The outgoing half echo suppressor has been inserted. . The incoming half echo suppressor is required.… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.44 | ColumnccasFwdRSTestCall | read-create | current | This object specifies a forward signal. When it is used as the first forward signal and indicates that the call is being originated by test equipment. The defa… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.45 | ColumnccasFwdRSSatelLinkIncluded | read-create | current | This object specifies a forward signal indicating that a satellite link is included in the connection. This signal is sent in response to backward signal reque… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.46 | ColumnccasFwdRSSatelLinkNotIncluded | read-create | current | This object specifies a forward signal indicating that no satellite link is included in the connection. This signal is sent in response to backward signal requ… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.47 | ColumnccasFwdRSDiscriminatorDigit | read-create | current | This object specifies a forward signal indicating the digit that separates or distinguishes different information blocks in the forward signals being generated… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.48 | ColumnccasFwdRSOtherLanguage | read-create | current | This object specifies a forward signal indicating that the language to be used for an operator assisted call. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.49 | ColumnccasFwdRSOtherLanguage1 | read-create | current | This object specifies a forward signal indicating that the language to be used for an operator assisted call. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.50 | ColumnccasFwdRSOtherLanguage2 | read-create | current | This object specifies a forward signal indicating that the language to be used for an operator assisted call. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.51 | ColumnccasFwdRSRequestNotAccepted | read-create | current | This object specifies a forward signal indicating that the receiving backward signal could not be processed or defined. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.52 | ColumnccasFwdRSSubWithoutPriorNational | read-create | current | This object specifies a forward signal indicating that the call is set up from a subscriber's line and is non-priority. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.53 | ColumnccasFwdRSSubPriorNational | read-create | current | This object specifies a forward signal indicating that the call is set up from a subscriber's line to which priority treatment of calls has been accorded. This… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.54 | ColumnccasFwdRSSubPriorInternational | read-create | current | This object specifies a forward signal indicating that the call is set up from a subscriber's line to which priority treatment of calls has been accorded. This… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.55 | ColumnccasFwdRSMaintenanceEquipment | read-create | current | This object specifies a forward signal indicating that the call comes from maintenance equipment. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.56 | ColumnccasFwdRSOperatorCall | read-create | current | This object specifies a forward signal indicating that the call is setup from an operator. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.57 | ColumnccasFwdRSDataTransNational | read-create | current | This object specifies a forward signal indicating that the call is being used for national data transmission. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.58 | ColumnccasFwdRSDataTransInternational | read-create | current | This object specifies a forward signal indicating that the call is being used for international data transmission. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.59 | ColumnccasFwdRSOperNoFwdTransFacility | read-create | current | This object specifies a forward signal indicating the call is being set up from a subscriber's line, operator's position or from maintenance equipment and no f… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.60 | ColumnccasFwdRSOperFwdTransFacility | read-create | current | This object specifies a forward signal indicating the call is set up from an operator's position with possibility of recourse to the forward transfer facility.… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.61 | ColumnccasFwdRSSubsrcWithMeter | read-create | current | This object specifies a forward signal indicating the subscribers have a meter. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.62 | ColumnccasFwdRSSubsrcWithIDD | read-create | current | This object specifies a forward signal indicating the subscribers have an International Direct Dial facility. The default value is country specific. |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.63 | ColumnccasRSInterpreFirstANIDigit | read-create | current | This object is used to interpret the meaning of the first ANI digit for both receiving and transmitting when sent and received. .firstANIDigit: First ANI digit… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.64 | ColumnccasRSGetValueFromValidIndex | read-create | current | This object specifies the entry index from which values for the objects not specified in the set operation will be copied over from. If both the country index … |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.65 | ColumnccasRSSeqInfCollect | read-create | current | This object determines the sequence in which information will be gathered by the incoming register. Only a set of predefined characters can be used in the octe… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.66 | ColumnccasRSSendFirstFwdSig | read-create | current | This object specifies the information element that will take precedence when being sent out as the first forward register signal for an outgoing call. This can… |
| 1.3.6.1.4.1.9.9.314.1.4.1.1.67 | ColumnccasRSRowStatus | read-create | current | This object is used for adding, modifying, and deleting the entries from the ccasRegisterSignalTable. A default entry with index value 1 is created at initiali… |
| 1.3.6.1.4.1.9.9.314.1.5 | NodeccasIfExtConfigTimer | |||
| 1.3.6.1.4.1.9.9.314.1.5.2 | TableccasIfExtRegSignalTimerTable | not-accessible | current | This table defines the timers related to the CAS register signals. |
| 1.3.6.1.4.1.9.9.314.1.5.2.1 | RowccasIfExtRegSignalTimerEntry | not-accessible | current | Each entry represents a CAS Register Signal Timer in media gateway. |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.1 | ColumnccasRSTIndex | not-accessible | current | An arbitrary index that uniquely identifies a entry in the ccasIfExtRegSignalTimerTable. The index of 1 is reserved for the default entry. |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.2 | ColumnccasRSTAnswerSigTimer | read-create | current | This object specifies the timer that is started after having sent out the last forward digit within which the backward register answer signal should be receive… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.3 | ColumnccasRSTCompelledFwdToneOnTimer | read-create | current | This object specifies the period for which the forward digit tone stays on, waiting for a reception of the backward signal in compelled signaling. This timer i… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.4 | ColumnccasRSTCompelledFwdToneOffTimer | read-create | current | This object specifies the period for which the forward signal digit is turned off in compelled signaling. This timer is started after the backward signal is re… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.5 | ColumnccasRSTCompelledBwdToneOnTimer | read-create | current | This object specifies the period for which the backward signal stays on waiting for the forward digit signal to go off in compelled signaling. This timer is st… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.6 | ColumnccasRSTOutFwdPulseOnTimer | read-create | current | This object specifies the timer is started after the forward digit tone is sent out. Tone is turned off after the timer expires. This object applies to outgoin… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.7 | ColumnccasRSTOutFwdPulseOffTimer | read-create | current | This object specifies the interval between two forward pulse tones. This object applies to outgoing R2 registers where the forward signals are sent as pulses f… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.8 | ColumnccasRSTIncFwdPulseOnTimer | read-create | current | This object specifies the period for which the forward digit pulse can be on. The timer is started after the forward digit signal is received, and stays on unt… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.9 | ColumnccasRSTBwdPulseOnTimer | read-create | current | This value specifies the period for which the backward pulse is on before it is turned off. This object applies to incoming R2 registers where the forward sign… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.10 | ColumnccasRSTIncomingRegSigDuration | read-create | current | This object specifies the duration within which the register signaling should complete for an incoming call. This timer is started as soon as the first forward… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.11 | ColumnccasRSTOutgoingRegSigDuration | read-create | current | This object specifies the duration within which the register signaling should complete for an outgoing call. This timer is started when the first forward regis… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.12 | ColumnccasRSTCalledPartyInterDigTimer | read-create | current | This object specifies the interdigit timer for the collection of called party number (DNIS) for R2 signaling when there is no digit map associated with the dig… |
| 1.3.6.1.4.1.9.9.314.1.5.2.1.13 | ColumnccasRSTRowStatus | read-create | current | This object is used for adding, deleting and modifying the entries from the ccasIfExtRegSignalTimerTable. A default entry with index value 1 is created at init… |
| 1.3.6.1.4.1.9.9.314.1.6 | NodeccasIfExtGeneralConfig | |||
| 1.3.6.1.4.1.9.9.314.1.6.1 | TableccasIfExtGeneralConfigTable | not-accessible | current | This table defines the general parameters related to CAS variant. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1 | RowccasIfExtGeneralConfigEntry | not-accessible | current | An entry represents a general attribute for CAS variant in media gateway. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.1 | ColumnccasGCnfIndex | not-accessible | current | An arbitrary index that uniquely identifies a entry in the ccasIfExtGeneralConfigTable. The index of 1 is reserved for the default entry. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.2 | ColumnccasGCnfGlarePolicy | read-create | current | This object specifies a glare policy. It is used only if CAS DS0 directionality of the endpoint is bidirectional, and is applicable for non R2 variants. . rptS… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.3 | ColumnccasGCnfParmSource | read-create | current | This object indicates whether GW should read the CAS related timer parameters from the CAS Variant file downloaded for that endpoint or to read from the MIB. T… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.4 | ColumnccasGCnfRegSigMode | read-create | current | This object specifies the register signaling mode for a R2 registers. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.5 | ColumnccasGCnfLineSigType | read-create | current | This object specifies the line signaling type that will be used for the R2 line signaling. . digital (1): The digital line signaling is typically used for PCM … |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.6 | ColumnccasGCnfRingBackType | read-create | current | This object specifies the ring back signal type of FGD protocol. . wink (1): A pulse which is a timed transition from on hook to off hook and back to on hook. … |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.7 | ColumnccasGCnfIncCallHiFreqPower | read-create | current | This object specifies the power of the high frequency signal component for incoming call. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.8 | ColumnccasGCnfIncCallLoFreqPower | read-create | current | This object specifies the power of the low frequency signal component for incoming call. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.9 | ColumnccasGCnfIncCallNegTwist | read-create | current | This object specifies a negative power twist when the power level of the low frequency component is set to relatively higher than the high frequency component … |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.10 | ColumnccasGCnfIncCallPosTwist | read-create | current | This object specifies a positive power twist when the power level of the high frequency component is set to relatively higher than the low frequency component … |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.11 | ColumnccasGCnfIncCallBreakThreshold | read-create | current | This object specifies a power level which is used for detection of on hook to off hook transition for incoming call. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.12 | ColumnccasGCnfOutCallLoFreqPower | read-create | current | This object specifies the power level of the low frequency component for outgoing call. The power level of the high frequency component of outgoing call is rel… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.13 | ColumnccasGCnfOutCallPowerTwist | read-create | current | This object specifies the relative power level of the high frequency component for outgoing call. When this object is set to 0, the power level of both frequen… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.14 | ColumnccasGCnfOutCadenceOntime | read-create | current | This object specifies the duration during which the digit tone is generated for outgoing call. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.15 | ColumnccasGCnfOutCadenceOfftime | read-create | current | This object specifies the silence between digit tones for outgoing call. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.16 | ColumnccasGCnfCountryCode | read-create | current | This object specifies the country code digits. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.17 | ColumnccasGCnfEchoCancellation | read-create | current | This object specifies the echo cancellation mode, and it is applicable to an outgoing R2 register. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.18 | ColumnccasGCnfSubscriberCategory | read-create | current | This object specifies the subscriber category types: . (1) subscriber without priority . (2) subscriber with priority . (3) maintenance equipment . (4) operato… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.19 | ColumnccasGCnfNatureOfCircuit | read-create | current | This object specifies if there is any satellite link in the path: . (1) Satellite link is not included. . (2) Satellite link is included. |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.20 | ColumnccasGCnfCompelledSignalingType | read-create | current | This object specifies the Compelled Signaling type: . enbloc (1): The called number is forwarded in a block. . overlap (2): The called numder is forwarded one … |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.21 | ColumnccasGCnfTxDigitOrder | read-create | current | This object specifies the transmit digit order in which ANI and DNIs will be dialled out when the controlling application gives both the the calling party numb… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.22 | ColumnccasGCnfDigitDetectMode | read-create | current | This objects specifies the digit detect mode that the GW should be opened with for reception of digits. . dtmf (1): Dual tone multifrequency . mf (2): Multifre… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.23 | ColumnccasGCnfMeteringRepIntThresh | read-create | current | This object specifies the duration between two consecutive metering pulses, if it changes more than value specified in this parameter then an event will be tri… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.24 | ColumnccasGCnfStartTimer | read-create | current | This object specifies the amount of time that the GW must wait for receiving digits after generating the seize ACK or start dial indication for an incoming cal… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.25 | ColumnccasGCnfLongTimer | read-create | current | This object specifies the period between receiving digits. The timer is not started until the first digit is received. The GW starts this timer during digit co… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.26 | ColumnccasGCnfShortTimer | read-create | current | This object specifies the period between receiving digits. The GW starts this timer during digit collection when the digit string that it has collected matches… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.27 | ColumnccasGCnfLongDurationTimer | read-create | current | This object specifies long duration event when placed in front of a digit. It indicates that that position is satisfied only if the duration of the event excee… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.28 | ColumnccasGCnfMGCTimer | read-create | current | This object specifies the timer in the GW waiting for the MGC to provide the rest of the information for CAS signaling. During overlap CAS signaling, for an ou… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.29 | ColumnccasGCnfDigitType | read-create | current | This object specifies the digit type to pulsed from the GW such as: .dtmf - Dual tone multifrequency. .mf - Multifrequency. .dp - Dial pulse. This parameter ca… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.30 | ColumnccasGCnfEndPointDirectional | read-create | current | This object specifies the direction in which CAS calls will be accepted on this endpoint. .bidirectional - Accepts both incoming and outgoing calls. .incoming … |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.31 | ColumnccasGCnfPulseReceiveTimeout | read-create | current | This object specifies the time that the MG should wait for the receipt of pulse (on hook pulse or off hook pulse). The value of 0 indicates the timer will not … |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.32 | ColumnccasGCnfInitialDelay | read-create | current | This object specifies the initial delay that must be applied on an outgoing trunk before the digits are pulse out. The value of 0 indicates the timer, ccasGCnf… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.33 | ColumnccasGCnfMaxNumCallParty | read-create | current | This object specifies the maximum number of calling party digits to collect for reporting to the MGC. The MGC can overridden this value, and a value of 0 indic… |
| 1.3.6.1.4.1.9.9.314.1.6.1.1.34 | ColumnccasGCnfRowStatus | read-create | current | This object is used for adding, modifying, deleting the entries from the ccasExtIfGeneralConfigTable. A default entry with index value 1 is created at initiali… |
| 1.3.6.1.4.1.9.9.314.2 | NodeciscoCasIfExtMIBConformance | |||
| 1.3.6.1.4.1.9.9.314.2.1 | NodeccasIfExtMIBCompliances | |||
| 1.3.6.1.4.1.9.9.314.2.1.1 | ComplianceccasIfExtMIBCompliance | deprecated | The compliance statement for the SNMP entities which implement ciscoCasIfExtMIB. This has been replaced by ccasIfExtMIBComplianceRev1. | |
| 1.3.6.1.4.1.9.9.314.2.1.2 | ComplianceccasIfExtMIBComplianceRev1 | deprecated | The compliance statement for the SNMP entities which implement ciscoCasIfExtMIB. This has been replaced by ccasIfExtMIBComplianceRev2. | |
| 1.3.6.1.4.1.9.9.314.2.1.3 | ComplianceccasIfExtMIBComplianceRev2 | deprecated | The compliance statement for the SNMP entities which implement ciscoCasIfExtMIB. This has been replaced by ccasIfExtMIBComplianceRev3. | |
| 1.3.6.1.4.1.9.9.314.2.1.4 | ComplianceccasIfExtMIBComplianceRev3 | current | The compliance statement for the SNMP entities which implement ciscoCasIfExtMIB. | |
| 1.3.6.1.4.1.9.9.314.2.2 | NodeccasIfExtMIBGroups | |||
| 1.3.6.1.4.1.9.9.314.2.2.1 | GroupccasIfExtVoiceCfgGroup | deprecated | This group contains objects that apply to the DS0 group of DS1 configuration in media gateways. | |
| 1.3.6.1.4.1.9.9.314.2.2.2 | GroupccasIfExtBulkGroup | current | This group contains objects that apply to the bulk configuration for the DS0 group associated voice specific parameters in media gateway. | |
| 1.3.6.1.4.1.9.9.314.2.2.3 | GroupccasIfExtVoiceCfgGroupRev1 | current | This group contains objects that apply to the DS0 group of DS1 configuration in media gateways. | |
| 1.3.6.1.4.1.9.9.314.2.2.4 | GroupccasIfExtVoiceCfgCasGroup | current | This group contains objects that apply to the DS0 group of DS1 configuration for CAS. | |
| 1.3.6.1.4.1.9.9.314.2.2.5 | GroupccasIfExtProfileGroup | current | A collection of objects providing information applicable to CAS Profile. | |
| 1.3.6.1.4.1.9.9.314.2.2.6 | GroupccasIfExtConfigLineSignalGroup | current | A collection of objects providing information applicable to Line Signal. | |
| 1.3.6.1.4.1.9.9.314.2.2.7 | GroupccasIfExtConfigRegisterSignalGroup | current | A collection of objects providing information applicable to Register Signal. | |
| 1.3.6.1.4.1.9.9.314.2.2.8 | GroupccasIfExtConfigTimerGroup | current | A collection of objects providing information applicable to timer. | |
| 1.3.6.1.4.1.9.9.314.2.2.9 | GroupccasIfExtGeneralConfigGroup | current | A collection of objects providing information applicable to general CAS configuration. | |
| 1.3.6.1.4.1.9.9.314.2.2.10 | GroupccasIfExtVoiceCfgGroupSup1 | current | This group contains supplemental objects that apply to the voice configuration in media gateways. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CASBackwardSignal | INTEGER { notApplicable (1), a1 (2), a2 (3), a3 (4), a4 (5), a5 (6), a6 (7), a7 (8), a8 (9), a9 (10), a10 (11), a11 (12), a12 (13), a13 (14), a14 (15), a15 (16), b1 (17), b2 (18), b3 (19), b4 (20), b5 (21), b6 (22), b7 (23), b8 (24), b9 (25), b10 (26), b11 (27), b12 (28), b13 (29), b14 (30), b15 (31), c1 (32), c2 (33), c3 (34), c4 (35), c5 (36), c6 (37), c7 (38), c8 (39), c9 (40), c10 (41), c11 (42), c12 (43), c13 (44), c14 (45), c15 (46) } | current | This textual convention defines all possible Group A, B and C Backward Signal in Signaling System R2. The group-A tones are generally used to query the call setup related information from the outgoing register. The grou… |
| CASCountryCode | INTEGER { itu (1), argentina (2), australia (3), bolivia (4), brazil (5), bulgaria (6), china (7), colombia (8), costaRica (9), croatia (10), eastEurope (11), ecuadorIT (12), ecuadorLME (13), greece (14), guatemala (15), hongKong (16), india (17), indonesia (18), israel (19), korea (20), laos (21), malaysia (22), malta (23), mongolia (24), newZealand (25), paraguay (26), peru (27), philippines (28), saudiArabia (29), singapore (30), southAfrica (31), telemex (32), telnor (33), thailand (34), uruguay (35), venezuela (36), vietnam (37), bemilcom (38) } | current | This textual convention defines all possible countries supported to CAS. |
| CASForwardSignal | INTEGER { notApplicable (1), i1 (2), i2 (3), i3 (4), i4 (5), i5 (6), i6 (7), i7 (8), i8 (9), i9 (10), i10 (11), i11 (12), i12 (13), i13 (14), i14 (15), i15 (16), ii1 (17), ii2 (18), ii3 (19), ii4 (20), ii5 (21), ii6 (22), ii7 (23), ii8 (24), ii9 (25), ii10 (26), ii11 (27), ii12 (28), ii13 (29), ii14 (30), ii15 (31), iiI1 (32), iiI2 (33), iii3 (34), iii4 (35), iii5 (36), iii6 (37), iii7 (38), iii8 (39), iii9 (40), iii10 (41), iii11 (42), iii12 (43), iii13 (44), iii14 (45), iii15 (46) } | current | This textual convention defines all possible Group I, II, and III Forward Signals in Signaling System R2. The Forward Group I signals represent the called numbers, calling party number and equipment requirements for the… |
| CASLineSignal | OCTET STRING (SIZE(1)) | current | This textual convention defines line signals indicating the ABCD bits of CAS signaling, which represent the states of lines. Each of A, B, C or D represents by two bit value : b(bit)1 | b0 | value 0 | 0 | 0 0 | 1 | 1 1 … |
| CASRegisterSignal | INTEGER { compelled (1), noncompelled (2), semicompelled (3) } | current | This textual convention defines Register Signaling. Signals (tones) sent from the calling party to the called party are called forward register signals. Signals (tones) sent from the called party to the calling party ar… |