CISCO-IETF-MPLS-TE-P2MP-STD-MIB
72 objects
This MIB module contains managed object definitions for Point-to-Multipoint (P2MP) MPLS Traffic Engineering (TE) defined in: 1. Signaling Requirements for Point-to-Multipoint Traffic-Engineered MPLS Label Switched Paths (LSPs), S. Yasukawa, RFC 4461, April 2006. 2. Extensions to Resource Reservation Protocol - Traffic Engineering (RSVP-TE) for Point-to-Multipoint TE Label Switched Paths (LSPs), Aggarwal, R., Papadimitriou, D., and Yasukawa, S., RFC 4875, May 2007.
Imported Objects
| CISCO-SMI | ciscoExperiment |
| DIFFSERV-MIB | IndexInteger IndexIntegerNextFree |
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| MPLS-LSR-STD-MIB | MplsIndexType |
| MPLS-TC-STD-MIB | MplsLabel MplsPathIndexOrZero |
| MPLS-TE-STD-MIB | mplsTunnelEgressLSRId mplsTunnelIndex mplsTunnelIngressLSRId mplsTunnelInstance |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.142 | IdentitycmplsTeP2mpStdMIB | This MIB module contains managed object definitions for Point-to-Multipoint (P2MP) MPLS Traffic Engineering (TE) defined in: 1. Signaling Requirements for Poin… | ||
| 1.3.6.1.4.1.9.10.142.0 | NodecmplsTeP2mpNotifications | |||
| 1.3.6.1.4.1.9.10.142.0.1 | NotificationcmplsTeP2mpTunnelDestUp | current | This notification is generated when a cmplsTeP2mpTunnelDestOperStatus object for one of the destinations of one of the configured tunnels is about to leave the… | |
| 1.3.6.1.4.1.9.10.142.0.2 | NotificationcmplsTeP2mpTunnelDestDown | current | This notification is generated when a cmplsTeP2mpTunnelDestOperStatus object for one of the destinations of one of the configured tunnels is about to enter the… | |
| 1.3.6.1.4.1.9.10.142.1 | NodecmplsTeP2mpScalars | |||
| 1.3.6.1.4.1.9.10.142.1.1 | ScalarcmplsTeP2mpTunnelConfigured | read-only | current | The number of P2MP tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus in MPLS-TE-STD-MIB is active(1). |
| 1.3.6.1.4.1.9.10.142.1.2 | ScalarcmplsTeP2mpTunnelActive | read-only | current | The number of P2MP tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus in MPLS-TE-STD-MIB is up(1). |
| 1.3.6.1.4.1.9.10.142.1.3 | ScalarcmplsTeP2mpTunnelTotalMaxHops | read-only | current | The maximum number of hops that can be specified for an entire P2MP tunnel on this device. This object should be used in conjunction with mplsTunnelMaxHops in … |
| 1.3.6.1.4.1.9.10.142.2 | NodecmplsTeP2mpObjects | |||
| 1.3.6.1.4.1.9.10.142.2.1 | TablecmplsTeP2mpTunnelTable | not-accessible | current | The cmplsTeP2mpTunnelTable allows new P2MP MPLS tunnels to be created between an LSR and one or more remote end-points, and existing P2MP tunnels to be reconfi… |
| 1.3.6.1.4.1.9.10.142.2.1.1 | RowcmplsTeP2mpTunnelEntry | not-accessible | current | An entry in this table represents a P2MP MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling… |
| 1.3.6.1.4.1.9.10.142.2.1.1.2 | ColumncmplsTeP2mpTunnelP2mpIntegrity | read-create | current | Denotes whether or not P2MP Integrity is required for this tunnel. If P2MP integrity is operational on a P2MP tunnel then the failure of the path to any of the… |
| 1.3.6.1.4.1.9.10.142.2.1.1.3 | ColumncmplsTeP2mpTunnelBranchRole | read-create | current | This value supplements the value in the object mplsTunnelRole in MPLS-TE-STD-MIB that indicates the role of this LSR in the tunnel represented by this entry in… |
| 1.3.6.1.4.1.9.10.142.2.1.1.4 | ColumncmplsTeP2mpTunnelP2mpXcIndex | read-only | current | This object contains the value of mplsXCIndex, the primary index of the mplsXCTable for all cross-connect entries for this P2MP LSP. If no XC entries have been… |
| 1.3.6.1.4.1.9.10.142.2.1.1.5 | ColumncmplsTeP2mpTunnelRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.4.1.9.10.142.2.1.1.6 | ColumncmplsTeP2mpTunnelStorageType | read-create | current | The storage type for this tunnel entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.4.1.9.10.142.2.2 | ScalarcmplsTeP2mpTunnelSubGroupIDNext | read-only | current | This object contains an unused value for cmplsTeP2mpTunnelDestSubGroupID, or a zero to indicate that none exists. Negative values are not allowed, as they do n… |
| 1.3.6.1.4.1.9.10.142.2.3 | TablecmplsTeP2mpTunnelDestTable | not-accessible | current | The cmplsTeP2mpTunnelDestTable allows new destinations of P2MP MPLS tunnels to be added to and removed from P2MP tunnels. |
| 1.3.6.1.4.1.9.10.142.2.3.1 | RowcmplsTeP2mpTunnelDestEntry | not-accessible | current | An entry in this table represents a destination of a P2MP MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by … |
| 1.3.6.1.4.1.9.10.142.2.3.1.1 | ColumncmplsTeP2mpTunnelDestSrcSubGroupOriginType | not-accessible | current | This object identifies the type of address carried in cmplsTeP2mpTunnelDestSrcSubGroupOrigin. Since the object cmplsTeP2mpTunnelDestSrcSubGroupOrigin must conf… |
| 1.3.6.1.4.1.9.10.142.2.3.1.2 | ColumncmplsTeP2mpTunnelDestSrcSubGroupOrigin | not-accessible | current | The TE Router ID (reachable and stable IP address) of the originator of the P2MP sub-group as received on a Path message by a transit or egress LSR. This objec… |
| 1.3.6.1.4.1.9.10.142.2.3.1.3 | ColumncmplsTeP2mpTunnelDestSrcSubGroupID | not-accessible | current | The unique identifier assigned by the sub-group originator for this sub-group of this P2MP tunnel as received on a Path message by a transit or egress LSR. The… |
| 1.3.6.1.4.1.9.10.142.2.3.1.4 | ColumncmplsTeP2mpTunnelDestSubGroupOriginType | not-accessible | current | This object identifies the type of address carried in cmplsTeP2mpTunnelDestSubGroupOrigin. This object must return either ipv4(1) or ipv6(2) in keeping with th… |
| 1.3.6.1.4.1.9.10.142.2.3.1.5 | ColumncmplsTeP2mpTunnelDestSubGroupOrigin | not-accessible | current | The TE Router ID (reachable and stable IP address) of the originator of the P2MP sub-group. In many cases, this will be the ingress LSR of the P2MP tunnel and … |
| 1.3.6.1.4.1.9.10.142.2.3.1.6 | ColumncmplsTeP2mpTunnelDestSubGroupID | not-accessible | current | The unique identifier assigned by the sub-group originator for this sub-group of this P2MP tunnel. An appropriate value for this object during row creation whe… |
| 1.3.6.1.4.1.9.10.142.2.3.1.7 | ColumncmplsTeP2mpTunnelDestDestinationType | not-accessible | current | This object identifies the type of address carried in cmplsTeP2mpTunnelDestDestination. This object forms part of the index of this table and can, therefore, n… |
| 1.3.6.1.4.1.9.10.142.2.3.1.8 | ColumncmplsTeP2mpTunnelDestDestination | not-accessible | current | A single destination of this P2MP tunnel. That is, a routable TE address of a leaf. This will often be the TE Router ID of the leaf, but can be any interface a… |
| 1.3.6.1.4.1.9.10.142.2.3.1.9 | ColumncmplsTeP2mpTunnelDestBranchOutSegment | read-only | current | This object identifies the outgoing branch from this LSR towards the destination represented by this table entry. It must be a unique identifier within the sco… |
| 1.3.6.1.4.1.9.10.142.2.3.1.10 | ColumncmplsTeP2mpTunnelDestHopTableIndex | read-create | current | Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this destination of the P2MP tunnel. This object represents the configured r… |
| 1.3.6.1.4.1.9.10.142.2.3.1.11 | ColumncmplsTeP2mpTunnelDestPathInUse | read-create | current | This value denotes the configured path that was chosen as the explicit path to this destination of this P2MP tunnel. This value reflects the secondary index in… |
| 1.3.6.1.4.1.9.10.142.2.3.1.12 | ColumncmplsTeP2mpTunnelDestCHopTableIndex | read-only | current | Index into the mplsTunnelCHopTable that identifies the explicit path for this destination of the P2MP tunnel. This path is based on the chosen configured path … |
| 1.3.6.1.4.1.9.10.142.2.3.1.13 | ColumncmplsTeP2mpTunnelDestARHopTableIndex | read-only | current | Index into the mplsTunnelARHopTable that identifies the actual hops traversed to this destination of the P2MP tunnel. This is automatically updated by the agen… |
| 1.3.6.1.4.1.9.10.142.2.3.1.14 | ColumncmplsTeP2mpTunnelDestTotalUpTime | read-only | current | This value represents the aggregate up time for all instances of this tunnel to this destination, if this information is available. If this information is not … |
| 1.3.6.1.4.1.9.10.142.2.3.1.15 | ColumncmplsTeP2mpTunnelDestInstanceUpTime | read-only | current | This value identifies the total time that the currently active tunnel instance to this destination has had its operational status (mplsTeP2mpTunnelDestOperStat… |
| 1.3.6.1.4.1.9.10.142.2.3.1.16 | ColumncmplsTeP2mpTunnelDestPathChanges | read-only | current | This object counts the number of times the actual path for this destination of this P2MP tunnel instance has changed. This object should be read in conjunction… |
| 1.3.6.1.4.1.9.10.142.2.3.1.17 | ColumncmplsTeP2mpTunnelDestLastPathChange | read-only | current | Specifies the time since the last change to the actual path for this destination of this P2MP tunnel instance. |
| 1.3.6.1.4.1.9.10.142.2.3.1.18 | ColumncmplsTeP2mpTunnelDestCreationTime | read-only | current | Specifies the value of sysUpTime when the first instance of this tunnel came into existence for this destination. That is, when the value of cmplsTeP2mpTunnelD… |
| 1.3.6.1.4.1.9.10.142.2.3.1.19 | ColumncmplsTeP2mpTunnelDestStateTransitions | read-only | current | This object counts the number of times the status (mplsTeP2mpTunnelDestOperStatus) of this tunnel instance to this destination has changed. This object should … |
| 1.3.6.1.4.1.9.10.142.2.3.1.20 | ColumncmplsTeP2mpTunnelDestDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this row's Counter32 objects experienced a discontinuity. If no such discontinui… |
| 1.3.6.1.4.1.9.10.142.2.3.1.21 | ColumncmplsTeP2mpTunnelDestAdminStatus | read-create | current | Indicates the desired operational status of this destination of this P2MP tunnel. |
| 1.3.6.1.4.1.9.10.142.2.3.1.22 | ColumncmplsTeP2mpTunnelDestOperStatus | read-only | current | Indicates the actual operational status of this destination of this P2MP tunnel. This object may be compared to mplsTunnelOperStatus that includes two other va… |
| 1.3.6.1.4.1.9.10.142.2.3.1.23 | ColumncmplsTeP2mpTunnelDestRowStatus | read-create | current | This object is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modifie… |
| 1.3.6.1.4.1.9.10.142.2.3.1.24 | ColumncmplsTeP2mpTunnelDestStorageType | read-create | current | The storage type for this table entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.4.1.9.10.142.2.4 | TablecmplsTeP2mpTunnelBranchPerfTable | not-accessible | current | This table provides per-tunnel branch MPLS performance information. This table is not valid for switching types other than packet. |
| 1.3.6.1.4.1.9.10.142.2.4.1 | RowcmplsTeP2mpTunnelBranchPerfEntry | not-accessible | current | An entry in this table is created by the LSR for each downstream branch (out-segment) from this LSR for this P2MP tunnel. More than one destination as represen… |
| 1.3.6.1.4.1.9.10.142.2.4.1.1 | ColumncmplsTeP2mpTunnelBranchPerfBranch | not-accessible | current | This object identifies an outgoing branch from this LSR for this tunnel. Its value is unique within the context of the tunnel. If MPLS-LSR-STD-MIB is implement… |
| 1.3.6.1.4.1.9.10.142.2.4.1.2 | ColumncmplsTeP2mpTunnelBranchPerfPackets | read-only | current | Number of packets forwarded by the tunnel onto this branch. This object should represents the 32-bit value of the least significant part of the 64-bit value if… |
| 1.3.6.1.4.1.9.10.142.2.4.1.3 | ColumncmplsTeP2mpTunnelBranchPerfHCPackets | read-only | current | High capacity counter for number of packets forwarded by the tunnel onto this branch. This object should be read in conjunction with cmplsTeP2mpTunnelBranchDis… |
| 1.3.6.1.4.1.9.10.142.2.4.1.4 | ColumncmplsTeP2mpTunnelBranchPerfErrors | read-only | current | Number of packets dropped because of errors or for other reasons, that were supposed to be forwarded onto this branch for this tunnel. This object should be re… |
| 1.3.6.1.4.1.9.10.142.2.4.1.5 | ColumncmplsTeP2mpTunnelBranchPerfBytes | read-only | current | Number of bytes forwarded by the tunnel onto this branch. This object should represents the 32-bit value of the least significant part of the 64-bit value if b… |
| 1.3.6.1.4.1.9.10.142.2.4.1.6 | ColumncmplsTeP2mpTunnelBranchPerfHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the tunnel onto this branch. This object should be read in conjunction with cmplsTeP2mpTunnelBranchDisco… |
| 1.3.6.1.4.1.9.10.142.2.4.1.7 | ColumncmplsTeP2mpTunnelBranchDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this row's Counter32 or Counter64 objects experienced a discontinuity. If no suc… |
| 1.3.6.1.4.1.9.10.142.2.4.1.8 | ColumncmplsTeP2mpTunnelBranchLocalLabel | read-only | current | The local MPLS label for this branch. This object is not part of the original draft |
| 1.3.6.1.4.1.9.10.142.2.4.1.9 | ColumncmplsTeP2mpTunnelBranchOutIfIndex | read-only | current | This is the index of outgoing TE link physical I/F for the P2MP egress tunnel branch. It is non-zero when the P2MP tunnel's outgoing branch has been signaled. … |
| 1.3.6.1.4.1.9.10.142.2.4.1.10 | ColumncmplsTeP2mpTunnelBranchOutLabel | read-only | current | The outgoing MPLS label for this branch. |
| 1.3.6.1.4.1.9.10.142.2.4.1.11 | ColumncmplsTeP2mpTunnelBranchSignalArea | read-only | current | This is the IGP area instance name/number that the outgoing tunnel branch is signaled in. TE can allow (currently not supported for P2MP tunnels but could be i… |
| 1.3.6.1.4.1.9.10.142.2.4.1.12 | ColumncmplsTeP2mpTunnelBranchInIfIndex | read-only | current | This is the index of incoming TE link physical I/F for the P2MP ingress tunnel branch. It is non-zero when the P2MP tunnel's incoming branch has been signaled … |
| 1.3.6.1.4.1.9.10.142.2.5 | ScalarcmplsTeP2mpTunnelNotificationEnable | read-write | current | If this object is true(1), then it enables the generation of cmplsTeP2mpTunnelDestUp and cmplsTeP2mpTunnelDestDown notifications. Otherwise these notifications… |
| 1.3.6.1.4.1.9.10.142.3 | NodecmplsTeP2mpConformance | |||
| 1.3.6.1.4.1.9.10.142.3.1 | NodecmplsTeP2mpGroups | |||
| 1.3.6.1.4.1.9.10.142.3.1.1 | GroupcmplsTeP2mpGeneralGroup | current | Collection of objects needed for MPLS P2MP. | |
| 1.3.6.1.4.1.9.10.142.3.1.2 | GroupcmplsTeP2mpNotifGroup | current | Notifications implemented in this module. | |
| 1.3.6.1.4.1.9.10.142.3.1.3 | GroupcmplsTeP2mpScalarGroup | current | Scalar objects needed to implement P2MP MPLS tunnels. | |
| 1.3.6.1.4.1.9.10.142.3.1.4 | GroupcmplsTeP2mpGeneralGroupSup1 | current | Addition to collection of objects needed for MPLS P2MP. | |
| 1.3.6.1.4.1.9.10.142.3.1.5 | GroupcmplsTeP2mpGeneralGroupSup2 | current | Addition to collection of objects needed for MPLS P2MP. | |
| 1.3.6.1.4.1.9.10.142.3.2 | NodecmplsTeP2mpCompliances | |||
| 1.3.6.1.4.1.9.10.142.3.2.1 | CompliancecmplsTeP2mpModuleFullCompliance | deprecated | Compliance statement for agents that provide full support for MPLS-TE-P2MP-STD-MIB. Such devices can be monitored and also be configured using this MIB module.… | |
| 1.3.6.1.4.1.9.10.142.3.2.2 | CompliancecmplsTeP2mpModuleReadOnlyCompliance | read-only | deprecated | Compliance statement for agents that provide read-only support for MPLS-TE-P2MP-STD-MIB. Such devices can only be monitored using this MIB module. The Module i… |
| 1.3.6.1.4.1.9.10.142.3.2.3 | CompliancecmplsTeP2mpModuleFullComplianceRev1 | deprecated | Compliance statement for agents that provide full support for MPLS-TE-P2MP-STD-MIB. Such devices can be monitored and also be configured using this MIB module.… | |
| 1.3.6.1.4.1.9.10.142.3.2.4 | CompliancecmplsTeP2mpModuleReadOnlyComplianceRev1 | read-only | deprecated | Compliance statement for agents that provide read-only support for MPLS-TE-P2MP-STD-MIB. Such devices can only be monitored using this MIB module. The Module i… |
| 1.3.6.1.4.1.9.10.142.3.2.5 | CompliancecmplsTeP2mpModuleFullComplianceRev2 | current | Compliance statement for agents that provide full support for MPLS-TE-P2MP-STD-MIB. Such devices can be monitored and also be configured using this MIB module.… | |
| 1.3.6.1.4.1.9.10.142.3.2.6 | CompliancecmplsTeP2mpModuleReadOnlyComplianceRev2 | read-only | current | Compliance statement for agents that provide read-only support for MPLS-TE-P2MP-STD-MIB. Such devices can only be monitored using this MIB module. The Module i… |