JNX-MPLS-TE-P2MP-STD-MIB
61 objects
Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document. The initial version of this MIB module was published in RFC XXXX. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for Point-to-Multipoint (P2MP) MPLS Traffic Engineering (TE) defined in: 1. Signaling Requirements for Point-to-Multipoint Traffic-Engineered MPLS Label Switched Paths (LSPs), S. Yasukawa, RFC 4461, April 2006. 2. Extensions to Resource Reservation Protocol - Traffic Engineering (RSVP-TE) for Point-to-Multipoint TE Label Switched Paths (LSPs), Aggarwal, R., Papadimitriou, D., and Yasukawa, S., RFC 4875, May 2007.
Imported Objects
| DIFFSERV-MIB | -- RFC 3812 IndexInteger IndexIntegerNextFree |
| INET-ADDRESS-MIB | -- RFC 3289 InetAddress InetAddressType |
| MPLS-LSR-STD-MIB | -- RFC 3811 MplsIndexType |
| MPLS-TC-STD-MIB | -- RFC 2579 mplsStdMIB MplsPathIndexOrZero |
| MPLS-TE-STD-MIB | -- RFC 3813 mplsTunnelIndex mplsTunnelEgressLSRId mplsTunnelIngressLSRId mplsTunnelInstance |
| SNMPv2-CONF | -- RFC 2578 MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | -- RFC 2580 TruthValue RowStatus StorageType TimeStamp |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2636.5.7.1 | IdentityjnxMplsTeP2mpStdMIB | Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's … | ||
| 1.3.6.1.4.1.2636.5.7.1.0 | NodejnxMplsTeP2mpNotifications | |||
| 1.3.6.1.4.1.2636.5.7.1.0.1 | NotificationjnxMplsTeP2mpTunnelDestUp | current | This notification is generated when a mplsTeP2mpTunnelDestOperStatus object for one of the destinations of one of the configured tunnels is about to leave the … | |
| 1.3.6.1.4.1.2636.5.7.1.0.2 | NotificationjnxMplsTeP2mpTunnelDestDown | current | This notification is generated when a mplsTeP2mpTunnelDestOperStatus object for one of the destinations of one of the configured tunnels is about to enter the … | |
| 1.3.6.1.4.1.2636.5.7.1.1 | NodejnxMplsTeP2mpScalars | |||
| 1.3.6.1.4.1.2636.5.7.1.1.1 | ScalarjnxMplsTeP2mpTunnelConfigured | read-only | current | The number of P2MP tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus in MPLS-TE-STD-MIB is active(1). |
| 1.3.6.1.4.1.2636.5.7.1.1.2 | ScalarjnxMplsTeP2mpTunnelActive | read-only | current | The number of P2MP tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus in MPLS-TE-STD-MIB is up(1). |
| 1.3.6.1.4.1.2636.5.7.1.1.3 | ScalarjnxMplsTeP2mpTunnelTotalMaxHops | read-only | current | The maximum number of hops that can be specified for an entire P2MP tunnel on this device. This object should be used in conjunction with mplsTunnelMaxHops in … |
| 1.3.6.1.4.1.2636.5.7.1.2 | NodejnxMplsTeP2mpObjects | |||
| 1.3.6.1.4.1.2636.5.7.1.2.1 | TablejnxMplsTeP2mpTunnelTable | not-accessible | current | The mplsTeP2mpTunnelTable allows new P2MP MPLS tunnels to be created between an LSR and one or more remote end-points, and existing P2MP tunnels to be reconfig… |
| 1.3.6.1.4.1.2636.5.7.1.2.1.1 | RowjnxMplsTeP2mpTunnelEntry | not-accessible | current | An entry in this table represents a P2MP MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling… |
| 1.3.6.1.4.1.2636.5.7.1.2.1.1.2 | ColumnjnxMplsTeP2mpTunnelP2mpIntegrity | read-create | current | Denotes whether or not P2MP Integrity is required for this tunnel. If P2MP integrity is operational on a P2MP tunnel then the failure of the path to any of the… |
| 1.3.6.1.4.1.2636.5.7.1.2.1.1.3 | ColumnjnxMplsTeP2mpTunnelBranchRole | read-create | current | This value supplements the value in the object mplsTunnelRole in MPLS-TE-STD-MIB that indicates the role of this LSR in the tunnel represented by this entry in… |
| 1.3.6.1.4.1.2636.5.7.1.2.1.1.4 | ColumnjnxMplsTeP2mpTunnelP2mpXcIndex | read-only | current | This object contains the value of mplsXCIndex, the primary index of the mplsXCTable for all cross-connect entries for this P2MP LSP. If no XC entries have been… |
| 1.3.6.1.4.1.2636.5.7.1.2.1.1.5 | ColumnjnxMplsTeP2mpTunnelRowStatus | read-create | current | This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modif… |
| 1.3.6.1.4.1.2636.5.7.1.2.1.1.6 | ColumnjnxMplsTeP2mpTunnelStorageType | read-create | current | The storage type for this tunnel entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.4.1.2636.5.7.1.2.2 | ScalarjnxMplsTeP2mpTunnelSubGroupIDNext | read-only | current | This object contains an unused value for mplsTeP2mpTunnelDestSubGroupID, or a zero to indicate that none exists. Negative values are not allowed, as they do no… |
| 1.3.6.1.4.1.2636.5.7.1.2.3 | TablejnxMplsTeP2mpTunnelDestTable | not-accessible | current | The mplsTeP2mpTunnelDestTable allows new destinations of P2MP MPLS tunnels to be added to and removed from P2MP tunnels. |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1 | RowjnxMplsTeP2mpTunnelDestEntry | not-accessible | current | An entry in this table represents a destination of a P2MP MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by … |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.1 | ColumnjnxMplsTeP2mpTunnelDestSrcSubGroupOriginType | not-accessible | current | This object identifies the type of address carried in mplsTeP2mpTunnelDestSrcSubGroupOrigin. Since the object mplsTeP2mpTunnelDestSrcSubGroupOrigin must confor… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.2 | ColumnjnxMplsTeP2mpTunnelDestSrcSubGroupOrigin | not-accessible | current | The TE Router ID (reachable and stable IP address) of the originator of the P2MP sub-group as received on a Path message by a transit or egress LSR. This objec… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.3 | ColumnjnxMplsTeP2mpTunnelDestSrcSubGroupID | not-accessible | current | The unique identifier assigned by the sub-group originator for this sub-group of this P2MP tunnel as received on a Path message by a transit or egress LSR. The… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.4 | ColumnjnxMplsTeP2mpTunnelDestSubGroupOriginType | not-accessible | current | This object identifies the type of address carried in mplsTeP2mpTunnelDestSubGroupOrigin. This object must return either ipv4(1) or ipv6(2) in keeping with the… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.5 | ColumnjnxMplsTeP2mpTunnelDestSubGroupOrigin | not-accessible | current | The TE Router ID (reachable and stable IP address) of the originator of the P2MP sub-group. In many cases, this will be the ingress LSR of the P2MP tunnel and … |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.6 | ColumnjnxMplsTeP2mpTunnelDestSubGroupID | not-accessible | current | The unique identifier assigned by the sub-group originator for this sub-group of this P2MP tunnel. An appropriate value for this object during row creation whe… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.7 | ColumnjnxMplsTeP2mpTunnelDestDestinationType | not-accessible | current | This object identifies the type of address carried in mplsTeP2mpTunnelDestDestination. This object forms part of the index of this table and can, therefore, no… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.8 | ColumnjnxMplsTeP2mpTunnelDestDestination | not-accessible | current | A single destination of this P2MP tunnel. That is, a routable TE address of a leaf. This will often be the TE Router ID of the leaf, but can be any interface a… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.9 | ColumnjnxMplsTeP2mpTunnelDestBranchOutSegment | read-only | current | This object identifies the outgoing branch from this LSR towards the destination represented by this table entry. It must be a unique identifier within the sco… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.10 | ColumnjnxMplsTeP2mpTunnelDestHopTableIndex | read-create | current | Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this destination of the P2MP tunnel. This object represents the configured r… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.11 | ColumnjnxMplsTeP2mpTunnelDestPathInUse | read-create | current | This value denotes the configured path that was chosen as the explicit path to this destination of this P2MP tunnel. This value reflects the secondary index in… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.12 | ColumnjnxMplsTeP2mpTunnelDestCHopTableIndex | read-only | current | Index into the mplsTunnelCHopTable that identifies the explicit path for this destination of the P2MP tunnel. This path is based on the chosen configured path … |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.13 | ColumnjnxMplsTeP2mpTunnelDestARHopTableIndex | read-only | current | Index into the mplsTunnelARHopTable that identifies the actual hops traversed to this destination of the P2MP tunnel. This is automatically updated by the agen… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.14 | ColumnjnxMplsTeP2mpTunnelDestTotalUpTime | read-only | current | This value represents the aggregate up time for all instances of this tunnel to this destination, if this information is available. If this information is not … |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.15 | ColumnjnxMplsTeP2mpTunnelDestInstanceUpTime | read-only | current | This value identifies the total time that the currently active tunnel instance to this destination has had its operational status (mplsTeP2mpTunnelDestOperStat… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.16 | ColumnjnxMplsTeP2mpTunnelDestPathChanges | read-only | current | This object counts the number of times the actual path for this destination of this P2MP tunnel instance has changed. This object should be read in conjunction… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.17 | ColumnjnxMplsTeP2mpTunnelDestLastPathChange | read-only | current | Specifies the time since the last change to the actual path for this destination of this P2MP tunnel instance. |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.18 | ColumnjnxMplsTeP2mpTunnelDestCreationTime | read-only | current | Specifies the value of sysUpTime when the first instance of this tunnel came into existence for this destination. That is, when the value of mplsTeP2mpTunnelDe… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.19 | ColumnjnxMplsTeP2mpTunnelDestStateTransitions | read-only | current | This object counts the number of times the status (mplsTeP2mpTunnelDestOperStatus) of this tunnel instance to this destination has changed. This object should … |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.20 | ColumnjnxMplsTeP2mpTunnelDestDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this row's Counter32 objects experienced a discontinuity. If no such discontinui… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.21 | ColumnjnxMplsTeP2mpTunnelDestAdminStatus | read-create | current | Indicates the desired operational status of this destination of this P2MP tunnel. |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.22 | ColumnjnxMplsTeP2mpTunnelDestOperStatus | read-only | current | Indicates the actual operational status of this destination of this P2MP tunnel. This object may be compared to mplsTunnelOperStatus that includes two other va… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.23 | ColumnjnxMplsTeP2mpTunnelDestRowStatus | read-create | current | This object is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modifie… |
| 1.3.6.1.4.1.2636.5.7.1.2.3.1.24 | ColumnjnxMplsTeP2mpTunnelDestStorageType | read-create | current | The storage type for this table entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.4.1.2636.5.7.1.2.4 | TablejnxMplsTeP2mpTunnelBranchPerfTable | not-accessible | current | This table provides per-tunnel branch MPLS performance information. This table is not valid for switching types other than packet. |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1 | RowjnxMplsTeP2mpTunnelBranchPerfEntry | not-accessible | current | An entry in this table is created by the LSR for each downstream branch (out-segment) from this LSR for this P2MP tunnel. More than one destination as represen… |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1.1 | ColumnjnxMplsTeP2mpTunnelBranchPerfBranch | not-accessible | current | This object identifies an outgoing branch from this LSR for this tunnel. Its value is unique within the context of the tunnel. If MPLS-LSR-STD-MIB is implement… |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1.2 | ColumnjnxMplsTeP2mpTunnelBranchPerfPackets | read-only | current | Number of packets forwarded by the tunnel onto this branch. This object should represents the 32-bit value of the least significant part of the 64-bit value if… |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1.3 | ColumnjnxMplsTeP2mpTunnelBranchPerfHCPackets | read-only | current | High capacity counter for number of packets forwarded by the tunnel onto this branch. This object should be read in conjunction with mplsTeP2mpTunnelBranchDisc… |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1.4 | ColumnjnxMplsTeP2mpTunnelBranchPerfErrors | read-only | current | Number of packets dropped because of errors or for other reasons, that were supposed to be forwarded onto this branch for this tunnel. This object should be re… |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1.5 | ColumnjnxMplsTeP2mpTunnelBranchPerfBytes | read-only | current | Number of bytes forwarded by the tunnel onto this branch. This object should represents the 32-bit value of the least significant part of the 64-bit value if b… |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1.6 | ColumnjnxMplsTeP2mpTunnelBranchPerfHCBytes | read-only | current | High capacity counter for number of bytes forwarded by the tunnel onto this branch. This object should be read in conjunction with mplsTeP2mpTunnelBranchDiscon… |
| 1.3.6.1.4.1.2636.5.7.1.2.4.1.7 | ColumnjnxMplsTeP2mpTunnelBranchDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this row's Counter32 or Counter64 objects experienced a discontinuity. If no suc… |
| 1.3.6.1.4.1.2636.5.7.1.2.5 | ScalarjnxMplsTeP2mpTunnelNotificationEnable | read-write | current | If this object is true(1), then it enables the generation of mplsTeP2mpTunnelDestUp and mplsTeP2mpTunnelDestDown notifications. Otherwise these notifications a… |
| 1.3.6.1.4.1.2636.5.7.1.3 | NodejnxMplsTeP2mpConformance | |||
| 1.3.6.1.4.1.2636.5.7.1.3.1 | NodejnxMplsTeP2mpGroups | |||
| 1.3.6.1.4.1.2636.5.7.1.3.1.1 | GroupjnxMplsTeP2mpGeneralGroup | current | Collection of objects needed for MPLS P2MP. | |
| 1.3.6.1.4.1.2636.5.7.1.3.1.2 | GroupjnxMplsTeP2mpNotifGroup | current | Notifications implemented in this module. | |
| 1.3.6.1.4.1.2636.5.7.1.3.1.3 | GroupjnxMplsTeP2mpScalarGroup | current | Scalar objects needed to implement P2MP MPLS tunnels. | |
| 1.3.6.1.4.1.2636.5.7.1.3.2 | NodejnxMplsTeP2mpCompliances | |||
| 1.3.6.1.4.1.2636.5.7.1.3.2.1 | CompliancejnxMplsTeP2mpModuleFullCompliance | current | Compliance statement for agents that provide full support for MPLS-TE-P2MP-STD-MIB. Such devices can be monitored and also be configured using this MIB module.… | |
| 1.3.6.1.4.1.2636.5.7.1.3.2.2 | CompliancejnxMplsTeP2mpModuleReadOnlyCompliance | read-only | current | Compliance statement for agents that provide read-only support for MPLS-TE-P2MP-STD-MIB. Such devices can only be monitored using this MIB module. The Module i… |