CM-SA-MIB
582 objects
This module defines the Service Assurance MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
Imported Objects
| ADVA-MIB | fsp150cm |
| CM-COMMON-MIB | AdminState ClassOfServiceType CmPmBinAction IpPriorityMapMode IpVersion MepDestinationType OperationalState PerfCounter32 PerfCounter64 SchedActivityStatus ScheduleType SecondaryState TrafficDirection VlanId VlanPriority |
| CM-ENTITY-MIB | neIndex shelfIndex slotIndex |
| CM-FACILITY-MIB | BitErrRate PolicerColorMode |
| IEEE8021-CFM-MIB | Dot1agCfmMepIdOrZero |
| IPV6-TC | Ipv6Address |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter64 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString MacAddress RowStatus StorageType TEXTUAL-CONVENTION TruthValue VariablePointer |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2544.1.12.8 | IdentitycmServiceAssuranceMIB | This module defines the Service Assurance MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking. | ||
| 1.3.6.1.4.1.2544.1.12.8.1 | NodecmServAssuranceObjects | |||
| 1.3.6.1.4.1.2544.1.12.8.1.1 | TableecpaControlTable | not-accessible | current | A list of entries for the control of Etherjack Connection Performance Analyzer Streams. Upto 12 ECPA streams can be configured per test head; 3 ECPA streams ca… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1 | RowecpaControlEntry | not-accessible | current | A conceptual row in the ecpaControlTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.1 | ColumnecpaControlIndex | read-only | current | An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer Control Test head. There is only one test head per ca… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.2 | ColumnecpaControlSourcePort | read-write | current | Pointer to the Access or Network Port on which the ECPA test will be started within a card. |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.3 | ColumnecpaControlTestType | read-write | current | The type of ECPA test to be performed. When 'duration' test is specified, ECPA test is run for 'ecpaControlDuration' time. When 'numFrames' test is specified, … |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.4 | ColumnecpaControlNumFrames | read-write | current | This object enables specification of the number of frames for traffic generation. Traffic Generation will be completed after the specified number of frames are… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.5 | ColumnecpaControlDuration | read-write | current | This object enables specification of the time in seconds for traffic generation. Traffic Generation will be stopped after the specified time interval is exhaus… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.6 | ColumnecpaControlInjectorDirection | read-write | current | This object enables specification of the direction of traffic generation. This value must be specified if the interface is used for traffic generation. Both of… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.7 | ColumnecpaControlMonitorDirection | read-write | current | This object enables specification of the direction of receival of generated traffic. This value must be specified if the interface is used for receiving/monito… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.8 | ColumnecpaControlStream1 | read-write | current | This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream1. Non 0 valu… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.9 | ColumnecpaControlStream2 | read-write | current | This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream2. Non 0 valu… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.10 | ColumnecpaControlStream3 | read-write | current | This object specifies which stream should be included in the ECPA execution. Value of 0 indicates that no streams is selected by ecpaControlStream3. Non 0 valu… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.11 | ColumnecpaControlAction | read-write | current | This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creati… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.12 | ColumnecpaControlTestStatus | read-only | current | This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress… |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.13 | ColumnecpaControlStorageType | read-create | current | The type of storage configured for this entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.1.1.14 | ColumnecpaControlRowStatus | read-create | current | The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description … |
| 1.3.6.1.4.1.2544.1.12.8.1.2 | TableecpaConfigStreamTable | not-accessible | current | A list of entries for the configuration of Etherjack Connection Performance Analyzer Stream Specifications. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1 | RowecpaConfigStreamEntry | not-accessible | current | A conceptual row in the ecpaConfigStreamTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.1 | ColumnecpaConfigStreamIndex | read-write | current | An arbitrary integer index value used to uniquely identify this Etherjack Connection Performance Analyzer. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.2 | ColumnecpaConfigStreamName | read-write | current | Symbolic Stream Name that can be associated with an ECPA stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.3 | ColumnecpaConfigStreamFrameSize | read-write | current | This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used. CM Aggregati… |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.4 | ColumnecpaConfigStreamRate | read-write | current | The object enables specification of the traffic generation rate. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.5 | ColumnecpaConfigStreamPayloadType | read-write | current | This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates t… |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.6 | ColumnecpaConfigStreamSignature | read-write | current | Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame re… |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.7 | ColumnecpaConfigStreamDestinationMAC | read-write | current | Allows specification of destination MAC in the generated traffic. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.8 | ColumnecpaConfigStreamSourceMAC | read-write | current | Allows specification of source MAC in the generated traffic. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.9 | ColumnecpaConfigStreamOuterVlanEnabled | read-write | current | Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly … |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.10 | ColumnecpaConfigStreamOuterVlanId | read-write | current | Outer VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.11 | ColumnecpaConfigStreamOuterVlanPrio | read-write | current | Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.12 | ColumnecpaConfigStreamOuterVlanEtherType | read-write | current | EtherType associated with the Outer VLAN Tag. Valid only if ecpaConfigStreamOuterVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.13 | ColumnecpaConfigStreamInnerVlanEnabled | read-write | current | Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly … |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.14 | ColumnecpaConfigStreamInnerVlanId | read-write | current | Inner VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.15 | ColumnecpaConfigStreamInnerVlanPrio | read-write | current | Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.16 | ColumnecpaConfigStreamInnerVlanEtherType | read-write | current | EtherType associated with the Inner VLAN Tag. Valid only if ecpaConfigStreamInnerVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.17 | ColumnecpaConfigStreamIpVersion | read-write | current | This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows tes… |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.18 | ColumnecpaConfigStreamIpV4Address | read-write | current | This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.19 | ColumnecpaConfigStreamIpV6Address | read-write | current | This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.20 | ColumnecpaConfigStreamPrioMapMode | read-write | current | This object enables specification of Priority Mapping Mode for the test stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.21 | ColumnecpaConfigStreamPrioVal | read-write | current | This object enables specification of Priority Value for ecpaConfigStreamPrioMapMode as TOS/DSCP. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.22 | ColumnecpaConfigStreamInnerVlan2Enabled | read-write | current | Allows specification of a VLAN tagged ECPA stream. This variable enables the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a thre… |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.23 | ColumnecpaConfigStreamInnerVlan2Id | read-write | current | Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.24 | ColumnecpaConfigStreamInnerVlan2Prio | read-write | current | Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.25 | ColumnecpaConfigStreamInnerVlan2EtherType | read-write | current | EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaConfigStreamInnerVlan2Enabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.26 | ColumnecpaConfigStreamDestIpV4Address | read-write | current | This object enables specification of destination ipv4 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv4. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.27 | ColumnecpaConfigStreamDestIpV6Address | read-write | current | This object enables specification of destination ipv6 IP Address for the test stream.This is used when ecpaConfigStreamIpVersion is ipv6. |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.28 | ColumnecpaConfigStreamUsePortSourceMAC | read-write | current | This object when not enabled indicates that MAC Address specified by ecpaConfigStreamSourceMAC as the source MAC Address of the ECPA test stream. For EGX, if e… |
| 1.3.6.1.4.1.2544.1.12.8.1.2.1.29 | ColumnecpaConfigStreamRateHi | read-write | current | The object enables specification of the higher 32 bits of the traffic generation rate. |
| 1.3.6.1.4.1.2544.1.12.8.1.3 | TableecpaTestStreamTable | not-accessible | current | A list of entries containing results of a previous test. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1 | RowecpaTestStreamEntry | not-accessible | current | A conceptual row in the ecpaTestStreamTable. Entries in this table show results of the current ECPA test. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.1 | ColumnecpaTestStreamIndex | read-only | current | An integer index value corresponding to the stream index for which the ECPA test was initiated. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.2 | ColumnecpaTestStreamSourcePort | read-only | current | An integer index value corresponding to the ifIndex for which the ECPA test was initiated. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.3 | ColumnecpaTestStreamName | read-write | current | Symbolic Stream Name that can be associated with an ECPA stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.4 | ColumnecpaTestStreamFrameSize | read-write | current | This object enables specification of fixed length frame size in bytes for traffic generation. If not specified, default value of 64 bytes is used. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.5 | ColumnecpaTestStreamRate | read-write | current | The object enables specification of the traffic generation rate. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.6 | ColumnecpaTestStreamPayloadType | read-write | current | This object enables specification of type of payload to generate `fixed' type indicates a generation pattern of 5A, A5, 5A, A5 bytes. `random' type indicates t… |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.7 | ColumnecpaTestStreamSignature | read-write | current | Indicates an 8-byte signature specified by the user in hexadecimal or ASCII format. This signature is currently used by the FSP150Mx products for test frame re… |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.8 | ColumnecpaTestStreamDestinationMAC | read-write | current | Allows specification of destination MAC in the generated traffic. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.9 | ColumnecpaTestStreamSourceMAC | read-write | current | Allows specification of source MAC in the generated traffic. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.10 | ColumnecpaTestStreamOuterVlanEnabled | read-write | current | Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly … |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.11 | ColumnecpaTestStreamOuterVlanId | read-write | current | Outer VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.12 | ColumnecpaTestStreamOuterVlanPrio | read-write | current | Outer VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamOuterVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.13 | ColumnecpaTestStreamOuterVlanEtherType | read-write | current | EtherType associated with the Outer VLAN Tag. Valid only if ecpaTestStreamOuterVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.14 | ColumnecpaTestStreamInnerVlanEnabled | read-write | current | Allows specification of a VLAN tagged ECPA stream. This variable enables the outer VLAN specification, in the case of a doubly tagged ECPA stream. If a singly … |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.15 | ColumnecpaTestStreamInnerVlanId | read-write | current | Inner VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.16 | ColumnecpaTestStreamInnerVlanPrio | read-write | current | Inner VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.17 | ColumnecpaTestStreamInnerVlanEtherType | read-write | current | EtherType associated with the Inner VLAN Tag. Valid only if ecpaTestStreamInnerVlanEnabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.18 | ColumnecpaTestStreamIpVersion | read-write | current | This object enables specification of IP data in the generated test traffic. Value of `ipv4' allows test data to be IP v4 compatible. Value of `ipv6' allows tes… |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.19 | ColumnecpaTestStreamIpV4Address | read-write | current | This object enables specification of ipv4 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv4. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.20 | ColumnecpaTestStreamIpV6Address | read-write | current | This object enables specification of ipv6 IP Address for the test stream.This is used when ecpaTestStreamIpVersion is ipv6. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.21 | ColumnecpaTestStreamPrioMapMode | read-write | current | This object enables specification of Priority Mapping Mode for the test stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.22 | ColumnecpaTestStreamPrioVal | read-write | current | This object enables specification of Priority Value for ecpaTestStreamPrioMapMode as TOS/DSCP. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.23 | ColumnecpaTestStreamMonStartTime | read-only | current | The start time of the ECPA test for this stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.24 | ColumnecpaTestStreamMonEndTime | read-only | current | The end time of the ECPA test for this stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.25 | ColumnecpaTestStreamMonElapsedTime | read-only | current | The elapsed time of ECPA test for this stream in seconds. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.26 | ColumnecpaTestStreamMonTxFrames | read-only | current | The total number of frames transmitted(generated) so far. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.27 | ColumnecpaTestStreamMonRxFrames | read-only | current | The total number of frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.28 | ColumnecpaTestStreamMonRxPercentSuccess | read-only | current | Received frames as a percentage of transmitted frames. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.29 | ColumnecpaTestStreamMonRxOutOfSeqErrs | read-only | current | The total number of out of sequence errors received so far. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.30 | ColumnecpaTestStreamMonRxSeqGaps | read-only | current | The total number of sequence gaps received so far. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.31 | ColumnecpaTestStreamMonRxNonEcpaFrames | read-only | current | The total number of non ECPA frames received during the execution. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.32 | ColumnecpaTestStreamMonRxMinDelay | read-only | current | The minimum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.33 | ColumnecpaTestStreamMonRxMaxDelay | read-only | current | The maximum delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.34 | ColumnecpaTestStreamMonRxAvgDelay | read-only | current | The average delay (in microseconds) across all frames received so far. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.35 | ColumnecpaTestStreamMonRx1stFrameSize | read-only | current | Frame size of the Monitored First Frame. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.36 | ColumnecpaTestStreamMonRx1stFrame1Octets | read-only | current | The frame contents of the first received frame - first 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.37 | ColumnecpaTestStreamMonRx1stFrame2Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.38 | ColumnecpaTestStreamMonRx1stFrame3Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.39 | ColumnecpaTestStreamMonRx1stFrame4Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.40 | ColumnecpaTestStreamMonRx1stFrame5Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.41 | ColumnecpaTestStreamMonRx1stFrame6Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.42 | ColumnecpaTestStreamMonRx1stFrame7Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.43 | ColumnecpaTestStreamMonRx1stFrame8Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.44 | ColumnecpaTestStreamMonRx1stFrame9Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.45 | ColumnecpaTestStreamMonRx1stFrame10Octets | read-only | current | The frame contents of the first received frame - next 1024 bytes. This object does not exist if the ecpaControlTestStatus indicates initial state. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.46 | ColumnecpaTestStreamMonRxBitRate | read-only | current | The object provides the average bit rate on the ECPA test stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.47 | ColumnecpaTestStreamInnerVlan2Enabled | read-only | current | This variable indicates the second(inner) VLAN specification, in the case of a 3-tagged ECPA stream. If a three tagged ECPA stream is desired, this indicates t… |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.48 | ColumnecpaTestStreamInnerVlan2Id | read-only | current | This variable provides the Inner (second) VLAN Id associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.49 | ColumnecpaTestStreamInnerVlan2Prio | read-only | current | This variable provides the Inner (second) VLAN Priority associated with the ECPA stream. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.50 | ColumnecpaTestStreamInnerVlan2EtherType | read-only | current | This variable provides the EtherType associated with the Inner (second) VLAN Tag. Valid only if ecpaTestStreamInnerVlan2Enabled is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.51 | ColumnecpaTestStreamDestIpV4Address | read-only | current | This object provides the destination ipv4 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv4. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.52 | ColumnecpaTestStreamDestIpV6Address | read-only | current | This object provides the destination ipv6 IP Address for the test stream. This is valid when ecpaTestStreamIpVersion is ipv6. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.53 | ColumnecpaTestStreamConfigChanged | read-only | current | This object provides information on whether the associated ecpaConfigStream is changed. |
| 1.3.6.1.4.1.2544.1.12.8.1.3.1.54 | ColumnecpaTestStreamRateHi | read-write | current | The object enables specification of the higher 32 bits of the traffic generation rate. |
| 1.3.6.1.4.1.2544.1.12.8.1.4 | TableesaProbeTable | not-accessible | current | A list of entries corresponding to ESA Probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1 | RowesaProbeEntry | not-accessible | current | A row in the esaProbeTable. Entries can be created in this table by management application action. The slotIndex should be 255 if the product is cm5.1. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.1 | ColumnesaProbeIndex | read-only | current | An integer index value used to uniquely identify this ESA Probe within a Card. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.2 | ColumnesaProbeName | read-create | current | A unique identifier used by the Manager to distinguish the ESA Probe. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.3 | ColumnesaProbeSourcePort | read-create | current | This object points to the Port to which the ESA Probe is attached, i.e.on which the service to be monitored resides. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.4 | ColumnesaProbeAssocSchedGroup | read-only | current | This object points to the probe's associated Scheduled Group. Initially, when the probe is not associated with a Group, this object's value is set to {0.0}. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.5 | ColumnesaProbeDirection | read-create | current | This object allows to specify the direction of Probe traffic generation. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.6 | ColumnesaProbeProtocol | read-create | current | Protocol to be used in ESA Probe messages. 'icmpTimestamp', 'icmpEcho', 'udpEcho' protocols support layer-3 ethernet service assurance. If the remote reflector… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.7 | ColumnesaProbeSrcIpAddress | read-create | current | Variable that allows specification of the Probe's source IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as source add… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.8 | ColumnesaProbeSrcSubnetMask | read-create | current | Variable that allows specification of the Probe's source IP Subnet Mask. NOTE: This attribute is not applicable to Y.1731 probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.9 | ColumnesaProbeDestIpAddress | read-create | current | Variable that allows specification of the Reflector's destination IP Address. This IP Address is used in the IP header of the ESA Probe generated packets, as d… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.10 | ColumnesaProbeSrcMep | read-create | current | This attribute is applicable only for Y.1731 probes. It identifies the source MEP that initiates the Y.1731 LMMs and DMMs. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.11 | ColumnesaProbeDestMepType | read-create | current | This attribute is applicable only for Y.1731 probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestMepId. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.12 | ColumnesaProbeDestMepMacAddr | read-create | current | This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. This MAC address will be the destina… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.13 | ColumnesaProbeDestMepId | read-create | current | This attribute is applicable only for Y.1731 probes. It identifies the destination MEP that responds to the LMMs and DMMs. The MAC address of this RMEP ID from… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.14 | ColumnesaProbeVlanTagEnabled | read-write | current | Ability to specify whether or not to use VLAN tagged or untagged ESA traffic generation on the Probe. NOTE: This attribute is not applicable to Y.1731 probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.15 | ColumnesaProbeVlanTagEtherType | read-write | current | This variable allows the user to specify the monitored service's VLAN tag Ether Type. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attrib… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.16 | ColumnesaProbeVlanId | read-write | current | This variable allows the user to specify the monitored service's VLAN tag. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is not … |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.17 | ColumnesaProbeVlanPrio | read-write | current | This variable allows the user to specify the monitored service's VLAN priority. Valid if 'esaProbeVlanTagEnabled' is specified as TRUE. NOTE: This attribute is… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.18 | ColumnesaProbeInnerVlanTagEnabled | read-write | current | Ability to specify whether or not to use Inner VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.19 | ColumnesaProbeInnerVlanTagEtherType | read-write | current | This variable allows the user to specify the monitored service's Inner VLAN tag Ether Type. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: … |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.20 | ColumnesaProbeInnerVlanId | read-write | current | This variable allows the user to specify the monitored service's Inner VLAN tag. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This attrib… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.21 | ColumnesaProbeInnerVlanPrio | read-write | current | This variable allows the user to specify the monitored service's Inner VLAN priority. Valid if 'esaProbeInnerVlanTagEnabled' is specified as TRUE. NOTE: This a… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.22 | ColumnesaProbeIpPrioMapMode | read-write | current | This object enables specification of Priority Mapping Mode for the ESA Probe. NOTE: This attribute is not applicable to Y.1731 probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.23 | ColumnesaProbeIpPriority | read-write | current | This object enables specification of Priority Value for esaProbePrioMapMode as priomap-tos,priomap-dscp. NOTE: This attribute is not applicable to Y.1731 probe… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.24 | ColumnesaProbePktsPerSample | read-write | current | This object enables specification of number of packets within a sample run for ESA traffic generation. A non-zero value must be specified. NOTE: This attribute… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.25 | ColumnesaProbePktSize | read-write | current | This object enables specification of fixed length frame size in bytes for ESA traffic generation. If not specified, default value of 104 bytes is used. NOTE: T… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.26 | ColumnesaProbeInterPktGap | read-write | current | This object enables specification of interval in milliseconds between packet generation. A non-zero value must be specified. NOTE: This attribute is not applic… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.27 | ColumnesaProbePktDeadInterval | read-write | current | This object enables specification of the dead interval in seconds after 'esaProbePktsPerSample' have been generated within the sample. This allows for settling… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.28 | ColumnesaProbeResponseTimeout | read-write | current | This object allows specification of the timeout value to determine lost packets. Time specified in seconds. NOTE: This attribute is not applicable to Y.1731 pr… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.29 | ColumnesaProbeY1731DmmPktSize | read-write | current | This object is only applicable to Y.1731 probes. This object enables specification of the TLV size for Delay Measurement Frames (DMMs). Value of 0 is a read-on… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.30 | ColumnesaProbeY1731LmmInterval | read-create | current | LMM frame transmission period. For Loss Measurement Frames, only interval-1sec is supported. This attribute is only applicable to Y.1731 probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.31 | ColumnesaProbeY1731DmmInterval | read-create | current | DMM frame transmission period. This attribute is only applicable to Y.1731 probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.32 | ColumnesaProbeHistoryBins | read-write | current | This object allows specification of number of history bins. This is the total history data that will be maintained for an ESA Probe run, at any instance. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.33 | ColumnesaProbeHistoryInterval | read-write | current | This object allows specification of the history interval period. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.34 | ColumnesaProbeDistHistoryBins | read-write | current | This object allows specification of number of distribution history bins. This is the total history distribution data that will be maintained for an ESA Probe r… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.35 | ColumnesaProbeDistHistoryInterval | read-write | current | This object allows specification of the history distribution interval period. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.36 | ColumnesaProbeCreationTime | read-only | current | This object provides the creation time of the ESA Probe. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.37 | ColumnesaProbeStorageType | read-create | current | The type of storage configured for this entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.38 | ColumnesaProbeRowStatus | read-create | current | The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description … |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.39 | ColumnesaProbeMultiCOSEnabled | read-create | current | This object is introduced for FSP150CC Release 4.3. This object is only applicable for Y.1731 and SLM-SLR Probe Protocol Types. This object can be used to spec… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.40 | ColumnesaProbeSLAMonitorType | read-create | current | This object indicates whether the Probe is a point-to-point type or a point-to-multipoint type. Only SLM-SLR probes can be point-to-multipoint. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.41 | ColumnesaProbeCOSType | read-create | current | This object can be used to specify the first Class of Service associated with the Y.1731/SLM-SLR ESA Probe. In the case of a multiCOS Probe, this object has no… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.42 | ColumnesaProbeSLMMulticastMACEnabled | read-create | current | This object can be used to specify whether the SLM/SLR protocol Probe will use multicast MAC address in SLM (Synthetic Loss Measurement) messages. This object … |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.43 | ColumnesaProbeSOAMInterval | read-create | current | This object can be used to specify the packet interval type for Y.1731 LM/DM and SLM/SLR based ESA Probes, for the first Class of Service. In the case of a mul… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.44 | ColumnesaProbeSOAMPktSize | read-write | current | This object can be used to specify the packet size for SLM-SLR based ESA Probes, for the first Class of Service. In the case of multiCOS Probe, this object has… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.45 | ColumnesaProbeInner2VlanTagEnabled | read-write | current | Ability to specify whether or not to use Inner2 VLAN tag. NOTE: This attribute is not applicable to Y.1731 probes. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.46 | ColumnesaProbeInner2VlanTagEtherType | read-write | current | This variable allows the user to specify the monitored service's Inner2 VLAN tag Ether Type. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.47 | ColumnesaProbeInner2VlanId | read-write | current | This variable allows the user to specify the monitored service's Inner2 VLAN tag. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This attr… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.48 | ColumnesaProbeInner2VlanPrio | read-write | current | This variable allows the user to specify the monitored service's Inner2 VLAN priority. Valid if 'esaProbeInner2VlanTagEnabled' is specified as TRUE. NOTE: This… |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.49 | ColumnesaProbeAdminState | read-only | current | This object represents the Administrative State of the ESA Probe. This is not externally managed. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.50 | ColumnesaProbeOperationalState | read-only | current | This object represents the Operational State of the ESA Probe. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.51 | ColumnesaProbeSecondaryState | read-only | current | This object represents the Secondary State of the ESA Probe. |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.52 | ColumnesaProbeMacAddress | read-only | current | This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using |
| 1.3.6.1.4.1.2544.1.12.8.1.4.1.53 | ColumnesaProbeAlias | read-create | current | This object allows SNMP management entities to provide an alias for an ESA Probe. |
| 1.3.6.1.4.1.2544.1.12.8.1.5 | TableesaProbeScheduleGroupTable | not-accessible | current | A list of entries that allow groups of ESA Probes to be scheduled. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1 | RowesaProbeScheduleGroupEntry | not-accessible | current | A row in esaProbeScheduleGroupTable. Entries are created in this table by management application action. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.1 | ColumnesaProbeScheduleGroupIndex | read-create | current | A unique index to distinguish the ESA Probe Schedule Group. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.2 | ColumnesaProbeScheduleGroupDescr | read-create | current | Description of the probe schedule group. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.3 | ColumnesaProbeScheduleGroupProbeList | read-create | current | A comma separated list of esaProbeName's, that will have the same schedule. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.4 | ColumnesaProbeScheduleGroupType | read-create | current | This object allows to specify whether the ESA probe group schedule is 'one-shot' or 'periodic'. A 'one-shot' schedule executes only once and then stops. A 'per… |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.5 | ColumnesaProbeScheduleGroupStartTime | read-create | current | This object allows specification of the start time of the ESA Probe Group. Value of time less than current system time will equate to current time. When the sy… |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.6 | ColumnesaProbeScheduleGroupDuration | read-create | current | This object allows specification of the duration in 'seconds' for ESA Probe Group run. Note that a value of 4294967295 means Duration as FOREVER. FOREVER value… |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.7 | ColumnesaProbeScheduleGroupInterval | read-create | current | This object allows specification of the interval in 'seconds' between successive runs for ESA Probe Group. This variable is only valid if the 'esaProbeSchedule… |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.8 | ColumnesaProbeScheduleGroupAction | read-write | current | This object allows to suspend/resume the ESA scheduled group. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.9 | ColumnesaProbeScheduleGroupStatus | read-only | current | This object indicates the current status of the ESA Probe Group. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.10 | ColumnesaProbeScheduleGroupStorageType | read-create | current | The type of storage configured for this entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.11 | ColumnesaProbeScheduleGroupRowStatus | read-create | current | The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description … |
| 1.3.6.1.4.1.2544.1.12.8.1.5.1.12 | ColumnesaProbeScheduleGroupActionProbeList | read-write | current | A comma separated list of esaProbeName's, if set esaProbeScheduleGroupAction as add or remove, they will be add or remove from esaProbeScheduleGroupProbeList. |
| 1.3.6.1.4.1.2544.1.12.8.1.6 | TableesaReflectorTable | not-accessible | current | A list of entries corresponding to ESA Reflectors. NOTE: There is no need to create reflectors for Y.1731 probes as the MEPs will respond by default. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1 | RowesaReflectorEntry | not-accessible | current | A row in the esaReflectorTable. Entries can be created in this table by management application action. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.1 | ColumnesaReflectorIndex | read-create | current | A unique index to distinguish the ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.2 | ColumnesaReflectorName | read-create | current | A unique identifier to distinguish the ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.3 | ColumnesaReflectorIpAddress | read-create | current | This object allows specification of the Reflector's IP Address. Reflector listens for packets destined at this IP Address. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.4 | ColumnesaReflectorSubnetMask | read-create | current | This object allows specification of the Reflector's IP Subnet mask. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.5 | ColumnesaReflectorSourcePort | read-create | current | This object points to the Port to which the ESA Reflector is attached, i.e.on which the service to be monitored resides. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.6 | ColumnesaReflectorIpPrioMapMode | read-write | current | This object enables specification of Priority Mapping Mode for the ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.7 | ColumnesaReflectorIpPriority | read-write | current | This object enables specification of Priority Value for esaReflectorPrioMapMode as priomap-tos,priomap-dscp. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.8 | ColumnesaReflectorAction | read-write | current | This object allows to suspend/resume the ESA reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.9 | ColumnesaReflectorSuspended | read-only | current | This object indicates whether the ESA Reflector is active or suspended. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.10 | ColumnesaReflectorCreationTime | read-only | current | This object provides the creation time of the ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.11 | ColumnesaReflectorStorageType | read-create | current | The type of storage configured for this entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.12 | ColumnesaReflectorRowStatus | read-create | current | The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description … |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.13 | ColumnesaReflectorDirection | read-create | current | This object provides the direction of the ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.14 | ColumnesaReflectorAdminState | read-only | current | This object represents the Administrative State of the ESA Reflector. This is not externally managed. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.15 | ColumnesaReflectorOperationalState | read-only | current | This object represents the Operational State of the ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.16 | ColumnesaReflectorSecondaryState | read-only | current | This object represents the Secondary State of the ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.17 | ColumnesaReflectorMacAddress | read-only | current | This attribute is applicable only for Y.1731 probes. It identifies the destination MacAddress which esa using |
| 1.3.6.1.4.1.2544.1.12.8.1.6.1.18 | ColumnesaReflectorAlias | read-create | current | This object allows SNMP management entities to provide an alias for an ESA Reflector. |
| 1.3.6.1.4.1.2544.1.12.8.1.7 | TableesaProbeStatsTable | not-accessible | current | A collection of ESA Probe related statistics kept for a particular ESA Probe entity. These reflect the current data. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1 | RowesaProbeStatsEntry | not-accessible | current | A conceptual row in the esaProbeStatsTable. An entry exists in this table for each ESA Probe. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.1 | ColumnesaProbeStatsDestinationIndex | read-only | current | An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since … |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.2 | ColumnesaProbeStatsCOSIndex | read-only | current | An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly speci… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.3 | ColumnesaProbeStatsIndex | read-only | current | An arbitrary integer index value used to uniquely identify this ESA Probe statistics entry. Index 1 corresponds to current and index 2 to rollover. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.4 | ColumnesaProbeStatsIntervalType | read-only | current | Indicates the type of collection, i.e. whether it is current, or rollover. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.5 | ColumnesaProbeStatsCOS | read-only | current | The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.6 | ColumnesaProbeStatsValid | read-only | current | Indicates the validity of the bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.7 | ColumnesaProbeStatsAction | read-write | current | Allows the Manager to clear the bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.8 | ColumnesaProbeStatsP2RPkts | read-only | current | The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) rec… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.9 | ColumnesaProbeStatsP2RErredPkts | read-only | current | The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet tra… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.10 | ColumnesaProbeStatsP2RSyncErrs | read-only | current | The number of (time) Synchronization Errors from probe to reflector in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.11 | ColumnesaProbeStatsP2RLostPkts | read-only | current | The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.12 | ColumnesaProbeStatsR2PPkts | read-only | current | The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) receiv… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.13 | ColumnesaProbeStatsR2PErredPkts | read-only | current | The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packe… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.14 | ColumnesaProbeStatsR2PSyncErrs | read-only | current | The number of (time) Synchronization Errors from reflector to probe in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.15 | ColumnesaProbeStatsR2PLostPkts | read-only | current | The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.16 | ColumnesaProbeStatsLostPkts | read-only | current | The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed … |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.17 | ColumnesaProbeStatsSeqGaps | read-only | current | The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq … |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.18 | ColumnesaProbeStatsOutOfSeqErrs | read-only | current | The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Receive… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.19 | ColumnesaProbeStatsMinRoundTripDelay | read-only | current | The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.20 | ColumnesaProbeStatsMaxRoundTripDelay | read-only | current | The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.21 | ColumnesaProbeStatsAvgRoundTripDelay | read-only | current | The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.22 | ColumnesaProbeStatsSumRoundTripDelay | read-only | current | The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.23 | ColumnesaProbeStatsSumOfSqRoundTripDelay | read-only | current | The sum of square of round trip delays in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.24 | ColumnesaProbeStatsMinOnewayP2RDelay | read-only | current | The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.25 | ColumnesaProbeStatsMaxOnewayP2RDelay | read-only | current | The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.26 | ColumnesaProbeStatsAvgOnewayP2RDelay | read-only | current | The average one-way source to destination delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.27 | ColumnesaProbeStatsSumOnewayP2RDelay | read-only | current | The total sum of one-way delay from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.28 | ColumnesaProbeStatsSumOfSqOnewayP2RDelay | read-only | current | The sum of square of one-way delay from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.29 | ColumnesaProbeStatsMinOnewayR2PDelay | read-only | current | The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.30 | ColumnesaProbeStatsMaxOnewayR2PDelay | read-only | current | The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.31 | ColumnesaProbeStatsAvgOnewayR2PDelay | read-only | current | The average one-way destination to source delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.32 | ColumnesaProbeStatsSumOnewayR2PDelay | read-only | current | The total sum of one-way delay from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.33 | ColumnesaProbeStatsSumOfSqOnewayR2PDelay | read-only | current | The sum of square of one-way delay from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.34 | ColumnesaProbeStatsMinPosP2RJitter | read-only | current | The minimum positive one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.35 | ColumnesaProbeStatsMaxPosP2RJitter | read-only | current | The maximum positive one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.36 | ColumnesaProbeStatsNumPosP2RJitter | read-only | current | The total number of positive one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.37 | ColumnesaProbeStatsSumPosP2RJitter | read-only | current | The total sum of positive one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.38 | ColumnesaProbeStatsSumOfSqPosP2RJitter | read-only | current | The sum of square of positive one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.39 | ColumnesaProbeStatsMinNegP2RJitter | read-only | current | The minimum negative one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.40 | ColumnesaProbeStatsMaxNegP2RJitter | read-only | current | The maximum negative one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.41 | ColumnesaProbeStatsNumNegP2RJitter | read-only | current | The total number of negative one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.42 | ColumnesaProbeStatsSumNegP2RJitter | read-only | current | The total sum of negative one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.43 | ColumnesaProbeStatsSumOfSqNegP2RJitter | read-only | current | The sum of square of negative one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.44 | ColumnesaProbeStatsMinPosR2PJitter | read-only | current | The minimum positive one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.45 | ColumnesaProbeStatsMaxPosR2PJitter | read-only | current | The maximum positive one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.46 | ColumnesaProbeStatsNumPosR2PJitter | read-only | current | The total number of positive one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.47 | ColumnesaProbeStatsSumPosR2PJitter | read-only | current | The total sum of positive one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.48 | ColumnesaProbeStatsSumOfSqPosR2PJitter | read-only | current | The sum of square of positive one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.49 | ColumnesaProbeStatsMinNegR2PJitter | read-only | current | The minimum negative one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.50 | ColumnesaProbeStatsMaxNegR2PJitter | read-only | current | The maximum negative one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.51 | ColumnesaProbeStatsNumNegR2PJitter | read-only | current | The total number of negative one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.52 | ColumnesaProbeStatsSumNegR2PJitter | read-only | current | The total sum of negative one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.53 | ColumnesaProbeStatsSumOfSqNegR2PJitter | read-only | current | The sum of square of negative one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.54 | ColumnesaProbeStatsY1731P2RNegLossOccurrences | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflect… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.55 | ColumnesaProbeStatsY1731R2PNegLossOccurrences | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.56 | ColumnesaProbeStatsY1731RxLmSamples | read-only | current | This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs receiv… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.57 | ColumnesaProbeStatsY1731RxDmSamples | read-only | current | This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs recei… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.58 | ColumnesaProbeStatsY1731P2RFrames | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destin… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.59 | ColumnesaProbeStatsY1731R2PFrames | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards t… |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.60 | ColumnesaProbeStatsAvgAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.61 | ColumnesaProbeStatsAvgAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.62 | ColumnesaProbeStatsMinAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.63 | ColumnesaProbeStatsMinAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.64 | ColumnesaProbeStatsMaxAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.65 | ColumnesaProbeStatsMaxAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.66 | ColumnesaProbeStatsNumAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.67 | ColumnesaProbeStatsNumAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.68 | ColumnesaProbeStatsSumAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.69 | ColumnesaProbeStatsSumAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.70 | ColumnesaProbeStatsSumOfSqAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.7.1.71 | ColumnesaProbeStatsSumOfSqAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.8 | TableesaProbeHistoryTable | not-accessible | current | A collection of ESA Probe related history kept for a particular ESA Probe entity. These reflect the current data. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1 | RowesaProbeHistoryEntry | not-accessible | current | A conceptual row in the esaProbeHistoryTable. An entry exists in this table for each ESA Probe. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.1 | ColumnesaProbeHistoryDestinationIndex | read-only | current | An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since … |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.2 | ColumnesaProbeHistoryCOSIndex | read-only | current | An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly speci… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.3 | ColumnesaProbeHistoryIndex | read-only | current | An arbitrary integer index value used to uniquely identify this ESA Probe statistics history entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.4 | ColumnesaProbeHistoryTime | read-only | current | Indicates the time of history bin creation. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.5 | ColumnesaProbeHistoryValid | read-only | current | Indicates the validity of the bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.6 | ColumnesaProbeHistoryAction | read-write | current | Allows the Manager to clear the bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.7 | ColumnesaProbeHistoryCOS | read-only | current | The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.8 | ColumnesaProbeHistoryP2RPkts | read-only | current | The total number of Transmitted Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) rec… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.9 | ColumnesaProbeHistoryP2RErredPkts | read-only | current | The total number of Packets in the current interval, for which there was a problem in transmission. This error is counted when there is a failure in packet tra… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.10 | ColumnesaProbeHistoryP2RSyncErrs | read-only | current | The number of (time) Synchronization Errors from probe to reflector in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.11 | ColumnesaProbeHistoryP2RLostPkts | read-only | current | The number of Lost Pkts from probe to reflector in the current interval. For Y.1731 probes, these are the actual data frames lost. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.12 | ColumnesaProbeHistoryR2PPkts | read-only | current | The total number of Received Packets in the current interval. In the case of Y.1731 probes, this reflects the number of DMRs (Delay Measurement Replies) receiv… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.13 | ColumnesaProbeHistoryR2PErredPkts | read-only | current | The total number of Received Packets in the current interval, which had errors such as length of received packet is less than the protocol header length, packe… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.14 | ColumnesaProbeHistoryR2PSyncErrs | read-only | current | The number of (time) Synchronization Errors from reflector to probe in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.15 | ColumnesaProbeHistoryR2PLostPkts | read-only | current | The number of Lost Pkts from reflector to probe in the current interval. For Y.1731 probes, these are the actual data frames lost. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.16 | ColumnesaProbeHistoryLostPkts | read-only | current | The total number of Lost Packets in the current interval. Packets which are not received from the reflector end beyond the configured timeout value are termed … |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.17 | ColumnesaProbeHistorySeqGaps | read-only | current | The total number of sequence gaps across all packets received in the current interval. If (Received Seq Number) is greater than or equal to (Last Received Seq … |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.18 | ColumnesaProbeHistoryOutOfSeqErrs | read-only | current | The total number of out of sequence errors across all packets received in the current interval. If (Received Seq Number) is less than or equal to (Last Receive… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.19 | ColumnesaProbeHistoryMinRoundTripDelay | read-only | current | The minimum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.20 | ColumnesaProbeHistoryMaxRoundTripDelay | read-only | current | The maximum round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.21 | ColumnesaProbeHistoryAvgRoundTripDelay | read-only | current | The average round-trip delay(in microseconds) across all packets received in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.22 | ColumnesaProbeHistorySumRoundTripDelay | read-only | current | The total sum of round trip delay(in microseconds) in the current interval. The reflector's processing time is excluded from the value. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.23 | ColumnesaProbeHistorySumOfSqRoundTripDelay | read-only | current | The sum of square of round trip delays in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.24 | ColumnesaProbeHistoryMinOnewayP2RDelay | read-only | current | The minimum one-way source to destination delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.25 | ColumnesaProbeHistoryMaxOnewayP2RDelay | read-only | current | The maximum one-way source to destination delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.26 | ColumnesaProbeHistoryAvgOnewayP2RDelay | read-only | current | The average one-way source to destination delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.27 | ColumnesaProbeHistorySumOnewayP2RDelay | read-only | current | The total sum of one-way delay from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.28 | ColumnesaProbeHistorySumOfSqOnewayP2RDelay | read-only | current | The sum of square of one-way delay from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.29 | ColumnesaProbeHistoryMinOnewayR2PDelay | read-only | current | The minimum one-way destination to source delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.30 | ColumnesaProbeHistoryMaxOnewayR2PDelay | read-only | current | The maximum one-way destination to source delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.31 | ColumnesaProbeHistoryAvgOnewayR2PDelay | read-only | current | The average one-way destination to source delay(in microseconds) across all packets received in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.32 | ColumnesaProbeHistorySumOnewayR2PDelay | read-only | current | The total sum of one-way delay from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.33 | ColumnesaProbeHistorySumOfSqOnewayR2PDelay | read-only | current | The sum of square of one-way delay from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.34 | ColumnesaProbeHistoryMinPosP2RJitter | read-only | current | The minimum positive one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.35 | ColumnesaProbeHistoryMaxPosP2RJitter | read-only | current | The maximum positive one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.36 | ColumnesaProbeHistoryNumPosP2RJitter | read-only | current | The total number of positive one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.37 | ColumnesaProbeHistorySumPosP2RJitter | read-only | current | The total sum of positive one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.38 | ColumnesaProbeHistorySumOfSqPosP2RJitter | read-only | current | The sum of square of positive one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.39 | ColumnesaProbeHistoryMinNegP2RJitter | read-only | current | The minimum negative one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.40 | ColumnesaProbeHistoryMaxNegP2RJitter | read-only | current | The maximum negative one-way jitter from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.41 | ColumnesaProbeHistoryNumNegP2RJitter | read-only | current | The total number of negative one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.42 | ColumnesaProbeHistorySumNegP2RJitter | read-only | current | The total sum of negative one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.43 | ColumnesaProbeHistorySumOfSqNegP2RJitter | read-only | current | The sum of square of negative one-way jitters from source to destination in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.44 | ColumnesaProbeHistoryMinPosR2PJitter | read-only | current | The minimum positive one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.45 | ColumnesaProbeHistoryMaxPosR2PJitter | read-only | current | The maximum positive one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.46 | ColumnesaProbeHistoryNumPosR2PJitter | read-only | current | The total number of positive one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.47 | ColumnesaProbeHistorySumPosR2PJitter | read-only | current | The total sum of positive one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.48 | ColumnesaProbeHistorySumOfSqPosR2PJitter | read-only | current | The sum of square of positive one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.49 | ColumnesaProbeHistoryMinNegR2PJitter | read-only | current | The minimum negative one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.50 | ColumnesaProbeHistoryMaxNegR2PJitter | read-only | current | The maximum negative one-way jitter from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.51 | ColumnesaProbeHistoryNumNegR2PJitter | read-only | current | The total number of negative one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.52 | ColumnesaProbeHistorySumNegR2PJitter | read-only | current | The total sum of negative one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.53 | ColumnesaProbeHistorySumOfSqNegR2PJitter | read-only | current | The sum of square of negative one-way jitters from destination to source in the current interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.54 | ColumnesaProbeHistoryY1731P2RNegLossOccurrences | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from Source MEP (Probe) to Destination MEP (Reflect… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.55 | ColumnesaProbeHistoryY1731R2PNegLossOccurrences | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of occurences of negative frame loss from to Destination MEP (Reflector) to Source MEP (… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.56 | ColumnesaProbeHistoryY1731RxLmSamples | read-only | current | This attribute is only applicable to Y.1731 probes. This flag indicates that at least one loss measurement sample was received for this bin period (LMRs receiv… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.57 | ColumnesaProbeHistoryY1731RxDmSamples | read-only | current | This attribute is only applicable to Y.1731 probes. This flag indicates that at least one delay measurement sample was received for this bin period (DMRs recei… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.58 | ColumnesaProbeHistoryY1731P2RFrames | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Source MEP (Probe) that are transmitted towards the Destin… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.59 | ColumnesaProbeHistoryY1731R2PFrames | read-only | current | This attribute is only applicable to Y.1731 probes. This is the number of data frames counted by the Destination MEP (Reflector) that are transmitted towards t… |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.60 | ColumnesaProbeHistoryAvgAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute P2R Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.61 | ColumnesaProbeHistoryAvgAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the average absolute R2P Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.62 | ColumnesaProbeHistoryMinAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute P2R Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.63 | ColumnesaProbeHistoryMinAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the minimum absolute R2P Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.64 | ColumnesaProbeHistoryMaxAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute P2R Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.65 | ColumnesaProbeHistoryMaxAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the maximum absolute R2P Jitter value. . |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.66 | ColumnesaProbeHistoryNumAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute P2R Jitters. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.67 | ColumnesaProbeHistoryNumAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the number of absolute R2P Jitters. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.68 | ColumnesaProbeHistorySumAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute P2R Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.69 | ColumnesaProbeHistorySumAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of absolute R2P Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.70 | ColumnesaProbeHistorySumOfSqAbsP2RJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute P2R Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.8.1.71 | ColumnesaProbeHistorySumOfSqAbsR2PJitter | read-only | current | This attribute is only applicable to Layer 3 ICMP Timestamp and Layer 2 Y.1731 probes. This is the sum of squares of absolute R2P Jitter values. |
| 1.3.6.1.4.1.2544.1.12.8.1.9 | TableesaProbeDistStatsConfigTable | not-accessible | current | A list of entries that need to be configured in order to obtain statistical distribution of ESA Probe collected data. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1 | RowesaProbeDistStatsConfigEntry | not-accessible | current | A row in the esaProbeDistStatsConfigTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.1 | ColumnesaProbeDistStatsConfigIndex | read-only | current | A unique index for each row. Each row corresponds to each enumeration type specified in EsaProbeDistStatsType. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.2 | ColumnesaProbeDistStatsConfigType | read-only | current | Indicates whether the statistical distribution is for round-trip delay (rt-delay), one-way probe to reflector delay (oneway-p2rdelay), one-way reflector to pro… |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.3 | ColumnesaProbeDistStatsConfigMinVal | read-write | current | Minimum sample value in distribution. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.4 | ColumnesaProbeDistStatsConfigMaxVal | read-write | current | Maximum sample value in distribution. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.5 | ColumnesaProbeDistStatsConfigNumBins | read-write | current | Number of distribution bins. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.6 | ColumnesaProbeDistStatsConfigLowBoundOfBin1 | read-write | current | The lower bound of the 1st bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.7 | ColumnesaProbeDistStatsConfigLowBoundOfBin2 | read-write | current | The lower bound of the 2nd bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.8 | ColumnesaProbeDistStatsConfigLowBoundOfBin3 | read-write | current | The lower bound of the 3rd bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.9 | ColumnesaProbeDistStatsConfigLowBoundOfBin4 | read-write | current | The lower bound of the 4th bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.10 | ColumnesaProbeDistStatsConfigLowBoundOfBin5 | read-write | current | The lower bound of the 5th bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.11 | ColumnesaProbeDistStatsConfigLowBoundOfBin6 | read-write | current | The lower bound of the 6th bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.12 | ColumnesaProbeDistStatsConfigLowBoundOfBin7 | read-write | current | The lower bound of the 7th bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.13 | ColumnesaProbeDistStatsConfigLowBoundOfBin8 | read-write | current | The lower bound of the 8th bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.9.1.14 | ColumnesaProbeDistStatsConfigLowBoundOfBin9 | read-write | current | The lower bound of the 9th bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.10 | TableesaProbeDistStatsTable | not-accessible | current | A list of entries that provide statistical distribution of ESA Probe collected data. |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1 | RowesaProbeDistStatsEntry | not-accessible | current | A row in the esaProbeDistStatsTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1.1 | ColumnesaProbeDistStatsDestinationIndex | read-only | current | An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since … |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1.2 | ColumnesaProbeDistStatsCOSIndex | read-only | current | An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly speci… |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1.3 | ColumnesaProbeDistStatsAction | read-write | current | Allows the Manager to clear the bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1.4 | ColumnesaProbeDistStatsCOS | read-only | current | The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported. |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1.5 | ColumnesaProbeDistStatsNumBins | read-only | current | Number of bins over which the statistical data is distributed. |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1.6 | ColumnesaProbeDistStatsLTMin | read-only | current | Number of sample data points which are less than the minimum value specified. |
| 1.3.6.1.4.1.2544.1.12.8.1.10.1.7 | ColumnesaProbeDistStatsGTMax | read-only | current | Number of sample data points which are greater than the maximum value specified. |
| 1.3.6.1.4.1.2544.1.12.8.1.11 | TableesaProbeDistStatsBinTable | not-accessible | current | A list of entries that provide statistical distribution of ESA Probe collected data for specific BINs. |
| 1.3.6.1.4.1.2544.1.12.8.1.11.1 | RowesaProbeDistStatsBinEntry | not-accessible | current | A row in the esaProbeDistStatsBinTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.11.1.1 | ColumnesaProbeDistStatsBinIndex | read-only | current | An index for each row that uniquely provides statistical data for a range. |
| 1.3.6.1.4.1.2544.1.12.8.1.11.1.2 | ColumnesaProbeDistStatsBinLower | read-only | current | The lower limit of values collected in this bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.11.1.3 | ColumnesaProbeDistStatsBinUpper | read-only | current | The upper limit of values collected in this bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.11.1.4 | ColumnesaProbeDistStatsBinNumSamples | read-only | current | Number of sample data points which fall between the lower and upper limits. |
| 1.3.6.1.4.1.2544.1.12.8.1.12 | TableesaProbeDistHistoryTable | not-accessible | current | A list of entries that provide statistical distribution history of ESA Probe collected data. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1 | RowesaProbeDistHistoryEntry | not-accessible | current | A row in the esaProbeDistHistoryTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.1 | ColumnesaProbeDistHistoryDestinationIndex | read-only | current | An integer index value used to uniquely identify a destination (Reflector) Index, in a point-to-multi point SLA. For Release 4.1 GE206, this value is 1, since … |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.2 | ColumnesaProbeDistHistoryCOSIndex | read-only | current | An integer index value used to uniquely identify SLA for a specific Class of Service. For Release 4.1 GE206, this value is 1, since the COS is explicitly speci… |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.3 | ColumnesaProbeDistHistoryIndex | read-only | current | An arbitrary integer index value used to uniquely identify this ESA Probe Distribution History entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.4 | ColumnesaProbeDistHistoryTime | read-only | current | Indicates the time of history bin creation. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.5 | ColumnesaProbeDistHistoryAction | read-write | current | Allows the Manager to clear the bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.6 | ColumnesaProbeDistHistoryCOS | read-only | current | The Class of Service. For Release 4.1 GE206, this value is cos-not-applicable, since multi COS SLA is not supported. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.7 | ColumnesaProbeDistHistoryNumBins | read-only | current | Number of bins over which the statistical data is distributed. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.8 | ColumnesaProbeDistHistoryLTMin | read-only | current | Number of sample data points which are less than the minimum value specified. |
| 1.3.6.1.4.1.2544.1.12.8.1.12.1.9 | ColumnesaProbeDistHistoryGTMax | read-only | current | Number of sample data points which are greater than the maximum value specified. |
| 1.3.6.1.4.1.2544.1.12.8.1.13 | TableesaProbeDistHistoryBinTable | not-accessible | current | A list of entries that provide historical statistical distribution of ESA Probe collected data for specific BINs. |
| 1.3.6.1.4.1.2544.1.12.8.1.13.1 | RowesaProbeDistHistoryBinEntry | not-accessible | current | A row in the esaProbeDistHistoryBinTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.13.1.1 | ColumnesaProbeDistHistoryBinIndex | read-only | current | An index for each row that uniquely provides statistical data for a range. |
| 1.3.6.1.4.1.2544.1.12.8.1.13.1.2 | ColumnesaProbeDistHistoryBinLower | read-only | current | The lower limit of values collected in this bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.13.1.3 | ColumnesaProbeDistHistoryBinUpper | read-only | current | The upper limit of values collected in this bin. |
| 1.3.6.1.4.1.2544.1.12.8.1.13.1.4 | ColumnesaProbeDistHistoryBinNumSamples | read-only | current | Number of sample data points which fall between the lower and upper limits. |
| 1.3.6.1.4.1.2544.1.12.8.1.14 | TableesaProbeStatsThresholdTable | not-accessible | current | A table of entries that allow manageability of ESA Probe Thresholds. |
| 1.3.6.1.4.1.2544.1.12.8.1.14.1 | RowesaProbeStatsThresholdEntry | not-accessible | current | A conceptual row in the esaProbeStatsThresholdTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.14.1.1 | ColumnesaProbeStatsThresholdIndex | read-only | current | An index that uniquely identifies an entry in the esaProbeStatsThresholdTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.14.1.2 | ColumnesaProbeStatsThresholdVariable | read-only | current | The object identifier of the particular variable to be sampled. Objects of the esaProbeStatsTable table are monitored. Only variables that resolve to an ASN.1 … |
| 1.3.6.1.4.1.2544.1.12.8.1.14.1.3 | ColumnesaProbeStatsThresholdAbsValueLo | read-write | current | Lower 32 bits of the absolute value of the threshold. |
| 1.3.6.1.4.1.2544.1.12.8.1.14.1.4 | ColumnesaProbeStatsThresholdAbsValueHi | read-write | current | Higher 32 bits of the absolute value of the threshold. |
| 1.3.6.1.4.1.2544.1.12.8.1.14.1.5 | ColumnesaProbeStatsThresholdMonValue | read-only | current | Monitored value corresponding to esaProbeStatsThresholdVariable. |
| 1.3.6.1.4.1.2544.1.12.8.1.15 | TableesaProbeCOSConfigTable | not-accessible | current | A list of entries corresponding to ESA Probes COS Configuration Levels. |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1 | RowesaProbeCOSConfigEntry | not-accessible | current | A row in the esaProbeCOSConfigTable. Entries can be created in this table by management application action. |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.1 | ColumnesaProbeCOSConfigIndex | read-create | current | An integer index value used to uniquely identify SLA (Service Level Agreement) for a specific Class of Service. Index 1 is associated with cos-0, index 2 with … |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.2 | ColumnesaProbeCOSConfigType | read-create | current | This is the Class of Service Type for Y.1731/SLM-SLR Probes, associated with the row. |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.3 | ColumnesaProbeCOSConfigInterval | read-create | current | This is the Class of Service Y.1731/SLM-SLR packet interval type. |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.4 | ColumnesaProbeCOSConfigPktSize | read-create | current | This is the Class of Service Y.1731/SLM-SLR Packet Size. This object enables specification of the TLV size for Delay Measurement Measures(DMMs) as well as Synt… |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.5 | ColumnesaProbeCOSConfigStorageType | read-create | current | The type of storage configured for this entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.6 | ColumnesaProbeCOSConfigRowStatus | read-create | current | The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description … |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.7 | ColumnesaProbeCOSConfigslmInterval | read-create | current | This allows specification of the interval between subsequent SLM packets. |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.8 | ColumnesaProbeCOSConfigslmPktSize | read-create | current | This allows specification of the SLM Packet Size. |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.9 | ColumnesaProbeCOSConfigSoamPmExtAvailFlrThreshold | read-write | current | Frame loss ratio threshold for Availability (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.10 | ColumnesaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus | read-write | current | This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is… |
| 1.3.6.1.4.1.2544.1.12.8.1.15.1.11 | ColumnesaProbeCOSConfigSoamPmExtConDeltaTsForAvail | read-write | current | This is the number of consecutive delta_ts used in the computation of availability/unavailability (n). |
| 1.3.6.1.4.1.2544.1.12.8.1.16 | TableesaProbeMultiDestinationTable | not-accessible | current | A list of entries corresponding to ESA Probes Multi Destinations. |
| 1.3.6.1.4.1.2544.1.12.8.1.16.1 | RowesaProbeMultiDestinationEntry | not-accessible | current | A row in the esaProbeMultiDestinationTable. Entries can be created in this table by management application action. Entries in this table represent destinations… |
| 1.3.6.1.4.1.2544.1.12.8.1.16.1.1 | ColumnesaProbeDestinationIndex | read-create | current | An integer index value used to uniquely identify a destination. |
| 1.3.6.1.4.1.2544.1.12.8.1.16.1.2 | ColumnesaProbeDestinationMepType | read-create | current | This attribute is applicable only for point-to-multipoint probes. This indicates if the destination MEP is specified using the MEP ID object esaProbeDestinatio… |
| 1.3.6.1.4.1.2544.1.12.8.1.16.1.3 | ColumnesaProbeDestinationMepMacAddr | read-create | current | This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. This MAC address will be the destination MAC address for f… |
| 1.3.6.1.4.1.2544.1.12.8.1.16.1.4 | ColumnesaProbeDestinationMepId | read-create | current | This attribute is applicable only for point-to-multipoint probes. It identifies the destination MEP. The MAC address of this RMEP ID from RMEP database will be… |
| 1.3.6.1.4.1.2544.1.12.8.1.16.1.5 | ColumnesaProbeDestinationStorageType | read-create | current | The type of storage configured for this entry. |
| 1.3.6.1.4.1.2544.1.12.8.1.16.1.6 | ColumnesaProbeDestinationRowStatus | read-create | current | The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description … |
| 1.3.6.1.4.1.2544.1.12.8.1.17 | TablebertControlTable | not-accessible | current | A list of entries for the control of BERT Streams. |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1 | RowbertControlEntry | not-accessible | current | A conceptual row in the bertControlTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1.1 | ColumnbertControlIndex | not-accessible | current | An arbitrary integer index value used to uniquely identify this BERT Control. |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1.2 | ColumnbertControlSourceEntity | read-write | current | Pointer to the entity on which the BERT will be started within a card. |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1.3 | ColumnbertControlTestMode | read-write | current | The mode of BERT to be performed. |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1.4 | ColumnbertControlDuration | read-write | current | This object enables specification of the time in seconds for BERT. BERT will be stopped after the specified time interval is exhausted. |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1.5 | ColumnbertControlStream | read-write | current | This object specifies which stream should be included in the BERT execution. Value of 0 indicates that no streams is selected by bertControlStream. Non 0 value… |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1.6 | ColumnbertControlAction | read-write | current | This object enables starting/stopping of traffic generation as well as resetting of monitored streams. This object may not be specified at configuration creati… |
| 1.3.6.1.4.1.2544.1.12.8.1.17.1.7 | ColumnbertControlTestStatus | read-only | current | This object reflects the current status of test set configuration entry. Upon creation, the status has a value of `initial'; the status changes to `in-progress… |
| 1.3.6.1.4.1.2544.1.12.8.1.18 | TablebertConfigStreamTable | not-accessible | current | A list of entries for the configuration of BERT Config Stream Specifications. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1 | RowbertConfigStreamEntry | not-accessible | current | A conceptual row in the bertConfigStreamTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.1 | ColumnbertConfigStreamIndex | not-accessible | current | An arbitrary integer index value used to uniquely identify this BERT configStream. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.2 | ColumnbertConfigStreamName | read-write | current | Symbolic Stream Name that can be associated with an BERT Config stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.3 | ColumnbertConfigStreamTxPattern | read-write | current | Allows specification of the Tx pattern of this BERT Config stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.4 | ColumnbertConfigStreamErrInjectEnabled | read-write | current | This object allows specification of whether Bit Error be injected. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.5 | ColumnbertConfigStreamErrInjectRate | read-write | current | Bit Error Rate, applicable when Error Injection is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.6 | ColumnbertConfigStreamErrInjectRateMultiplier | read-write | current | BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.7 | ColumnbertConfigStreamUserPatternLength | read-write | current | User defined testing pattern length. |
| 1.3.6.1.4.1.2544.1.12.8.1.18.1.8 | ColumnbertConfigStreamUserPattern | read-write | current | User defined testing pattern in a HEX format display string, applicable when test pattern is user defined. |
| 1.3.6.1.4.1.2544.1.12.8.1.19 | TablebertTestStreamTable | not-accessible | current | A list of entries containing results of a previous test. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1 | RowbertTestStreamEntry | not-accessible | current | A conceptual row in the bertTestStreamTable. Entries in this table show results of the current BERT. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.1 | ColumnbertTestStreamIndex | not-accessible | current | An integer index value corresponding to the stream index for which the BERT was initiated. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.2 | ColumnbertTestStreamName | read-write | current | Symbolic Stream Name that can be associated with an BERT stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.3 | ColumnbertTestStreamTxPattern | read-only | current | Allows specification of the Tx pattern of this BERT Test stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.4 | ColumnbertTestStreamErrInjectEnabled | read-only | current | This object allows specification of whether Bit Error be injected. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.5 | ColumnbertTestStreamErrInjectRate | read-only | current | Bit Error Rate, applicable when Error Injection is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.6 | ColumnbertTestStreamErrInjectRateMultiplier | read-only | current | BER value with 0.1 Step, in this release is fixed 10, only applicable when Error Injection is enabled. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.7 | ColumnbertTestStreamUserPatternLength | read-only | current | User defined testing pattern length. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.8 | ColumnbertTestStreamUserPattern | read-only | current | User defined testing pattern in a HEX format display string, applicable when test pattern is user defined. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.9 | ColumnbertTestStreamMonStartTime | read-only | current | The start time of the BERT for this stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.10 | ColumnbertTestStreamMonEndTime | read-only | current | The end time of the BERT for this stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.11 | ColumnbertTestStreamMonElapsedTime | read-only | current | The elapsed time of BERT for this stream in seconds. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.12 | ColumnbertTestStreamMonSyncState | read-only | current | The Sync State of the BERT. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.13 | ColumnbertTestStreamMonRxPattern | read-only | current | Allows specification of the Rx pattern of this BERT Test stream. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.14 | ColumnbertTestStreamMonSyncCounts | read-only | current | Allows specification of the Sync counts from test start. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.15 | ColumnbertTestStreamMonRxBitErrsSinceStart | read-only | current | Allows specification of the Received Errors since test start. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.16 | ColumnbertTestStreamMonRxBitsSinceStart | read-only | current | Allows specification of the Received Bits since test start. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.17 | ColumnbertTestStreamMonRxESsSinceStart | read-only | current | Allows specification of the Error seconds since test start. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.18 | ColumnbertTestStreamMonRxErrRateSinceStart | read-only | current | Allows specification of the Received BER Unit since test start. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.19 | ColumnbertTestStreamMonRxErrRateMultiplierSinceStart | read-only | current | Allows specification of the Received BER value with 0.1 Step since test start. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.20 | ColumnbertTestStreamMonRxBitErrsSinceLastSync | read-only | current | Allows specification of the Received Errors since last sync. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.21 | ColumnbertTestStreamMonRxBitsSinceLastSync | read-only | current | Allows specification of the Received Bits since last sync. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.22 | ColumnbertTestStreamMonRxESsSinceLastSync | read-only | current | Allows specification of the Received Error seconds since last sync. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.23 | ColumnbertTestStreamMonRxErrRateSinceLastSync | read-only | current | Allows specification of the Received BER Unit since last sync. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.24 | ColumnbertTestStreamMonRxErrRateMultiplierSinceLastSync | read-only | current | Allows specification of the Received BER value with 0.1 Step since last sync. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.25 | ColumnbertTestStreamConfigChangedFlag | read-only | current | This object provides information on whether the associated bertConfigStream is changed. |
| 1.3.6.1.4.1.2544.1.12.8.1.19.1.26 | ColumnbertTestStreamMonOOSSsSinceStart | read-only | current | This object means the Out of Sync Seconds since start. |
| 1.3.6.1.4.1.2544.1.12.8.1.20 | Tablef3EsaProbeCOSConfigSoamPmExtTable | not-accessible | current | A list of entries corresponding to ESA Probe Cos Configurations MEF 35. |
| 1.3.6.1.4.1.2544.1.12.8.1.20.1 | Rowf3EsaProbeCOSConfigSoamPmExtEntry | not-accessible | current | A row in the esaProbeCOSConfigTable MEF 35. Entries can be created in this table by management application action. |
| 1.3.6.1.4.1.2544.1.12.8.1.20.1.1 | Columnf3EsaProbeCOSConfigSoamPmExtAvailFlrThreshold | read-write | current | Frame loss ratio threshold for Availability (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.20.1.2 | Columnf3EsaProbeCOSConfigSoamPmExtFlrDeltaTNumLmPdus | read-write | current | This is the number of loss measurement PDUs. delta_t is this attribute multiplied by the loss measurement message period. For example, if SLM message period is… |
| 1.3.6.1.4.1.2544.1.12.8.1.20.1.3 | Columnf3EsaProbeCOSConfigSoamPmExtConDeltaTsForAvail | read-write | current | This is the number of consecutive delta_ts used in the computation of availability/unavailability (n). |
| 1.3.6.1.4.1.2544.1.12.8.1.21 | Tablef3EsaProbeStatsSoamPmExtTable | not-accessible | current | A collection of ESA Probe MEF 35 related statistics kept for a particular ESA Probe entity. These reflect the current data. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1 | Rowf3EsaProbeStatsSoamPmExtEntry | not-accessible | current | A conceptual row in the f3EsaProbeStatsSoamPmExtTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.1 | Columnf3EsaProbeStatsSoamPmExtMinP2RFlr | read-only | current | This is the minimum probe to reflector FLR (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.2 | Columnf3EsaProbeStatsSoamPmExtMaxP2RFlr | read-only | current | This is the maximum probe to reflector FLR (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.3 | Columnf3EsaProbeStatsSoamPmExtAvgP2RFlr | read-only | current | This is the average probe to reflector FLR (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.4 | Columnf3EsaProbeStatsSoamPmExtMinR2PFlr | read-only | current | This is the minimum reflector to probe FLR (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.5 | Columnf3EsaProbeStatsSoamPmExtMaxR2PFlr | read-only | current | This is the maximum reflector to probe FLR (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.6 | Columnf3EsaProbeStatsSoamPmExtAvgR2PFlr | read-only | current | This is the average reflector to probe FLR (m%). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.7 | Columnf3EsaProbeStatsSoamPmExtP2rSeverelyErroredDeltaTs | read-only | current | This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.8 | Columnf3EsaProbeStatsSoamPmExtR2PSeverelyErroredDeltaTs | read-only | current | This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.9 | Columnf3EsaProbeStatsSoamPmExtP2rAvailableTime | read-only | current | This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_… |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.10 | Columnf3EsaProbeStatsSoamPmExtR2PAvailableTime | read-only | current | This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_… |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.11 | Columnf3EsaProbeStatsSoamPmExtP2rUnavailableTime | read-only | current | This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It … |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.12 | Columnf3EsaProbeStatsSoamPmExtR2PUnavailableTime | read-only | current | This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It … |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.13 | Columnf3EsaProbeStatsSoamPmExtMinAbsRTJitter | read-only | current | Minimum absolute round-trip (two-way) jitter in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.14 | Columnf3EsaProbeStatsSoamPmExtMaxAbsRTJitter | read-only | current | Maximum absolute round-trip (two-way) jitter in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.15 | Columnf3EsaProbeStatsSoamPmExtAvgAbsRTJitter | read-only | current | Average absolute round-trip (two-way) jitter in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.16 | Columnf3EsaProbeStatsSoamPmExtNumAbsRTJitter | read-only | current | Number of absolute round-trip (two-way) jitter samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.17 | Columnf3EsaProbeStatsSoamPmExtSumAbsRTJitter | read-only | current | Sum of absolute round-trip (two-way) jitter samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.18 | Columnf3EsaProbeStatsSoamPmExtSumOfSqAbsRTJitter | read-only | current | Sum of squares of absolute round-trip (two-way) jitter samples (microseconds^2). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.19 | Columnf3EsaProbeStatsSoamPmExtMaxP2RFDR | read-only | current | Maximum P2R (Forward) FDR in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.20 | Columnf3EsaProbeStatsSoamPmExtAvgP2RFDR | read-only | current | Average P2R (Forward) FDR in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.21 | Columnf3EsaProbeStatsSoamPmExtNumP2RFDR | read-only | current | Number of P2R (Forward) FDR samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.22 | Columnf3EsaProbeStatsSoamPmExtSumP2RFDR | read-only | current | Sum of P2R (Forward) FDR samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.23 | Columnf3EsaProbeStatsSoamPmExtSumOfSqP2RFDR | read-only | current | Sum of squares of P2R (Forward) FDR samples (microseconds^2). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.24 | Columnf3EsaProbeStatsSoamPmExtMaxR2PFDR | read-only | current | Maximum R2P (Backward) FDR in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.25 | Columnf3EsaProbeStatsSoamPmExtAvgR2PFDR | read-only | current | Average R2P (Backward) FDR in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.26 | Columnf3EsaProbeStatsSoamPmExtNumR2PFDR | read-only | current | Number of R2P (Backward) FDR samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.27 | Columnf3EsaProbeStatsSoamPmExtSumR2PFDR | read-only | current | Sum of R2P (Backward) FDR samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.28 | Columnf3EsaProbeStatsSoamPmExtSumOfSqR2PFDR | read-only | current | Sum of squares of R2P (Backward) FDR samples (microseconds^2). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.29 | Columnf3EsaProbeStatsSoamPmExtMaxRTFDR | read-only | current | Maximum round-trip (two-way) FDR in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.30 | Columnf3EsaProbeStatsSoamPmExtAvgRTFDR | read-only | current | Average round-trip (two-way) FDR in a measurement interval (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.31 | Columnf3EsaProbeStatsSoamPmExtNumRTFDR | read-only | current | Number of round-trip (two-way) FDR samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.32 | Columnf3EsaProbeStatsSoamPmExtSumRTFDR | read-only | current | Sum of round-trip (two-way) FDR samples (microseconds). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.33 | Columnf3EsaProbeStatsSoamPmExtSumOfSqRTFDR | read-only | current | Sum of squares of round-trip (two-way) FDR samples (microseconds^2). |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.34 | Columnf3EsaProbeStatsSoamPmExtP2rAvailableDeltaTs | read-only | current | Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.35 | Columnf3EsaProbeStatsSoamPmExtR2pAvailableDeltaTs | read-only | current | Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.36 | Columnf3EsaProbeStatsSoamPmExtP2rUnavailableDeltaTs | read-only | current | Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.37 | Columnf3EsaProbeStatsSoamPmExtR2pUnavailableDeltaTs | read-only | current | Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.21.1.38 | Columnf3EsaProbeStatsSoamPmExtElapsedTime | read-only | current | The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or ba… |
| 1.3.6.1.4.1.2544.1.12.8.1.22 | Tablef3EsaProbeHistorySoamPmExtTable | not-accessible | current | A collection of ESA Probe MEF 35 related history kept for a particular ESA Probe entity. These reflect the history data. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1 | Rowf3EsaProbeHistorySoamPmExtEntry | not-accessible | current | A conceptual row in the f3EsaProbeHistorySoamPmExtTable. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.1 | Columnf3EsaProbeHistorySoamPmExtMinP2RFlr | read-only | current | This is the minimum probe to reflector FLR. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.2 | Columnf3EsaProbeHistorySoamPmExtMaxP2RFlr | read-only | current | This is the maximum probe to reflector FLR. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.3 | Columnf3EsaProbeHistorySoamPmExtAvgP2RFlr | read-only | current | This is the average probe to reflector FLR. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.4 | Columnf3EsaProbeHistorySoamPmExtMinR2PFlr | read-only | current | This is the minimum reflector to probe FLR. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.5 | Columnf3EsaProbeHistorySoamPmExtMaxR2PFlr | read-only | current | This is the maximum reflector to probe FLR. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.6 | Columnf3EsaProbeHistorySoamPmExtAvgR2PFlr | read-only | current | This is the average reflector to probe FLR. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.7 | Columnf3EsaProbeHistorySoamPmExtP2rSeverelyErroredDeltaTs | read-only | current | This is the number of delta_ts in which the FLR is greater than availability threshold in the probe to reflector direction. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.8 | Columnf3EsaProbeHistorySoamPmExtR2PSeverelyErroredDeltaTs | read-only | current | This is the number of delta_ts in which the FLR is greater than availability threshold in the reflector to probe direction. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.9 | Columnf3EsaProbeHistorySoamPmExtP2rAvailableTime | read-only | current | This is the probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_… |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.10 | Columnf3EsaProbeHistorySoamPmExtR2PAvailableTime | read-only | current | This is the reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_… |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.11 | Columnf3EsaProbeHistorySoamPmExtP2rUnavailableTime | read-only | current | This is the probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It … |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.12 | Columnf3EsaProbeHistorySoamPmExtR2PUnavailableTime | read-only | current | This is the reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. It … |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.13 | Columnf3EsaProbeHistorySoamPmExtMinAbsRTJitter | read-only | current | Minimum absolute round-trip (two-way) jitter in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.14 | Columnf3EsaProbeHistorySoamPmExtMaxAbsRTJitter | read-only | current | Maximum absolute round-trip (two-way) jitter in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.15 | Columnf3EsaProbeHistorySoamPmExtAvgAbsRTJitter | read-only | current | Average absolute round-trip (two-way) jitter in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.16 | Columnf3EsaProbeHistorySoamPmExtNumAbsRTJitter | read-only | current | Number of absolute round-trip (two-way) jitter samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.17 | Columnf3EsaProbeHistorySoamPmExtSumAbsRTJitter | read-only | current | Sum of absolute round-trip (two-way) jitter samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.18 | Columnf3EsaProbeHistorySoamPmExtSumOfSqAbsRTJitter | read-only | current | Sum of squares of absolute round-trip (two-way) jitter samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.19 | Columnf3EsaProbeHistorySoamPmExtMaxP2RFDR | read-only | current | Maximum P2R (Forward) FDR in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.20 | Columnf3EsaProbeHistorySoamPmExtAvgP2RFDR | read-only | current | Average P2R (Forward) FDR in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.21 | Columnf3EsaProbeHistorySoamPmExtNumP2RFDR | read-only | current | Number of P2R (Forward) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.22 | Columnf3EsaProbeHistorySoamPmExtSumP2RFDR | read-only | current | Sum of P2R (Forward) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.23 | Columnf3EsaProbeHistorySoamPmExtSumOfSqP2RFDR | read-only | current | Sum of squares of P2R (Forward) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.24 | Columnf3EsaProbeHistorySoamPmExtMaxR2PFDR | read-only | current | Maximum R2P (Backward) FDR in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.25 | Columnf3EsaProbeHistorySoamPmExtAvgR2PFDR | read-only | current | Average R2P (Backward) FDR in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.26 | Columnf3EsaProbeHistorySoamPmExtNumR2PFDR | read-only | current | Number of R2P (Backward) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.27 | Columnf3EsaProbeHistorySoamPmExtSumR2PFDR | read-only | current | Sum of R2P (Backward) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.28 | Columnf3EsaProbeHistorySoamPmExtSumOfSqR2PFDR | read-only | current | Sum of squares of R2P (Backward) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.29 | Columnf3EsaProbeHistorySoamPmExtMaxRTFDR | read-only | current | Maximum round-trip (two-way) FDR in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.30 | Columnf3EsaProbeHistorySoamPmExtAvgRTFDR | read-only | current | Average round-trip (two-way) FDR in a measurement interval. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.31 | Columnf3EsaProbeHistorySoamPmExtNumRTFDR | read-only | current | Number of round-trip (two-way) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.32 | Columnf3EsaProbeHistorySoamPmExtSumRTFDR | read-only | current | Sum of round-trip (two-way) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.33 | Columnf3EsaProbeHistorySoamPmExtSumOfSqRTFDR | read-only | current | Sum of squares of round-trip (two-way) FDR samples. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.34 | Columnf3EsaProbeHistorySoamPmExtP2rAvailableDeltaTs | read-only | current | Probe to reflector available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.35 | Columnf3EsaProbeHistorySoamPmExtR2pAvailableDeltaTs | read-only | current | Reflector to probe available delta_ts which begins to increment when FLR is less than or equal to availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.36 | Columnf3EsaProbeHistorySoamPmExtP2rUnavailableDeltaTs | read-only | current | Probe to reflector unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.37 | Columnf3EsaProbeHistorySoamPmExtR2pUnavailableDeltaTs | read-only | current | Reflector to probe unavailable delta_ts which begins to increment when FLR is greater than availability threshold for 'n' consecutive delta_ts. |
| 1.3.6.1.4.1.2544.1.12.8.1.22.1.38 | Columnf3EsaProbeHistorySoamPmExtElapsedTime | read-only | current | The elapsed time (monotonic time) for the interval which could be less or more than measurement interval based on which the Time of Day was moved forward or ba… |
| 1.3.6.1.4.1.2544.1.12.8.2 | NodecmServAssuranceNotifications | |||
| 1.3.6.1.4.1.2544.1.12.8.2.1 | NotificationcmOperateLoopbackTrap | current | This is the Operate Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objec… | |
| 1.3.6.1.4.1.2544.1.12.8.2.2 | NotificationcmReleaseLoopbackTrap | current | This is the Release Loopback Notification sent by the agent. The actual attribute value is sent by the agent in the form of a varbind list, as additional objec… | |
| 1.3.6.1.4.1.2544.1.12.8.2.3 | NotificationesaProbeThresholdCrossingAlert | current | This trap is sent each time a threshold on a PM condition on ESA Probe is crossed. | |
| 1.3.6.1.4.1.2544.1.12.8.3 | NodecmServAssuranceConformance | |||
| 1.3.6.1.4.1.2544.1.12.8.3.1 | NodecmServAssuranceCompliances | |||
| 1.3.6.1.4.1.2544.1.12.8.3.1.1 | CompliancecmServAssuranceCompliance | current | Describes the requirements for conformance to the CM ServAssurance group. | |
| 1.3.6.1.4.1.2544.1.12.8.3.2 | NodecmServAssuranceGroups | |||
| 1.3.6.1.4.1.2544.1.12.8.3.2.1 | GroupcmServAssuranceObjectGroup | deprecated | ***************** THIS OBJECT GROUP IS NOW DEPRECATED *************** A collection of objects used to manage the CM ServAssurance group. | |
| 1.3.6.1.4.1.2544.1.12.8.3.2.2 | GroupcmServAssuranceNotifGroup | deprecated | ***************** THIS OBJECT GROUP IS NOW DEPRECATED ****************** A collection of notifications used in the CM ServAssurance group. | |
| 1.3.6.1.4.1.2544.1.12.8.3.2.3 | GroupcmEcpaGroup | current | A collection of objects used to manage the CM ServAssurance ECPA functionality. | |
| 1.3.6.1.4.1.2544.1.12.8.3.2.4 | GroupcmEsaGroup | current | A collection of objects used to manage the CM ServAssurance ESA functionality. | |
| 1.3.6.1.4.1.2544.1.12.8.3.2.5 | GroupcmServAssuranceGenNotifGroup | current | A collection of notifications used in the generic CM ServAssurance functionality. | |
| 1.3.6.1.4.1.2544.1.12.8.3.2.6 | GroupcmServAssuranceEsaNotifGroup | current | A collection of notifications used in the CM ServAssurance ESA functionality. | |
| 1.3.6.1.4.1.2544.1.12.8.3.2.7 | GroupcmBertGroup | current | A collection of objects used to manage the CM ServAssurance BERT functionality. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BertControlAction | INTEGER { not-applicable(0), start(1), stop(2) } | current | BER Test Control Action. |
| BerTestMode | INTEGER { not-applicable(0), generator(1), monitor(2), singleend(3) } | current | BER Test Control Test Mode. |
| BerTestStatus | INTEGER { not-applicable(0), running (1), not-running (2) } | current | BER Test Status. |
| BertPattern | INTEGER { not-applicable(0), all-0(1), all-1(2), alt-1100(3), bit-1in8(4), bit-3in24(5), bit-2exp20-qrss(6), bit-2exp11-prbs(7), bit-2exp15-prbs(8), bit-2exp23-prbs(9), userdefined(10) } | current | BERT Tx Pattern. |
| BertSyncState | INTEGER { not-applicable(0), sync(1), outofsync(2) } | current | BERT Sync State. |
| BertUserPatternLength | INTEGER { not-applicable(0), length-1byte(1), length-2byte(2), length-3byte(3), length-4byte(4) } | current | BERT Error Rate. |
| EcpaControlAction | INTEGER { not-applicable(0), start(1), stop(2) } | current | ECPA Control Action. |
| EcpaPayloadType | INTEGER { fixed (1), random (2) } | current | ECPA Payload Type. |
| EcpaTestStatus | INTEGER { initial (1), in-progress (2), stopped (3), completed (4), aborted (5) } | current | ECPA Test Status. |
| EcpaTestType | INTEGER { duration(1), numframes(2), continuous(3) } | current | ECPA Control Test Type. |
| EsaAction | INTEGER { not-applicable(0), suspend(1), resume(2), addEsaProbe(3), removeEsaProbe(4) } | current | ESA Scheduled Group/Reflector Action. |
| EsaProbeDirection | INTEGER { up(1), down(2) } | current | ESA Probe Direction. |
| EsaProbeDistStatsType | INTEGER { roundtrip-delay(1), oneway-p2r-delay(2), oneway-r2p-delay(3), oneway-p2r-jitter(4), oneway-r2p-jitter(5), oneway-p2r-absjitter(6), oneway-r2p-absjitter(7), roundtrip-absjitter(8), oneway-p2r-fdr(9), oneway-r2p-fdr(10), roundtrip-fdr(11) } | current | Indicates the ESA Probe Statistics Distribution Type. |
| EsaProbeHistoryIntervalType | INTEGER { interval-1min(1), interval-5min(2), interval-10min(3), interval-15min(4), interval-60min(5) } | current | ESA Probe Y1731 History Interval Types. |
| EsaProbePktIntervalType | INTEGER { not-applicable(0), interval-10ms(1), interval-100ms(2), interval-1sec(3), interval-10sec(4), interval-1min(5) } | current | Interval Type used for LMM and DMM messages. |
| EsaProbePmIntervalType | INTEGER { current(1), rollover(2) } | current | ESA Probe PM Interval Types. |
| EsaProbeProtocol | INTEGER { icmpEcho(1), udpEcho(2), icmpTimestamp(3), y1731(4), y1731-slm-slr(5), y1731-slm-dmm(6) } | current | ESA Probe Protocol Types. |
| EsaProbeSLAMonitorType | INTEGER { not-applicable(0), point-to-point(1), point-to-multipoint(2) } | current | ESA Probe SLA Monitor Type. |
| EsaReflectorDirection | INTEGER { up(1), down(2) } | current | ESA Reflector Direction. |